[Connexion Wifi] Installation Wifi (en cours)

Questions et astuces concernant l'installation et la configuration d'archlinux
Avatar de l’utilisateur
benjarobin
Maître du Kyudo
Messages : 17187
Inscription : sam. 30 mai 2009, 15:48
Localisation : Lyon

Re: [Connexion Wifi] Installation Wifi (en cours)

Message par benjarobin »

Supprime aussi : /etc/systemd/system/multi-user.target.wants/wpa_supplicant@IF0.service
banditblue a écrit : jeu. 09 avr. 2020, 17:00j'ai effacé les services que tu m'a demandé de supprimé uniquement
J'aime bien quand tu ne réponds presque jamais à mes questions... Tu as encore répondu à coté.
Zsh | KDE | PC fixe : core i7, carte nvidia
Titre d'un sujet : [Thème] Sujet (état) / Règles du forum
Avatar de l’utilisateur
banditblue
Elfe
Messages : 591
Inscription : dim. 10 janv. 2010, 10:19

Re: [Connexion Wifi] Installation Wifi (en cours)

Message par banditblue »

J'aime bien quand tu ne réponds presque jamais à mes questions... Tu as encore répondu à coté.
désolé, mais voila jusqu'a present j'ai réussi a faire pas mal de chose sous linux, avec l'aide de la communauté..
le gros soucis, c'est que quand je ne comprend pas le fonctionnement, je but dessus et je n'avance plus
La connaîssance n'a pas de limite.
Mais sa valeur, est d'autant plus grande, une fois partagé


Pc fixe --- MSI MPG Z490 Gaming Edge WiFi, I9-9900Kf, RTX3070Ti, 64Go DDR4, SSD 1Tera nvme gen4 Samsung 980 pro, SSD 1Tera WD Blacksn850X,3HDD 5Tera
Eeepc Asus 1015pem --- Intel Atom N550 Dual-core 1.5Ghz / DD 1Tera 7200rpm / Ram 2Go

Screenshot + Les Conky ===> http://forums.archlinux.fr/post85405.html#p85405
Avatar de l’utilisateur
banditblue
Elfe
Messages : 591
Inscription : dim. 10 janv. 2010, 10:19

Re: [Connexion Wifi] Installation Wifi (en cours)

Message par banditblue »

Je ne sais si j'ai bon jusque la...le soucis c'est quand j'essaye d'activer le wifi (wlp0s20f0u2), celui si et toujours dormant

Image

on vois bien les opération que je fait en ligne de commande dans mon terminal
je les affiche ici au cas ou on ne vois pas bien sur l'image

Code : Tout sélectionner

[moi@ArchLinuxI7 ~]$ ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
3: enp0s31f6: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000
    link/ether 4c:cc:6a:00:41:9b brd ff:ff:ff:ff:ff:ff
4: wlp0s20f0u2: <NO-CARRIER,BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2312 qdisc mq state DORMANT mode DORMANT group default qlen 1000
    link/ether 5e:55:68:df:17:df brd ff:ff:ff:ff:ff:ff permaddr 04:d4:c4:5d:ff:8c
[moi@ArchLinuxI7 ~]$ ip link set enp0s31f6 down
RTNETLINK answers: Operation not permitted
[moi@ArchLinuxI7 ~]$ ip link set wlp0s20f0u2 up
RTNETLINK answers: Operation not permitted
[moi@ArchLinuxI7 ~]$ su
Mot de passe : 
[root@ArchLinuxI7 moi]# ip link set wlp0s20f0u2 up
[root@ArchLinuxI7 moi]# ip link set enp0s31f6 down
[root@ArchLinuxI7 moi]# ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
3: enp0s31f6: <BROADCAST,MULTICAST> mtu 1500 qdisc fq_codel state DOWN mode DEFAULT group default qlen 1000
    link/ether 4c:cc:6a:00:41:9b brd ff:ff:ff:ff:ff:ff
4: wlp0s20f0u2: <NO-CARRIER,BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2312 qdisc mq state DORMANT mode DORMANT group default qlen 1000
    link/ether 5e:55:68:df:17:df brd ff:ff:ff:ff:ff:ff permaddr 04:d4:c4:5d:ff:8c
[root@ArchLinuxI7 moi]# ip link set enp0s31f6 up
[root@ArchLinuxI7 moi]# 
j'ai aussi tenté de configurer ma connection dans network manager comme on peu le voir
La connaîssance n'a pas de limite.
Mais sa valeur, est d'autant plus grande, une fois partagé


Pc fixe --- MSI MPG Z490 Gaming Edge WiFi, I9-9900Kf, RTX3070Ti, 64Go DDR4, SSD 1Tera nvme gen4 Samsung 980 pro, SSD 1Tera WD Blacksn850X,3HDD 5Tera
Eeepc Asus 1015pem --- Intel Atom N550 Dual-core 1.5Ghz / DD 1Tera 7200rpm / Ram 2Go

Screenshot + Les Conky ===> http://forums.archlinux.fr/post85405.html#p85405
Avatar de l’utilisateur
benjarobin
Maître du Kyudo
Messages : 17187
Inscription : sam. 30 mai 2009, 15:48
Localisation : Lyon

Re: [Connexion Wifi] Installation Wifi (en cours)

Message par benjarobin »

Tu dois juste faire ceci :
- Supprimer les profiles nommés : eth0, enp0s31f6, et FREEBOX_2012
- Avoir un Wifi dont le SSID ne soit pas caché...
- Redémarrer
- Après un démarrage ne touche surtout pas à la ligne de commande, tout ce que tu pourrais faire et de rentrer en conflit avec ce que fait NetworkManager
- Clique sur ton réseau Wifi qui apparaît dans la liste de l'interface graphique et sélectionne le mot de passe quand on te le demande. C'est tout.
Pour cela il suffit de faire un clique gauche sur l’icône, puis de cliquer sur ton Wifi qui doit apparaître dans la liste

Note: Les informations que tu as saisis manuellement dans l'interface graphique ne sont pas du tout bonne.
Zsh | KDE | PC fixe : core i7, carte nvidia
Titre d'un sujet : [Thème] Sujet (état) / Règles du forum
Avatar de l’utilisateur
banditblue
Elfe
Messages : 591
Inscription : dim. 10 janv. 2010, 10:19

Re: [Connexion Wifi] Installation Wifi (en cours)

Message par banditblue »

pour le SSID non caché je t'avoue que j'ai testé toutes les solution sur ma freebox
en allant sur la page de configuration du wifi caché ou visible, j'ai essayé de connecté (Etat du service) puis en redémarrant la freebox, idem en déconnectant le bouton rien n'y fait
Image

idem en changeant les canaux
Image
La connaîssance n'a pas de limite.
Mais sa valeur, est d'autant plus grande, une fois partagé


Pc fixe --- MSI MPG Z490 Gaming Edge WiFi, I9-9900Kf, RTX3070Ti, 64Go DDR4, SSD 1Tera nvme gen4 Samsung 980 pro, SSD 1Tera WD Blacksn850X,3HDD 5Tera
Eeepc Asus 1015pem --- Intel Atom N550 Dual-core 1.5Ghz / DD 1Tera 7200rpm / Ram 2Go

Screenshot + Les Conky ===> http://forums.archlinux.fr/post85405.html#p85405
Avatar de l’utilisateur
benjarobin
Maître du Kyudo
Messages : 17187
Inscription : sam. 30 mai 2009, 15:48
Localisation : Lyon

Re: [Connexion Wifi] Installation Wifi (en cours)

Message par benjarobin »

Si tu avais répondu à mes questions, je pourrais peut être t'aider... (J'avais déjà posé cette question...) C'est quoi le modèle de la Freebox ?
Tu ne devrait pas utliser le canal 13 (Pour les tests essais déjà avec le canal 6), et encore moins utiliser une clé WEP (autant pas mettre de clé)...
Normalement la configuration du Wifi ne se fait plus via cette page Web ! Elle se fait depuis l'interface de la Freebox...
Est-ce que tu redémarres le bon boîtier ? Tu débranches quoi ? Photo de ton installation ?
Zsh | KDE | PC fixe : core i7, carte nvidia
Titre d'un sujet : [Thème] Sujet (état) / Règles du forum
Avatar de l’utilisateur
banditblue
Elfe
Messages : 591
Inscription : dim. 10 janv. 2010, 10:19

Re: [Connexion Wifi] Installation Wifi (en cours)

Message par banditblue »

benjarobin a écrit : ven. 10 avr. 2020, 14:11 Si tu avais répondu à mes questions, je pourrais peut être t'aider... (J'avais déjà posé cette question...) C'est quoi le modèle de la Freebox ?
Tu ne devrait pas utliser le canal 13 (Pour les tests essais déjà avec le canal 6), et encore moins utiliser une clé WEP (autant pas mettre de clé)...
Normalement la configuration du Wifi ne se fait plus via cette page Web ! Elle se fait depuis l'interface de la Freebox...
Est-ce que tu redémarres le bon boîtier ? Tu débranches quoi ? Photo de ton installation ?
je vais tenter de repondre

Code : Tout sélectionner

C'est quoi le modèle de la Freebox ?
c'est la Freebox Revolution

Code : Tout sélectionner

Tu ne devrait pas utliser le canal 13 (Pour les tests essais déjà avec le canal 6),
j'utilise le canal 11, c'est celui qui etait fonctionnel jusqu'a present

Code : Tout sélectionner

et encore moins utiliser une clé WEP
je vais tenter de passer en wpa (va falloir que je change tout mes peripherique pour qu'il soit tous fonctionnel en wifi)

Code : Tout sélectionner

Est-ce que tu redémarres le bon boîtier? Tu débranches quoi ? Photo de ton installation ?
oui, ne suis pas un débutant, je ne demarre pas le lecteur blu-ray on se comprend
je débranche la prise de la freebox sur le secteur
qu'est ce que tu entend par photo de mon installation ???
La connaîssance n'a pas de limite.
Mais sa valeur, est d'autant plus grande, une fois partagé


Pc fixe --- MSI MPG Z490 Gaming Edge WiFi, I9-9900Kf, RTX3070Ti, 64Go DDR4, SSD 1Tera nvme gen4 Samsung 980 pro, SSD 1Tera WD Blacksn850X,3HDD 5Tera
Eeepc Asus 1015pem --- Intel Atom N550 Dual-core 1.5Ghz / DD 1Tera 7200rpm / Ram 2Go

Screenshot + Les Conky ===> http://forums.archlinux.fr/post85405.html#p85405
Avatar de l’utilisateur
benjarobin
Maître du Kyudo
Messages : 17187
Inscription : sam. 30 mai 2009, 15:48
Localisation : Lyon

Re: [Connexion Wifi] Installation Wifi (en cours)

Message par benjarobin »

La Freebox révolution ne se configure pas depuis la page Web que tu as donné... Je sais j'ai la même Freebox !
Va sur http://mafreebox.freebox.fr/

Vraiment, cacher le SSID cela ne sert à rien, mais être en WEP c'est une aberration. Mais peut être que la configuration du Wifi n'est pas en WEP, car il n'y a aucune synchronisation entre les informations de la page de Free et la configuration interne de la Freebox.
Au passage c'est une aberration d'avoir gardé cette page, il devrait la supprimer... Je crois que les paramètres sont uniquement appliqué si tu fait un hard reset de la Box (la débrancher ne suffit pas !)
Zsh | KDE | PC fixe : core i7, carte nvidia
Titre d'un sujet : [Thème] Sujet (état) / Règles du forum
Avatar de l’utilisateur
banditblue
Elfe
Messages : 591
Inscription : dim. 10 janv. 2010, 10:19

Re: [Connexion Wifi] Installation Wifi (en cours)

Message par banditblue »

Image
La connaîssance n'a pas de limite.
Mais sa valeur, est d'autant plus grande, une fois partagé


Pc fixe --- MSI MPG Z490 Gaming Edge WiFi, I9-9900Kf, RTX3070Ti, 64Go DDR4, SSD 1Tera nvme gen4 Samsung 980 pro, SSD 1Tera WD Blacksn850X,3HDD 5Tera
Eeepc Asus 1015pem --- Intel Atom N550 Dual-core 1.5Ghz / DD 1Tera 7200rpm / Ram 2Go

Screenshot + Les Conky ===> http://forums.archlinux.fr/post85405.html#p85405
Avatar de l’utilisateur
benjarobin
Maître du Kyudo
Messages : 17187
Inscription : sam. 30 mai 2009, 15:48
Localisation : Lyon

Re: [Connexion Wifi] Installation Wifi (en cours)

Message par benjarobin »

En terme de sécurité tu dois sélectionner WPA2-PSK/AES
Zsh | KDE | PC fixe : core i7, carte nvidia
Titre d'un sujet : [Thème] Sujet (état) / Règles du forum
Avatar de l’utilisateur
banditblue
Elfe
Messages : 591
Inscription : dim. 10 janv. 2010, 10:19

Re: [Connexion Wifi] Installation Wifi (en cours)

Message par banditblue »

oui je l'ai fait juste apres avoir posté la photo
pour preserver ma connection wifi
La connaîssance n'a pas de limite.
Mais sa valeur, est d'autant plus grande, une fois partagé


Pc fixe --- MSI MPG Z490 Gaming Edge WiFi, I9-9900Kf, RTX3070Ti, 64Go DDR4, SSD 1Tera nvme gen4 Samsung 980 pro, SSD 1Tera WD Blacksn850X,3HDD 5Tera
Eeepc Asus 1015pem --- Intel Atom N550 Dual-core 1.5Ghz / DD 1Tera 7200rpm / Ram 2Go

Screenshot + Les Conky ===> http://forums.archlinux.fr/post85405.html#p85405
Avatar de l’utilisateur
benjarobin
Maître du Kyudo
Messages : 17187
Inscription : sam. 30 mai 2009, 15:48
Localisation : Lyon

Re: [Connexion Wifi] Installation Wifi (en cours)

Message par benjarobin »

Dans tous les cas, tu dois reconfigurer tout le monde pour utiliser ce niveau de sécurité. La question ne se pose même pas. Ton Wifi est sinon totalement ouvert. et je te conseil au passage de changer la clé car tout le monde doit l'avoir maintenant... Et pour que ce soit même plus simple, je te conseil même de changer le SSID du Wifi, cela évitera de devoir supprimer manuellement la configuration dans chaque appareil.

Au pire ainsi tu pourras plus facilement revenir en arrière. Donc change tout, niveau de sécurité, clé et SSID

Et donc est-ce que maintenant tu vois le réseau Wifi ?
Zsh | KDE | PC fixe : core i7, carte nvidia
Titre d'un sujet : [Thème] Sujet (état) / Règles du forum
Avatar de l’utilisateur
banditblue
Elfe
Messages : 591
Inscription : dim. 10 janv. 2010, 10:19

Re: [Connexion Wifi] Installation Wifi (en cours)

Message par banditblue »

non mon réseau n'est pas visible il ne trouve rien

Code : Tout sélectionner

[BSS 30:93:bc:12:af:b0(on wlp0s20f0u2)
	TSF: 1477026651 usec (0d, 00:24:37)
	freq: 2462
	beacon interval: 100 TUs
	capability: ESS Privacy ShortSlotTime (0x0411)
	signal: -85.00 dBm
	last seen: 0 ms ago
	Information elements from Probe Response frame:
	SSID: Livebox-AFB0
	Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0 
	DS Parameter set: channel 11
	Country: FR	Environment: Indoor/Outdoor
		Channels [1 - 13] @ 20 dBm
	ERP: Barker_Preamble_Mode
	Extended supported rates: 6.0 9.0 12.0 48.0 
	RSN:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: PSK
		 * Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
	BSS Load:
		 * station count: 1
		 * channel utilisation: 17/255
		 * available admission capacity: 0 [*32us]
	HT capabilities:
		Capabilities: 0x9ac
			HT20
			SM Power Save disabled
			RX HT20 SGI
			TX STBC
			RX STBC 1-stream
			Max AMSDU length: 7935 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 8 usec (0x06)
		HT RX MCS rate indexes supported: 0-15
		HT TX MCS rate indexes are undefined
	HT operation:
		 * primary channel: 11
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 1
		 * HT protection: no
		 * non-GF present: 1
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	Overlapping BSS scan params:
		 * passive dwell: 20 TUs
		 * active dwell: 10 TUs
		 * channel width trigger scan interval: 300 s
		 * scan passive total per channel: 200 TUs
		 * scan active total per channel: 20 TUs
		 * BSS width channel transition delay factor: 5
		 * OBSS Scan Activity Threshold: 0.25 %
	Extended capabilities:
		 * HT Information Exchange Supported
		 * Extended Channel Switching
		 * BSS Transition
		 * Operating Mode Notification
	WPS:	 * Version: 1.0
		 * Wi-Fi Protected Setup State: 2 (Configured)
		 * Response Type: 3 (AP)
		 * UUID: 33303933-4243-f132-f146-423033303933
		 * Manufacturer: Sagemcom
		 * Model: SagemcomFast5656_OFR
		 * Model Number: SG_LBF_1.1.4
		 * Serial Number: LK19302FF
		 * Primary Device Type: 6-0050f204-1
		 * Device name: Livebox Fibre
		 * Config methods: Ethernet, Label
		 * RF Bands: 0x1
		 * Unknown TLV (0x1049, 6 bytes): 00 37 2a 00 01 20
	WMM:	 * Parameter version 1
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
BSS 46:fe:3b:78:6e:18(on wlp0s20f0u2)
	TSF: 1477026656 usec (0d, 00:24:37)
	freq: 5200
	beacon interval: 100 TUs
	capability: ESS Privacy SpectrumMgmt ShortSlotTime (0x0511)
	signal: -80.00 dBm
	last seen: 0 ms ago
	Information elements from Probe Response frame:
	SSID: Livebox-AFB0
	Supported rates: 6.0* 9.0 12.0 18.0 24.0 36.0 48.0 54.0 
	DS Parameter set: channel 40
	BSS Load:
		 * station count: 2
		 * channel utilisation: 6/255
		 * available admission capacity: 65535 [*32us]
	Country: FR	Environment: Indoor/Outdoor
		Channels [36 - 36] @ 23 dBm
		Channels [40 - 40] @ 23 dBm
		Channels [44 - 44] @ 23 dBm
		Channels [48 - 48] @ 23 dBm
		Channels [52 - 52] @ 23 dBm
		Channels [56 - 56] @ 23 dBm
		Channels [60 - 60] @ 23 dBm
		Channels [64 - 64] @ 23 dBm
		Channels [100 - 100] @ 30 dBm
		Channels [104 - 104] @ 30 dBm
		Channels [108 - 108] @ 30 dBm
		Channels [112 - 112] @ 30 dBm
		Channels [116 - 116] @ 30 dBm
		Channels [120 - 120] @ 30 dBm
		Channels [124 - 124] @ 30 dBm
		Channels [128 - 128] @ 30 dBm
	Power constraint: 0 dB
	HT capabilities:
		Capabilities: 0x1ef
			RX LDPC
			HT20/HT40
			SM Power Save disabled
			RX HT20 SGI
			RX HT40 SGI
			TX STBC
			RX STBC 1-stream
			Max AMSDU length: 3839 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 4 usec (0x05)
		HT TX/RX MCS rate indexes supported: 0-31, 33-76
	HT operation:
		 * primary channel: 40
		 * secondary channel offset: below
		 * STA channel width: any
		 * RIFS: 0
		 * HT protection: no
		 * non-GF present: 1
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	WMM:	 * Parameter version 1
		 * u-APSD
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
	RSN:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: PSK
		 * Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
	Extended capabilities:
		 * HT Information Exchange Supported
		 * BSS Transition
		 * SSID List
		 * Operating Mode Notification
		 * Max Number Of MSDUs In A-MSDU is unlimited
	WPS:	 * Version: 1.0
		 * Wi-Fi Protected Setup State: 2 (Configured)
		 * AP setup locked: 0x01
		 * Response Type: 3 (AP)
		 * UUID: 34344645-3342-f738-f645-313834344645
		 * Manufacturer: Arcadyan
		 * Model: WE420244B-OG
		 * Model Number: AR_REP_1.0.0
		 * Serial Number: ASFR84623928
		 * Primary Device Type: 0-00000000-0
		 * Device name:  
		 * Config methods: Ethernet, Label
		 * RF Bands: 0x2
		 * Unknown TLV (0x1049, 6 bytes): 00 37 2a 00 01 20
	VHT capabilities:
		VHT Capabilities (0x3fc379b2):
			Max MPDU length: 11454
			Supported Channel Width: neither 160 nor 80+80
			RX LDPC
			short GI (80 MHz)
			TX STBC
			SU Beamformer
			SU Beamformee
			+HTC-VHT
			RX antenna pattern consistency
			TX antenna pattern consistency
		VHT RX MCS set:
			1 streams: MCS 0-9
			2 streams: MCS 0-9
			3 streams: MCS 0-9
			4 streams: MCS 0-9
			5 streams: not supported
			6 streams: not supported
			7 streams: not supported
			8 streams: not supported
		VHT RX highest supported: 0 Mbps
		VHT TX MCS set:
			1 streams: MCS 0-9
			2 streams: MCS 0-9
			3 streams: MCS 0-9
			4 streams: MCS 0-9
			5 streams: not supported
			6 streams: not supported
			7 streams: not supported
			8 streams: not supported
		VHT TX highest supported: 0 Mbps
	VHT operation:
		 * channel width: 1 (80 MHz)
		 * center freq segment 1: 42
		 * center freq segment 2: 0
		 * VHT basic MCS set: 0xfffc
BSS a4:3e:51:96:41:c5(on wlp0s20f0u2)
	TSF: 1477026660 usec (0d, 00:24:37)
	freq: 5280
	beacon interval: 100 TUs
	capability: ESS Privacy SpectrumMgmt ShortSlotTime (0x0511)
	signal: -84.00 dBm
	last seen: 0 ms ago
	SSID: Livebox-41C0
	Supported rates: 6.0* 9.0 12.0 18.0 24.0 36.0 48.0 54.0 
	DS Parameter set: channel 56
	TIM: DTIM Count 0 DTIM Period 3 Bitmap Control 0x0 Bitmap[0] 0x0
	Country: FR	Environment: Indoor/Outdoor
		Channels [36 - 36] @ 23 dBm
		Channels [40 - 40] @ 23 dBm
		Channels [44 - 44] @ 23 dBm
		Channels [48 - 48] @ 23 dBm
		Channels [52 - 52] @ 23 dBm
		Channels [56 - 56] @ 23 dBm
		Channels [60 - 60] @ 23 dBm
		Channels [64 - 64] @ 23 dBm
		Channels [100 - 100] @ 30 dBm
		Channels [104 - 104] @ 30 dBm
		Channels [108 - 108] @ 30 dBm
		Channels [112 - 112] @ 30 dBm
		Channels [116 - 116] @ 30 dBm
		Channels [120 - 120] @ 30 dBm
		Channels [124 - 124] @ 30 dBm
		Channels [128 - 128] @ 30 dBm
	BSS Load:
		 * station count: 1
		 * channel utilisation: 1/255
		 * available admission capacity: 65535 [*32us]
	Power constraint: 0 dB
	ERP: <no flags>
	HT capabilities:
		Capabilities: 0x1ef
			RX LDPC
			HT20/HT40
			SM Power Save disabled
			RX HT20 SGI
			RX HT40 SGI
			TX STBC
			RX STBC 1-stream
			Max AMSDU length: 3839 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 4 usec (0x05)
		HT TX/RX MCS rate indexes supported: 0-31, 33-76
	HT operation:
		 * primary channel: 56
		 * secondary channel offset: below
		 * STA channel width: any
		 * RIFS: 0
		 * HT protection: no
		 * non-GF present: 1
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	WMM:	 * Parameter version 1
		 * u-APSD
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
	RSN:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: PSK
		 * Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
	VHT capabilities:
		VHT Capabilities (0x3fc379b2):
			Max MPDU length: 11454
			Supported Channel Width: neither 160 nor 80+80
			RX LDPC
			short GI (80 MHz)
			TX STBC
			SU Beamformer
			SU Beamformee
			+HTC-VHT
			RX antenna pattern consistency
			TX antenna pattern consistency
		VHT RX MCS set:
			1 streams: MCS 0-9
			2 streams: MCS 0-9
			3 streams: MCS 0-9
			4 streams: MCS 0-9
			5 streams: not supported
			6 streams: not supported
			7 streams: not supported
			8 streams: not supported
		VHT RX highest supported: 0 Mbps
		VHT TX MCS set:
			1 streams: MCS 0-9
			2 streams: MCS 0-9
			3 streams: MCS 0-9
			4 streams: MCS 0-9
			5 streams: not supported
			6 streams: not supported
			7 streams: not supported
			8 streams: not supported
		VHT TX highest supported: 0 Mbps
	VHT operation:
		 * channel width: 1 (80 MHz)
		 * center freq segment 1: 58
		 * center freq segment 2: 0
		 * VHT basic MCS set: 0xfffc
	Extended capabilities:
		 * HT Information Exchange Supported
		 * BSS Transition
		 * SSID List
		 * Operating Mode Notification
		 * Max Number Of MSDUs In A-MSDU is unlimited
	WPS:	 * Version: 1.0
		 * Wi-Fi Protected Setup State: 2 (Configured)
		 * AP setup locked: 0x01
		 * UUID: 41343345-3531-f936-f431-433041343345
		 * RF Bands: 0x2
		 * Unknown TLV (0x1049, 6 bytes): 00 37 2a 00 01 20
BSS a4:3e:51:96:41:c0(on wlp0s20f0u2)
	TSF: 1477026639 usec (0d, 00:24:37)
	freq: 2412
	beacon interval: 100 TUs
	capability: ESS Privacy ShortSlotTime (0x0411)
	signal: -74.00 dBm
	last seen: 0 ms ago
	Information elements from Probe Response frame:
	SSID: Livebox-41C0
	Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0 
	DS Parameter set: channel 1
	Country: FR	Environment: Indoor/Outdoor
		Channels [1 - 13] @ 20 dBm
	ERP: <no flags>
	Extended supported rates: 6.0 9.0 12.0 48.0 
	RSN:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: PSK
		 * Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
	BSS Load:
		 * station count: 5
		 * channel utilisation: 19/255
		 * available admission capacity: 0 [*32us]
	HT capabilities:
		Capabilities: 0x1ad
			RX LDPC
			HT20
			SM Power Save disabled
			RX HT20 SGI
			TX STBC
			RX STBC 1-stream
			Max AMSDU length: 3839 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 4 usec (0x05)
		HT RX MCS rate indexes supported: 0-23
		HT TX MCS rate indexes are undefined
	HT operation:
		 * primary channel: 1
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 1
		 * HT protection: no
		 * non-GF present: 1
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	Extended capabilities:
		 * Extended Channel Switching
		 * Operating Mode Notification
	WPS:	 * Version: 1.0
		 * Wi-Fi Protected Setup State: 2 (Configured)
		 * Response Type: 3 (AP)
		 * UUID: 41343345-3531-f936-f431-433041343345
		 * Manufacturer: Sercomm
		 * Model: SercommVD836_Livebox4
		 * Model Number: SR_LB4_A.0.7
		 * Serial Number: AH18241FF
		 * Primary Device Type: 6-0050f204-1
		 * Device name: Livebox 4
		 * Config methods: Ethernet, Label
		 * RF Bands: 0x1
		 * Unknown TLV (0x1049, 6 bytes): 00 37 2a 00 01 20
	WMM:	 * Parameter version 1
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
BSS 78:b2:13:89:10:a5(on wlp0s20f0u2)
	TSF: 1477026655 usec (0d, 00:24:37)
	freq: 2462
	beacon interval: 100 TUs
	capability: ESS ShortSlotTime (0x0401)
	signal: -88.00 dBm
	last seen: 0 ms ago
	Information elements from Probe Response frame:
	SSID: orange
	Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0 
	DS Parameter set: channel 11
	Country: FR	Environment: Indoor/Outdoor
		Channels [1 - 13] @ 20 dBm
	ERP: <no flags>
	Extended supported rates: 6.0 9.0 12.0 48.0 
	BSS Load:
		 * station count: 0
		 * channel utilisation: 26/255
		 * available admission capacity: 0 [*32us]
	HT capabilities:
		Capabilities: 0x1ad
			RX LDPC
			HT20
			SM Power Save disabled
			RX HT20 SGI
			TX STBC
			RX STBC 1-stream
			Max AMSDU length: 3839 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 4 usec (0x05)
		HT RX MCS rate indexes supported: 0-23
		HT TX MCS rate indexes are undefined
	HT operation:
		 * primary channel: 11
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 1
		 * HT protection: no
		 * non-GF present: 0
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	Extended capabilities:
		 * Extended Channel Switching
		 * Operating Mode Notification
	WMM:	 * Parameter version 1
		 * u-APSD
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
BSS 78:b2:13:89:10:a9(on wlp0s20f0u2)
	TSF: 1477026661 usec (0d, 00:24:37)
	freq: 5520
	beacon interval: 100 TUs
	capability: ESS Privacy SpectrumMgmt ShortSlotTime (0x0511)
	signal: -82.00 dBm
	last seen: 0 ms ago
	SSID: Livebox-8B98
	Supported rates: 6.0* 9.0 12.0 18.0 24.0 36.0 48.0 54.0 
	DS Parameter set: channel 104
	TIM: DTIM Count 2 DTIM Period 3 Bitmap Control 0x2 Bitmap[0] 0x0 (+ 1 octet)
	Country: FR	Environment: Indoor/Outdoor
		Channels [36 - 36] @ 23 dBm
		Channels [40 - 40] @ 23 dBm
		Channels [44 - 44] @ 23 dBm
		Channels [48 - 48] @ 23 dBm
		Channels [52 - 52] @ 23 dBm
		Channels [56 - 56] @ 23 dBm
		Channels [60 - 60] @ 23 dBm
		Channels [64 - 64] @ 23 dBm
		Channels [100 - 100] @ 30 dBm
		Channels [104 - 104] @ 30 dBm
		Channels [108 - 108] @ 30 dBm
		Channels [112 - 112] @ 30 dBm
		Channels [116 - 116] @ 30 dBm
		Channels [120 - 120] @ 30 dBm
		Channels [124 - 124] @ 30 dBm
		Channels [128 - 128] @ 30 dBm
	BSS Load:
		 * station count: 7
		 * channel utilisation: 11/255
		 * available admission capacity: 65535 [*32us]
	Power constraint: 0 dB
	ERP: <no flags>
	HT capabilities:
		Capabilities: 0x1ef
			RX LDPC
			HT20/HT40
			SM Power Save disabled
			RX HT20 SGI
			RX HT40 SGI
			TX STBC
			RX STBC 1-stream
			Max AMSDU length: 3839 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 4 usec (0x05)
		HT TX/RX MCS rate indexes supported: 0-31, 33-76
	HT operation:
		 * primary channel: 104
		 * secondary channel offset: below
		 * STA channel width: any
		 * RIFS: 0
		 * HT protection: no
		 * non-GF present: 1
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	WMM:	 * Parameter version 1
		 * u-APSD
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
	RSN:	 * Version: 1
		 * Group cipher: TKIP
		 * Pairwise ciphers: CCMP TKIP
		 * Authentication suites: PSK
		 * Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
	WPA:	 * Version: 1
		 * Group cipher: TKIP
		 * Pairwise ciphers: CCMP TKIP
		 * Authentication suites: PSK
	VHT capabilities:
		VHT Capabilities (0x3fc379b2):
			Max MPDU length: 11454
			Supported Channel Width: neither 160 nor 80+80
			RX LDPC
			short GI (80 MHz)
			TX STBC
			SU Beamformer
			SU Beamformee
			+HTC-VHT
			RX antenna pattern consistency
			TX antenna pattern consistency
		VHT RX MCS set:
			1 streams: MCS 0-9
			2 streams: MCS 0-9
			3 streams: MCS 0-9
			4 streams: MCS 0-9
			5 streams: not supported
			6 streams: not supported
			7 streams: not supported
			8 streams: not supported
		VHT RX highest supported: 0 Mbps
		VHT TX MCS set:
			1 streams: MCS 0-9
			2 streams: MCS 0-9
			3 streams: MCS 0-9
			4 streams: MCS 0-9
			5 streams: not supported
			6 streams: not supported
			7 streams: not supported
			8 streams: not supported
		VHT TX highest supported: 0 Mbps
	VHT operation:
		 * channel width: 1 (80 MHz)
		 * center freq segment 1: 106
		 * center freq segment 2: 0
		 * VHT basic MCS set: 0xfffc
	Extended capabilities:
		 * HT Information Exchange Supported
		 * BSS Transition
		 * SSID List
		 * Operating Mode Notification
		 * Max Number Of MSDUs In A-MSDU is unlimited
	WPS:	 * Version: 1.0
		 * Wi-Fi Protected Setup State: 2 (Configured)
		 * AP setup locked: 0x01
		 * UUID: 37384232-3133-f839-f130-413437384232
		 * RF Bands: 0x2
		 * Unknown TLV (0x1049, 6 bytes): 00 37 2a 00 01 20
BSS 44:fe:3b:78:6e:1a(on wlp0s20f0u2)
	TSF: 1477026644 usec (0d, 00:24:37)
	freq: 2412
	beacon interval: 100 TUs
	capability: ESS Privacy ShortSlotTime (0x0411)
	signal: -74.00 dBm
	last seen: 0 ms ago
	Information elements from Probe Response frame:
	SSID: Livebox-AFB0
	Supported rates: 1.0* 2.0* 5.5* 11.0* 6.0 9.0 12.0 18.0 
	DS Parameter set: channel 1
	Country: FR	Environment: Indoor/Outdoor
		Channels [1 - 13] @ 30 dBm
	ERP: <no flags>
	Extended supported rates: 24.0 36.0 48.0 54.0 
	BSS Load:
		 * station count: 0
		 * channel utilisation: 20/255
		 * available admission capacity: 0 [*32us]
	HT capabilities:
		Capabilities: 0x19ad
			RX LDPC
			HT20
			SM Power Save disabled
			RX HT20 SGI
			TX STBC
			RX STBC 1-stream
			Max AMSDU length: 7935 bytes
			DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 16 usec (0x07)
		HT RX MCS rate indexes supported: 0-15
		HT TX MCS rate indexes are undefined
	HT operation:
		 * primary channel: 1
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 0
		 * HT protection: no
		 * non-GF present: 0
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	RSN:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: PSK
		 * Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
	WMM:	 * Parameter version 1
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
	Extended capabilities:
		 * BSS Transition
BSS 30:93:bc:12:af:b5(on wlp0s20f0u2)
	TSF: 1477026658 usec (0d, 00:24:37)
	freq: 5200
	beacon interval: 100 TUs
	capability: ESS Privacy SpectrumMgmt ShortSlotTime RadioMeasure (0x1511)
	signal: -88.00 dBm
	last seen: 0 ms ago
	Information elements from Probe Response frame:
	SSID: Livebox-AFB0
	Supported rates: 6.0* 9.0 12.0 18.0 24.0 36.0 48.0 54.0 
	DS Parameter set: channel 40
	BSS Load:
		 * station count: 4
		 * channel utilisation: 8/255
		 * available admission capacity: 65535 [*32us]
	Country: FR	Environment: Indoor/Outdoor
		Channels [36 - 36] @ 23 dBm
		Channels [40 - 40] @ 23 dBm
		Channels [44 - 44] @ 23 dBm
		Channels [48 - 48] @ 23 dBm
		Channels [52 - 52] @ 23 dBm
		Channels [56 - 56] @ 23 dBm
		Channels [60 - 60] @ 23 dBm
		Channels [64 - 64] @ 23 dBm
		Channels [100 - 100] @ 30 dBm
		Channels [104 - 104] @ 30 dBm
		Channels [108 - 108] @ 30 dBm
		Channels [112 - 112] @ 30 dBm
		Channels [116 - 116] @ 30 dBm
		Channels [120 - 120] @ 30 dBm
		Channels [124 - 124] @ 30 dBm
		Channels [128 - 128] @ 30 dBm
	Power constraint: 0 dB
	HT capabilities:
		Capabilities: 0x1ef
			RX LDPC
			HT20/HT40
			SM Power Save disabled
			RX HT20 SGI
			RX HT40 SGI
			TX STBC
			RX STBC 1-stream
			Max AMSDU length: 3839 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 4 usec (0x05)
		HT TX/RX MCS rate indexes supported: 0-31, 33-76
	HT operation:
		 * primary channel: 40
		 * secondary channel offset: below
		 * STA channel width: any
		 * RIFS: 0
		 * HT protection: nonmember
		 * non-GF present: 1
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	WMM:	 * Parameter version 1
		 * u-APSD
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
	RSN:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: PSK
		 * Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
	Extended capabilities:
		 * HT Information Exchange Supported
		 * BSS Transition
		 * SSID List
		 * Operating Mode Notification
		 * Max Number Of MSDUs In A-MSDU is unlimited
	WPS:	 * Version: 1.0
		 * Wi-Fi Protected Setup State: 2 (Configured)
		 * AP setup locked: 0x01
		 * Response Type: 3 (AP)
		 * UUID: 33303933-4243-f132-f146-423033303933
		 * Manufacturer: Sagemcom
		 * Model: SagemcomFast5656_OFR
		 * Model Number: SG_LBF_1.1.4
		 * Serial Number: LK19302FF
		 * Primary Device Type: 6-0050f204-1
		 * Device name: Livebox Fibre
		 * Config methods: Ethernet, Label
		 * RF Bands: 0x2
		 * Unknown TLV (0x1049, 6 bytes): 00 37 2a 00 01 20
	VHT capabilities:
		VHT Capabilities (0x3fc379b2):
			Max MPDU length: 11454
			Supported Channel Width: neither 160 nor 80+80
			RX LDPC
			short GI (80 MHz)
			TX STBC
			SU Beamformer
			SU Beamformee
			+HTC-VHT
			RX antenna pattern consistency
			TX antenna pattern consistency
		VHT RX MCS set:
			1 streams: MCS 0-9
			2 streams: MCS 0-9
			3 streams: MCS 0-9
			4 streams: MCS 0-9
			5 streams: not supported
			6 streams: not supported
			7 streams: not supported
			8 streams: not supported
		VHT RX highest supported: 0 Mbps
		VHT TX MCS set:
			1 streams: MCS 0-9
			2 streams: MCS 0-9
			3 streams: MCS 0-9
			4 streams: MCS 0-9
			5 streams: not supported
			6 streams: not supported
			7 streams: not supported
			8 streams: not supported
		VHT TX highest supported: 0 Mbps
	VHT operation:
		 * channel width: 1 (80 MHz)
		 * center freq segment 1: 42
		 * center freq segment 2: 0
		 * VHT basic MCS set: 0xfffc
BSS 9e:a3:82:7b:b5:94(on wlp0s20f0u2)
	TSF: 1477026647 usec (0d, 00:24:37)
	freq: 2432
	beacon interval: 100 TUs
	capability: ESS Privacy ShortSlotTime (0x0411)
	signal: -88.00 dBm
	last seen: 0 ms ago
	SSID: FREEBOX_SEVERINE_W8
	Supported rates: 1.0* 2.0* 5.5* 11.0* 9.0 18.0 36.0 54.0 
	DS Parameter set: channel 5
	Extended supported rates: 6.0 12.0 24.0 48.0 
	TIM: DTIM Count 0 DTIM Period 1 Bitmap Control 0x0 Bitmap[0] 0x0
	ERP: Barker_Preamble_Mode
	HT capabilities:
		Capabilities: 0x106e
			HT20/HT40
			SM Power Save disabled
			RX HT20 SGI
			RX HT40 SGI
			No RX STBC
			Max AMSDU length: 3839 bytes
			DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 4 usec (0x05)
		HT RX MCS rate indexes supported: 0-15, 32
		HT TX MCS rate indexes are undefined
	HT operation:
		 * primary channel: 5
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 0
		 * HT protection: 20 MHz
		 * non-GF present: 1
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	Extended capabilities:
		 * HT Information Exchange Supported
	WPA:	 * Version: 1
		 * Group cipher: TKIP
		 * Pairwise ciphers: TKIP CCMP
		 * Authentication suites: PSK
	WMM:	 * Parameter version 1
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
	BSS Load:
		 * station count: 4
		 * channel utilisation: 20/255
		 * available admission capacity: 31250 [*32us]
BSS 9e:a3:82:7b:b5:95(on wlp0s20f0u2)
	TSF: 1477026649 usec (0d, 00:24:37)
	freq: 2432
	beacon interval: 100 TUs
	capability: ESS Privacy ShortSlotTime (0x0411)
	signal: -86.00 dBm
	last seen: 0 ms ago
	SSID: 
	Supported rates: 1.0* 2.0* 5.5* 11.0* 9.0 18.0 36.0 54.0 
	DS Parameter set: channel 5
	Extended supported rates: 6.0 12.0 24.0 48.0 
	TIM: DTIM Count 0 DTIM Period 1 Bitmap Control 0x0 Bitmap[0] 0x0
	ERP: Barker_Preamble_Mode
	HT capabilities:
		Capabilities: 0x106e
			HT20/HT40
			SM Power Save disabled
			RX HT20 SGI
			RX HT40 SGI
			No RX STBC
			Max AMSDU length: 3839 bytes
			DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 4 usec (0x05)
		HT RX MCS rate indexes supported: 0-15, 32
		HT TX MCS rate indexes are undefined
	HT operation:
		 * primary channel: 5
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 0
		 * HT protection: 20 MHz
		 * non-GF present: 1
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	Extended capabilities:
		 * HT Information Exchange Supported
	RSN:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: PSK
		 * Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
	WMM:	 * Parameter version 1
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
	BSS Load:
		 * station count: 4
		 * channel utilisation: 20/255
		 * available admission capacity: 31250 [*32us]
BSS 12:a0:96:7e:42:0f(on wlp0s20f0u2)
	TSF: 1396542485 usec (0d, 00:23:16)
	freq: 2427
	beacon interval: 100 TUs
	capability: ESS Privacy ShortPreamble SpectrumMgmt ShortSlotTime (0x0531)
	signal: -88.00 dBm
	last seen: 0 ms ago
	Information elements from Probe Response frame:
	SSID: DIRECT-Up-BRAVIA
	Supported rates: 6.0* 9.0 12.0* 18.0 24.0* 36.0 48.0 54.0 
	DS Parameter set: channel 4
	Power constraint: 0 dB
	ERP: <no flags>
	RSN:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: PSK
		 * Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
	HT capabilities:
		Capabilities: 0x12c
			HT20
			SM Power Save disabled
			RX HT20 SGI
			RX STBC 1-stream
			Max AMSDU length: 3839 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 8 usec (0x06)
		HT RX MCS rate indexes supported: 0-7
		HT TX MCS rate indexes are undefined
	HT operation:
		 * primary channel: 4
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 1
		 * HT protection: no
		 * non-GF present: 0
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	Overlapping BSS scan params:
		 * passive dwell: 20 TUs
		 * active dwell: 10 TUs
		 * channel width trigger scan interval: 300 s
		 * scan passive total per channel: 200 TUs
		 * scan active total per channel: 20 TUs
		 * BSS width channel transition delay factor: 5
		 * OBSS Scan Activity Threshold: 0.25 %
	Extended capabilities:
		 * HT Information Exchange Supported
	WMM:	 * Parameter version 1
		 * u-APSD
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
	WPS:	 * Version: 1.0
		 * Wi-Fi Protected Setup State: 2 (Configured)
		 * Response Type: 3 (AP)
		 * UUID: 00000000-0000-1010-8000-00a0967e420f
		 * Manufacturer: Sony Corporation
		 * Model: Sony BRAVIA
		 * Model Number: 0
		 * Serial Number: 0
		 * Primary Device Type: 7-0050f204-1
		 * Device name: BRAVIA KDL-55HX750
		 * Config methods:
		 * RF Bands: 0x1
		 * Unknown TLV (0x1049, 6 bytes): 00 37 2a 00 01 20
BSS 78:b2:13:89:10:a4(on wlp0s20f0u2)
	TSF: 1477026653 usec (0d, 00:24:37)
	freq: 2462
	beacon interval: 100 TUs
	capability: ESS Privacy ShortSlotTime (0x0411)
	signal: -88.00 dBm
	last seen: 0 ms ago
	Information elements from Probe Response frame:
	SSID: Livebox-8B98
	Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0 
	DS Parameter set: channel 11
	Country: FR	Environment: Indoor/Outdoor
		Channels [1 - 13] @ 20 dBm
	ERP: <no flags>
	Extended supported rates: 6.0 9.0 12.0 48.0 
	RSN:	 * Version: 1
		 * Group cipher: TKIP
		 * Pairwise ciphers: CCMP TKIP
		 * Authentication suites: PSK
		 * Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
	BSS Load:
		 * station count: 0
		 * channel utilisation: 26/255
		 * available admission capacity: 0 [*32us]
	HT capabilities:
		Capabilities: 0x1ad
			RX LDPC
			HT20
			SM Power Save disabled
			RX HT20 SGI
			TX STBC
			RX STBC 1-stream
			Max AMSDU length: 3839 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 4 usec (0x05)
		HT RX MCS rate indexes supported: 0-23
		HT TX MCS rate indexes are undefined
	HT operation:
		 * primary channel: 11
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 1
		 * HT protection: no
		 * non-GF present: 0
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	Extended capabilities:
		 * Extended Channel Switching
		 * Operating Mode Notification
	WPS:	 * Version: 1.0
		 * Wi-Fi Protected Setup State: 2 (Configured)
		 * Response Type: 3 (AP)
		 * UUID: 37384232-3133-f839-f130-413437384232
		 * Manufacturer: Sercomm
		 * Model: SercommVD836_Livebox4
		 * Model Number: SR_LB4_A.0.8
		 * Serial Number: FBKL001FF
		 * Primary Device Type: 6-0050f204-1
		 * Device name: Livebox 4
		 * Config methods: Ethernet, Label
		 * RF Bands: 0x1
		 * Unknown TLV (0x1049, 6 bytes): 00 37 2a 00 01 20
	WPA:	 * Version: 1
		 * Group cipher: TKIP
		 * Pairwise ciphers: CCMP TKIP
		 * Authentication suites: PSK
	WMM:	 * Parameter version 1
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
BSS 9e:a3:82:7b:b5:96(on wlp0s20f0u2)
	TSF: 1477026650 usec (0d, 00:24:37)
	freq: 2432
	beacon interval: 100 TUs
	capability: ESS Privacy ShortSlotTime (0x0411)
	signal: -86.00 dBm
	last seen: 0 ms ago
	SSID: FreeWifi_secure
	Supported rates: 1.0* 2.0* 5.5* 11.0* 9.0 18.0 36.0 54.0 
	DS Parameter set: channel 5
	Extended supported rates: 6.0 12.0 24.0 48.0 
	TIM: DTIM Count 0 DTIM Period 1 Bitmap Control 0x0 Bitmap[0] 0x0
	ERP: Barker_Preamble_Mode
	HT capabilities:
		Capabilities: 0x106e
			HT20/HT40
			SM Power Save disabled
			RX HT20 SGI
			RX HT40 SGI
			No RX STBC
			Max AMSDU length: 3839 bytes
			DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 4 usec (0x05)
		HT RX MCS rate indexes supported: 0-15, 32
		HT TX MCS rate indexes are undefined
	HT operation:
		 * primary channel: 5
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 0
		 * HT protection: 20 MHz
		 * non-GF present: 1
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	Extended capabilities:
		 * HT Information Exchange Supported
	WPA:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: IEEE 802.1X
	WMM:	 * Parameter version 1
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
	BSS Load:
		 * station count: 4
		 * channel utilisation: 20/255
		 * available admission capacity: 31250 [*32us]
/code]
La connaîssance n'a pas de limite.
Mais sa valeur, est d'autant plus grande, une fois partagé


Pc fixe --- MSI MPG Z490 Gaming Edge WiFi, I9-9900Kf, RTX3070Ti, 64Go DDR4, SSD 1Tera nvme gen4 Samsung 980 pro, SSD 1Tera WD Blacksn850X,3HDD 5Tera
Eeepc Asus 1015pem --- Intel Atom N550 Dual-core 1.5Ghz / DD 1Tera 7200rpm / Ram 2Go

Screenshot + Les Conky ===> http://forums.archlinux.fr/post85405.html#p85405
Avatar de l’utilisateur
benjarobin
Maître du Kyudo
Messages : 17187
Inscription : sam. 30 mai 2009, 15:48
Localisation : Lyon

Re: [Connexion Wifi] Installation Wifi (en cours)

Message par benjarobin »

Juste pour savoir, as tu bien renommé le nom du Wifi comme préconisé ? Le vois tu sur tes autres appareils ?
Car je vois bien un Wifi caché dans la liste... D’ailleurs le FreeWifi visible est dans le même canal...
Zsh | KDE | PC fixe : core i7, carte nvidia
Titre d'un sujet : [Thème] Sujet (état) / Règles du forum
Avatar de l’utilisateur
banditblue
Elfe
Messages : 591
Inscription : dim. 10 janv. 2010, 10:19

Re: [Connexion Wifi] Installation Wifi (en cours)

Message par banditblue »

j'ai bien renommé le nouveau SSID mais rien n'est visible
La connaîssance n'a pas de limite.
Mais sa valeur, est d'autant plus grande, une fois partagé


Pc fixe --- MSI MPG Z490 Gaming Edge WiFi, I9-9900Kf, RTX3070Ti, 64Go DDR4, SSD 1Tera nvme gen4 Samsung 980 pro, SSD 1Tera WD Blacksn850X,3HDD 5Tera
Eeepc Asus 1015pem --- Intel Atom N550 Dual-core 1.5Ghz / DD 1Tera 7200rpm / Ram 2Go

Screenshot + Les Conky ===> http://forums.archlinux.fr/post85405.html#p85405
Avatar de l’utilisateur
banditblue
Elfe
Messages : 591
Inscription : dim. 10 janv. 2010, 10:19

Re: [Connexion Wifi] Installation Wifi (en cours)

Message par banditblue »

j'utilise cette ligne de commande pour faire le scan et l'ecrire dans un fichier
sudo iw dev wlp0s20f0u2 scan > /home/moi/list_scan_wifi_00
La connaîssance n'a pas de limite.
Mais sa valeur, est d'autant plus grande, une fois partagé


Pc fixe --- MSI MPG Z490 Gaming Edge WiFi, I9-9900Kf, RTX3070Ti, 64Go DDR4, SSD 1Tera nvme gen4 Samsung 980 pro, SSD 1Tera WD Blacksn850X,3HDD 5Tera
Eeepc Asus 1015pem --- Intel Atom N550 Dual-core 1.5Ghz / DD 1Tera 7200rpm / Ram 2Go

Screenshot + Les Conky ===> http://forums.archlinux.fr/post85405.html#p85405
Avatar de l’utilisateur
benjarobin
Maître du Kyudo
Messages : 17187
Inscription : sam. 30 mai 2009, 15:48
Localisation : Lyon

Re: [Connexion Wifi] Installation Wifi (en cours)

Message par benjarobin »

Note: Je t'ai envoyé un message privé
Zsh | KDE | PC fixe : core i7, carte nvidia
Titre d'un sujet : [Thème] Sujet (état) / Règles du forum
Avatar de l’utilisateur
banditblue
Elfe
Messages : 591
Inscription : dim. 10 janv. 2010, 10:19

Re: [Connexion Wifi] Installation Wifi (en cours)

Message par banditblue »

Pour faire suite apre moins d'une heure avec benjarobin au telephone, contact fort sympatique, ravie d'avoir eu un echange avec toi

En ce debut d'apres-midi, je rallume mon pc puis je configure en mode graphique ma connection WIFI, j'arrive a obtenir ces informations
a quoi dois-je m'attendre ? est ce connecté en wifi ?
Image
La connaîssance n'a pas de limite.
Mais sa valeur, est d'autant plus grande, une fois partagé


Pc fixe --- MSI MPG Z490 Gaming Edge WiFi, I9-9900Kf, RTX3070Ti, 64Go DDR4, SSD 1Tera nvme gen4 Samsung 980 pro, SSD 1Tera WD Blacksn850X,3HDD 5Tera
Eeepc Asus 1015pem --- Intel Atom N550 Dual-core 1.5Ghz / DD 1Tera 7200rpm / Ram 2Go

Screenshot + Les Conky ===> http://forums.archlinux.fr/post85405.html#p85405
Avatar de l’utilisateur
benjarobin
Maître du Kyudo
Messages : 17187
Inscription : sam. 30 mai 2009, 15:48
Localisation : Lyon

Re: [Connexion Wifi] Installation Wifi (en cours)

Message par benjarobin »

Je crains que n'ai créé un hotspot... Tu peux éteindre la Freebox, et tu devrais voir le réseau wifi que tu as créé avec ton smartphone.

Si tu veux créé manuellement la connexion, tu dois remplir les champs suivants :
- Général : cocher tous les utilisateurs peuvent se connecter à ce réseau
- SSID : le nom de ton réseau wifi
- Mode : Client
- Bande : Automatique
- Périphérique : tu sélectionnes dans le menu déroulant ta carte wifi
- sécurité : wpa et wpa2 personnel
- mot de passe : la clé du wifi
- Tout le reste est normalement par défaut
Zsh | KDE | PC fixe : core i7, carte nvidia
Titre d'un sujet : [Thème] Sujet (état) / Règles du forum
Avatar de l’utilisateur
banditblue
Elfe
Messages : 591
Inscription : dim. 10 janv. 2010, 10:19

Re: [Connexion Wifi] Installation Wifi (en cours)

Message par banditblue »

Petite question, pour que ma clef usb3 wifi de chez ASUS fonctionnent.

je vais peut etre m'aventurer sur un terrain inconnue
Ne dois t'on pas recompiler le kernel noyau avec les nouveaux drivers ?

Image
La connaîssance n'a pas de limite.
Mais sa valeur, est d'autant plus grande, une fois partagé


Pc fixe --- MSI MPG Z490 Gaming Edge WiFi, I9-9900Kf, RTX3070Ti, 64Go DDR4, SSD 1Tera nvme gen4 Samsung 980 pro, SSD 1Tera WD Blacksn850X,3HDD 5Tera
Eeepc Asus 1015pem --- Intel Atom N550 Dual-core 1.5Ghz / DD 1Tera 7200rpm / Ram 2Go

Screenshot + Les Conky ===> http://forums.archlinux.fr/post85405.html#p85405
Répondre