[bluetooth] Asus EEEpc 1201HA (le retour!) [abandonné]

Reconnaissance et configuration du matériel / kernel linux
Répondre
Blabladodo
Hankyu
Messages : 37
Inscription : mer. 04 nov. 2015, 14:10
Localisation : Montpellier

[bluetooth] Asus EEEpc 1201HA (le retour!) [abandonné]

Message par Blabladodo »

Bonsoir à vous,


Je poste ici ce soir, un peu en suite de mon précédent post sur cet ordinateur, à propos du chipset bluetooth (voir par ici).
J'ai voulu faire un petit test ; cette après-midi j'ai changé la carte pci-e sans fil de ce netbook par celle d'un autre portable que j'ai à ma disposition (MSI ge60 2PL) : la carte semble être acceptée, le bios ne bronche pas, Archlinux détecte bien la nouvelle carte wifi dans lspci (01:00.0 Network controller: Intel Corporation Wireless 3160 (rev 83)) ... Mais toujours pas de trace de bluetooth (rfkill list et hcitool dev ne me retournent rien de concluant), et cette fois je sais que la carte pci-e dispose d'un chipset bluetooth !

Je ne sais pas trop quoi filer comme infos :

Code : Tout sélectionner

lspci
00:00.0 Host bridge: Intel Corporation System Controller Hub (SCH Poulsbo) (rev 07)
00:02.0 VGA compatible controller: Intel Corporation System Controller Hub (SCH Poulsbo) Graphics Controller (rev 07)
00:1b.0 Audio device: Intel Corporation System Controller Hub (SCH Poulsbo) HD Audio Controller (rev 07)
00:1c.0 PCI bridge: Intel Corporation System Controller Hub (SCH Poulsbo) PCI Express Port 1 (rev 07)
00:1c.1 PCI bridge: Intel Corporation System Controller Hub (SCH Poulsbo) PCI Express Port 2 (rev 07)
00:1d.0 USB controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #1 (rev 07)
00:1d.1 USB controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #2 (rev 07)
00:1d.2 USB controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #3 (rev 07)
00:1d.7 USB controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB EHCI #1 (rev 07)
00:1f.0 ISA bridge: Intel Corporation System Controller Hub (SCH Poulsbo) LPC Bridge (rev 07)
00:1f.1 IDE interface: Intel Corporation System Controller Hub (SCH Poulsbo) IDE Controller (rev 07)
01:00.0 Network controller: Intel Corporation Wireless 3160 (rev 83)
03:00.0 Ethernet controller: Qualcomm Atheros AR8132 Fast Ethernet (rev c0)

sudo rfkill list
0: eeepc-wlan: Wireless LAN
	Soft blocked: no
	Hard blocked: no
1: phy0: Wireless LAN
	Soft blocked: no
	Hard blocked: no

sudo hcitool dev
Devices:

uname -a
Linux archlinux-ASUS-netbook 4.4.6-1-ck #1 SMP PREEMPT Fri Mar 25 18:43:19 EDT 2016 i686 GNU/Linux
Des suggestions ? Peut-être une mauvaise gestion au niveau du BIOS ? Je suis preneur de toutes pistes que vous pourrez me donner :) Merci par avance.
Je suis allé voir du côté des réglages BIOS, je n'ai rien vu qui semblait pouvoir m'aider de ce côté là (si besoin je prendrais des photos des différents écrans).

(J'ai un peu l'air d'un maniaque avec cette histoire de bluetooth, mais j'aime bien que tout ce dont est équipé ma machine fonctionne, à plus forte raison que je pourrais avoir usage de bluetooth tout particulièrement sur cette machine)
Dernière modification par Blabladodo le mar. 12 avr. 2016, 12:45, modifié 1 fois.
Xiaomi Notebook Pro i5/8 Gb - Archlinux/Plasma, kernel stock, Bumblebee (Nvidia)
Macbook Pro 8.2 - Archlinux/Plasma, kernel linux-macbook, Intel only.
HP Pavilion g6 1354ef - Archlinux/XFCE, kernel ck-sandybridge
Avatar de l’utilisateur
benjarobin
Maître du Kyudo
Messages : 17235
Inscription : sam. 30 mai 2009, 15:48
Localisation : Lyon

Re: [bluetooth] Asus EEEpc 1201HA (le retour!)

Message par benjarobin »

Bonjour, la sortie de dmesg pourrait aider, enfin j'espère
Zsh | KDE | PC fixe : core i7, carte nvidia
Titre d'un sujet : [Thème] Sujet (état) / Règles du forum
Blabladodo
Hankyu
Messages : 37
Inscription : mer. 04 nov. 2015, 14:10
Localisation : Montpellier

Re: [bluetooth] Asus EEEpc 1201HA (le retour!)

Message par Blabladodo »

Bonjour, merci pour ta réponse.

Voici un dmesg datant d'hier soir (j'avais commencé moi même à regarder dedans, rien trouvé de probant pour le moment mais je ne suis pas allé jusqu'au bout), commande lancé juste après l'ouverture de session et l'ouverture du terminal.

Code : Tout sélectionner

dmesg
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Linux version 4.4.6-1-ck (squishy@waste) (gcc version 5.3.0 (GCC) ) #1 SMP PREEMPT Fri Mar 25 18:43:19 EDT 2016
[    0.000000] Disabled fast string operations
[    0.000000] x86/fpu: Legacy x87 FPU detected.
[    0.000000] x86/fpu: Using 'lazy' FPU context switches.
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e2000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007f64ffff] usable
[    0.000000] BIOS-e820: [mem 0x000000007f650000-0x000000007f65ffff] reserved
[    0.000000] BIOS-e820: [mem 0x000000007f660000-0x000000007f66dfff] ACPI data
[    0.000000] BIOS-e820: [mem 0x000000007f66e000-0x000000007f6affff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x000000007f6b0000-0x000000007f6bffff] reserved
[    0.000000] BIOS-e820: [mem 0x000000007f6c8000-0x000000007f7fffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fff00000-0x00000000ffffffff] reserved
[    0.000000] e820: remove [mem 0x78000000-0xfffffffffffffffe] usable
[    0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
[    0.000000] e820: user-defined physical RAM map:
[    0.000000] user: [mem 0x0000000000000000-0x000000000009fbff] usable
[    0.000000] user: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[    0.000000] user: [mem 0x00000000000e2000-0x00000000000fffff] reserved
[    0.000000] user: [mem 0x0000000000100000-0x0000000077ffffff] usable
[    0.000000] user: [mem 0x000000007f650000-0x000000007f65ffff] reserved
[    0.000000] user: [mem 0x000000007f660000-0x000000007f66dfff] ACPI data
[    0.000000] user: [mem 0x000000007f66e000-0x000000007f6affff] ACPI NVS
[    0.000000] user: [mem 0x000000007f6b0000-0x000000007f6bffff] reserved
[    0.000000] user: [mem 0x000000007f6c8000-0x000000007f7fffff] reserved
[    0.000000] user: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] user: [mem 0x00000000fff00000-0x00000000ffffffff] reserved
[    0.000000] SMBIOS 2.5 present.
[    0.000000] DMI: ASUSTeK Computer INC. 1201HA/1201HA, BIOS 0303    04/15/2010
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] e820: last_pfn = 0x78000 max_arch_pfn = 0x100000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-DFFFF uncachable
[    0.000000]   E0000-EFFFF write-through
[    0.000000]   F0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask 080000000 write-back
[    0.000000]   1 base 07F700000 mask 0FFF00000 uncachable
[    0.000000]   2 base 07F800000 mask 0FF800000 uncachable
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WC  UC- WT  
[    0.000000] found SMP MP-table at [mem 0x000ff780-0x000ff78f] mapped at [c00ff780]
[    0.000000] Scanning 1 areas for low memory corruption
[    0.000000] initial memory mapped: [mem 0x00000000-0x01bfffff]
[    0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[    0.000000] BRK [0x01840000, 0x01840fff] PGTABLE
[    0.000000] RAMDISK: [mem 0x3777a000-0x37bb4fff]
[    0.000000] Allocated new RAMDISK: [mem 0x3733f000-0x3777927b]
[    0.000000] Move RAMDISK from [mem 0x3777a000-0x37bb427b] to [mem 0x3733f000-0x3777927b]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000FBFD0 000024 (v02 ACPIAM)
[    0.000000] ACPI: XSDT 0x000000007F660100 000064 (v01 _ASUS_ Notebook 20100415 MSFT 00000097)
[    0.000000] ACPI: FACP 0x000000007F660290 0000F4 (v04 041510 FACP1112 20100415 MSFT 00000097)
[    0.000000] ACPI: DSDT 0x000000007F660430 009643 (v02 A1451  A1451000 00000000 INTL 20060113)
[    0.000000] ACPI: FACS 0x000000007F66E000 000040
[    0.000000] ACPI: FACS 0x000000007F66E000 000040
[    0.000000] ACPI: APIC 0x000000007F660390 00005C (v02 041510 APIC1112 20100415 MSFT 00000097)
[    0.000000] ACPI: MCFG 0x000000007F6603F0 00003C (v01 041510 OEMMCFG  20100415 MSFT 00000097)
[    0.000000] ACPI: OEMB 0x000000007F66E040 00012C (v01 041510 OEMB1112 20100415 MSFT 00000097)
[    0.000000] ACPI: HPET 0x000000007F669A80 000038 (v01 041510 OEMHPET  20100415 MSFT 00000097)
[    0.000000] ACPI: GSCI 0x000000007F66E170 002024 (v01 041510 GMCHSCI  20100415 MSFT 00000097)
[    0.000000] ACPI: SSDT 0x000000007F670B60 0004F0 (v01 PmRef  CpuPm    00003000 INTL 20060113)
[    0.000000] ACPI: SLIC 0x000000007F669AC0 000176 (v01 _ASUS_ Notebook 20100415 MSFT 00000097)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 1032MB HIGHMEM available.
[    0.000000] 887MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 377fe000
[    0.000000]   low ram: 0 - 377fe000
[    0.000000] BRK [0x01841000, 0x01841fff] PGTABLE
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.000000]   Normal   [mem 0x0000000001000000-0x00000000377fdfff]
[    0.000000]   HighMem  [mem 0x00000000377fe000-0x0000000077ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000001000-0x000000000009efff]
[    0.000000]   node   0: [mem 0x0000000000100000-0x0000000077ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x0000000077ffffff]
[    0.000000] On node 0 totalpages: 491422
[    0.000000] free_area_init_node: node 0, pgdat c16b32c0, node_mem_map f607f028
[    0.000000]   DMA zone: 40 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3998 pages, LIFO batch:0
[    0.000000]   Normal zone: 2180 pages used for memmap
[    0.000000]   Normal zone: 223230 pages, LIFO batch:31
[    0.000000]   HighMem zone: 264194 pages, LIFO batch:31
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x908
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
[    0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000e1fff]
[    0.000000] PM: Registered nosave memory: [mem 0x000e2000-0x000fffff]
[    0.000000] e820: [mem 0x7f800000-0xfedfffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns
[    0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
[    0.000000] PERCPU: Embedded 17 pages/cpu @f77d0000 s38860 r0 d30772 u69632
[    0.000000] pcpu-alloc: s38860 r0 d30772 u69632 alloc=17*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 489202
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux-ck root=UUID=e9d5c28a-c0b5-49d0-bc3f-831afb6c53a2 rw mem=1920mb quiet resume=UUID=a8300492-dceb-4a08-8e36-8df309a6b2ad acpi_backlight=vendor acpi_osi=Linux asus_wmi.blacklist=yes
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] microcode: CPU0 microcode updated early to revision 0x217, date = 2009-04-10
[    0.000000] Initializing CPU#0
[    0.000000] Initializing HighMem for node 0 (000377fe:00078000)
[    0.000000] Initializing Movable for node 0 (00000000:00000000)
[    0.000000] Memory: 1932644K/1965688K available (5014K kernel code, 516K rwdata, 1408K rodata, 612K init, 832K bss, 33044K reserved, 0K cma-reserved, 1056776K highmem)
[    0.000000] virtual kernel memory layout:
                   fixmap  : 0xfff16000 - 0xfffff000   ( 932 kB)
                   pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
                   vmalloc : 0xf7ffe000 - 0xff7fe000   ( 120 MB)
                   lowmem  : 0xc0000000 - 0xf77fe000   ( 887 MB)
                     .init : 0xc16ca000 - 0xc1763000   ( 612 kB)
                     .data : 0xc14e5b82 - 0xc16c82c0   (1929 kB)
                     .text : 0xc1000000 - 0xc14e5b82   (5014 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Build-time adjustment of leaf fanout to 32.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
[    0.000000] NR_IRQS:2304 nr_irqs:440 16
[    0.000000] CPU 0 irqstacks, hard=f5834000 soft=f5836000
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 1331.302 MHz processor
[    0.001024] Calibrating delay loop (skipped), value calculated using timer frequency.. 2662.60 BogoMIPS (lpj=1331302)
[    0.001036] pid_max: default: 32768 minimum: 301
[    0.002021] ACPI: Core revision 20150930
[    0.027181] ACPI: 2 ACPI AML tables successfully acquired and loaded
[    0.027241] Security Framework initialized
[    0.027249] Yama: becoming mindful.
[    0.027288] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.027297] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.027886] Initializing cgroup subsys io
[    0.027904] Initializing cgroup subsys memory
[    0.027928] Initializing cgroup subsys devices
[    0.027939] Initializing cgroup subsys freezer
[    0.027949] Initializing cgroup subsys net_cls
[    0.027959] Initializing cgroup subsys pids
[    0.028026] Disabled fast string operations
[    0.028034] CPU: Physical Processor ID: 0
[    0.028039] CPU: Processor Core ID: 0
[    0.028051] mce: CPU supports 5 MCE banks
[    0.028070] CPU0: Thermal monitoring enabled (TM2)
[    0.028081] process: using mwait in idle threads
[    0.028099] Last level iTLB entries: 4KB 32, 2MB 0, 4MB 0
[    0.028105] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 8, 1GB 0
[    0.028475] Freeing SMP alternatives memory: 20K (c1763000 - c1768000)
[    0.031031] ftrace: allocating 21348 entries in 42 pages
[    0.045206] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.046319] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.057000] smpboot: CPU0: Intel(R) Atom(TM) CPU Z520   @ 1.33GHz (family: 0x6, model: 0x1c, stepping: 0x2)
[    0.057000] Performance Events: PEBS fmt0+, LBR disabled due to erratumAtom events, Intel PMU driver.
[    0.057000] ... version:                3
[    0.057000] ... bit width:              40
[    0.057000] ... generic registers:      2
[    0.057000] ... value mask:             000000ffffffffff
[    0.057000] ... max period:             000000007fffffff
[    0.057000] ... fixed-purpose events:   3
[    0.057000] ... event mask:             0000000700000003
[    0.062108] CPU 1 irqstacks, hard=f5944000 soft=f5946000
[    0.062118] x86: Booting SMP configuration:
[    0.062124] .... node  #0, CPUs:      #1
[    0.060043] Initializing CPU#1
[    0.060043] Disabled fast string operations
[    0.063336] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.063330] x86: Booted up 1 node, 2 CPUs
[    0.063339] smpboot: Total of 2 processors activated (5325.20 BogoMIPS)
[    0.064132] BFS LOCALITY CPU 0 to 1: 1
[    0.064411] devtmpfs: initialized
[    0.065571] PM: Registering ACPI NVS region [mem 0x7f66e000-0x7f6affff] (270336 bytes)
[    0.066018] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[    0.066225] pinctrl core: initialized pinctrl subsystem
[    0.066330] RTC time: 18:44:56, date: 03/27/16
[    0.066757] NET: Registered protocol family 16
[    0.070015] cpuidle: using governor ladder
[    0.074014] cpuidle: using governor menu
[    0.074293] ACPI: bus type PCI registered
[    0.074302] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.074589] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.074598] PCI: not using MMCONFIG
[    0.075122] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=3
[    0.075127] PCI: Using configuration type 1 for base access
[    0.083035] ACPI: Added _OSI(Module Device)
[    0.083047] ACPI: Added _OSI(Processor Device)
[    0.083053] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.083059] ACPI: Added _OSI(Processor Aggregator Device)
[    0.083065] ACPI: Added _OSI(Linux)
[    0.092210] ACPI: Executed 1 blocks of module-level executable AML code
[    0.103594] ACPI: Dynamic OEM Table Load:
[    0.103617] ACPI: SSDT 0x00000000F5A24600 0001FA (v01 PmRef  Cpu0Ist  00003000 INTL 20060113)
[    0.105248] ACPI: Dynamic OEM Table Load:
[    0.105270] ACPI: SSDT 0x00000000F5812000 00065D (v01 PmRef  Cpu0Cst  00003001 INTL 20060113)
[    0.107606] ACPI: Dynamic OEM Table Load:
[    0.107622] ACPI: SSDT 0x00000000F59F0700 0000CC (v01 PmRef  Cpu1Ist  00003000 INTL 20060113)
[    0.109013] ACPI: Dynamic OEM Table Load:
[    0.109028] ACPI: SSDT 0x00000000F5A0B0C0 000085 (v01 PmRef  Cpu1Cst  00003000 INTL 20060113)
[    0.110767] ACPI : EC: EC started
[    0.111206] ACPI: Interpreter enabled
[    0.111242] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20150930/hwxface-580)
[    0.111257] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20150930/hwxface-580)
[    0.111306] ACPI: (supports S0 S3 S4 S5)
[    0.111313] ACPI: Using IOAPIC for interrupt routing
[    0.111448] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.115496] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[    0.115503] PCI: Using MMCONFIG for extended config space
[    0.115520] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.129906] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query honored via cmdline
[    0.135023] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.135046] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.135065] acpi PNP0A08:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[    0.135800] PCI host bridge to bus 0000:00
[    0.135812] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.135821] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.135829] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.135837] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000dffff window]
[    0.135846] pci_bus 0000:00: root bus resource [mem 0x7f800000-0xdfffffff window]
[    0.135854] pci_bus 0000:00: root bus resource [mem 0xf0000000-0xffffffff window]
[    0.135862] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.135890] pci 0000:00:00.0: [8086:8100] type 00 class 0x060000
[    0.136254] pci 0000:00:02.0: [8086:8108] type 00 class 0x030000
[    0.136298] pci 0000:00:02.0: reg 0x10: [mem 0xf3f80000-0xf3ffffff]
[    0.136315] pci 0000:00:02.0: reg 0x14: [io  0xd880-0xd887]
[    0.136331] pci 0000:00:02.0: reg 0x18: [mem 0xd0000000-0xdfffffff]
[    0.136347] pci 0000:00:02.0: reg 0x1c: [mem 0xf3f40000-0xf3f7ffff]
[    0.136721] pci 0000:00:1c.0: [8086:8110] type 01 class 0x060400
[    0.136817] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.136941] pci 0000:00:1c.0: System wakeup disabled by ACPI
[    0.137163] pci 0000:00:1c.1: [8086:8112] type 01 class 0x060400
[    0.137264] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.137386] pci 0000:00:1c.1: System wakeup disabled by ACPI
[    0.137599] pci 0000:00:1d.0: [8086:8114] type 00 class 0x0c0300
[    0.137655] pci 0000:00:1d.0: reg 0x20: [io  0xc880-0xc89f]
[    0.137854] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    0.138068] pci 0000:00:1d.1: [8086:8115] type 00 class 0x0c0300
[    0.138126] pci 0000:00:1d.1: reg 0x20: [io  0xd080-0xd09f]
[    0.138319] pci 0000:00:1d.1: System wakeup disabled by ACPI
[    0.138528] pci 0000:00:1d.2: [8086:8116] type 00 class 0x0c0300
[    0.138585] pci 0000:00:1d.2: reg 0x20: [io  0xd480-0xd49f]
[    0.138778] pci 0000:00:1d.2: System wakeup disabled by ACPI
[    0.138987] pci 0000:00:1d.7: [8086:8117] type 00 class 0x0c0320
[    0.139050] pci 0000:00:1d.7: reg 0x10: [mem 0xf3f37c00-0xf3f37fff]
[    0.139180] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.139306] pci 0000:00:1d.7: System wakeup disabled by ACPI
[    0.139512] pci 0000:00:1f.0: [8086:8119] type 00 class 0x060100
[    0.139864] pci 0000:00:1f.1: [8086:811a] type 00 class 0x010180
[    0.139923] pci 0000:00:1f.1: reg 0x20: [io  0xffa0-0xffaf]
[    0.139951] pci 0000:00:1f.1: legacy IDE quirk: reg 0x10: [io  0x01f0-0x01f7]
[    0.139958] pci 0000:00:1f.1: legacy IDE quirk: reg 0x14: [io  0x03f6]
[    0.139966] pci 0000:00:1f.1: legacy IDE quirk: reg 0x18: [io  0x0170-0x0177]
[    0.139973] pci 0000:00:1f.1: legacy IDE quirk: reg 0x1c: [io  0x0376]
[    0.140397] pci 0000:00:1c.0: PCI bridge to [bus 03]
[    0.140611] pci 0000:01:00.0: [8086:08b3] type 00 class 0x028000
[    0.140696] pci 0000:01:00.0: reg 0x10: [mem 0xfbffe000-0xfbffffff 64bit]
[    0.140900] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    0.143042] pci 0000:00:1c.1: PCI bridge to [bus 01-02]
[    0.143055] pci 0000:00:1c.1:   bridge window [io  0xe000-0xefff]
[    0.143066] pci 0000:00:1c.1:   bridge window [mem 0xf4000000-0xfbffffff]
[    0.143076] pci 0000:00:1c.1:   bridge window [mem 0xcc000000-0xcfffffff pref]
[    0.143099] pci_bus 0000:00: on NUMA node 0
[    0.145782] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[    0.146021] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[    0.146240] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
[    0.146466] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15)
[    0.146683] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 *4 5 6 7 10 11 12 14 15)
[    0.146900] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 *7 10 11 12 14 15)
[    0.147134] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.147351] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 *6 7 10 11 12 14 15)
[    0.147596] ACPI: Enabled 2 GPEs in block 00 to 1F
[    0.147820] ACPI : EC: GPE = 0xd, I/O: command/status = 0x66, data = 0x62
[    0.148179] vgaarb: setting as boot device: PCI:0000:00:02.0
[    0.148188] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    0.148199] vgaarb: loaded
[    0.148204] vgaarb: bridge control possible 0000:00:02.0
[    0.148519] PCI: Using ACPI for IRQ routing
[    0.148601] PCI: pci_cache_line_size set to 64 bytes
[    0.148661] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[    0.149218] NetLabel: Initializing
[    0.149225] NetLabel:  domain hash size = 128
[    0.149229] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.149267] NetLabel:  unlabeled traffic allowed by default
[    0.149436] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.149447] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.149460] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.151109] clocksource: Switched to clocksource hpet
[    0.175003] pnp: PnP ACPI init
[    0.175638] system 00:00: [mem 0x7f800000-0x7fffffff] has been reserved
[    0.175656] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.175826] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.176075] pnp 00:02: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[    0.176632] system 00:03: [io  0x0374-0x0375] has been reserved
[    0.176643] system 00:03: [io  0x03f4-0x03f5] has been reserved
[    0.176652] system 00:03: [io  0x0380-0x0387] has been reserved
[    0.176660] system 00:03: [io  0x09f4-0x09ff] has been reserved
[    0.176669] system 00:03: [io  0x04d0-0x04d1] has been reserved
[    0.176678] system 00:03: [io  0x0900-0x09f3] has been reserved
[    0.176686] system 00:03: [io  0x0400-0x043f] has been reserved
[    0.176695] system 00:03: [io  0x0480-0x04bf] has been reserved
[    0.176705] system 00:03: [mem 0xf0000000-0xf0003fff] has been reserved
[    0.176714] system 00:03: [mem 0x00000384-0x00000387] could not be reserved
[    0.176726] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.177064] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.177490] system 00:05: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.177501] system 00:05: [mem 0xfee00000-0xfee00fff] has been reserved
[    0.177513] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.177780] pnp 00:06: Plug and Play ACPI device, IDs SYN0a13 SYN0a01 SYN0a04 SYN0002 PNP0f13 (active)
[    0.178049] system 00:07: [mem 0xe0000000-0xefffffff] has been reserved
[    0.178063] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.178778] system 00:08: [mem 0x00000000-0x0009ffff] could not be reserved
[    0.178789] system 00:08: [mem 0x000c0000-0x000cffff] could not be reserved
[    0.178798] system 00:08: [mem 0x000e0000-0x000fffff] could not be reserved
[    0.178807] system 00:08: [mem 0x00100000-0x7f7fffff] could not be reserved
[    0.178820] system 00:08: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.179428] pnp: PnP ACPI: found 9 devices
[    0.223746] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.223791] pci 0000:00:1c.0: bridge window [io  0x1000-0x0fff] to [bus 03] add_size 1000
[    0.223805] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff pref] to [bus 03] add_size 200000 add_align 100000
[    0.223815] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 03] add_size 200000 add_align 100000
[    0.223836] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] res_to_dev_res add_size 200000 min_align 100000
[    0.223845] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x002fffff] res_to_dev_res add_size 200000 min_align 100000
[    0.223854] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff pref] res_to_dev_res add_size 200000 min_align 100000
[    0.223864] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x002fffff pref] res_to_dev_res add_size 200000 min_align 100000
[    0.223873] pci 0000:00:1c.0: res[13]=[io  0x1000-0x0fff] res_to_dev_res add_size 1000 min_align 1000
[    0.223882] pci 0000:00:1c.0: res[13]=[io  0x1000-0x1fff] res_to_dev_res add_size 1000 min_align 1000
[    0.223899] pci 0000:00:1c.0: BAR 14: assigned [mem 0x80000000-0x801fffff]
[    0.223910] pci 0000:00:1c.0: BAR 15: assigned [mem 0x80200000-0x803fffff pref]
[    0.223922] pci 0000:00:1c.0: BAR 13: assigned [io  0x1000-0x1fff]
[    0.223933] pci 0000:00:1c.0: PCI bridge to [bus 03]
[    0.223942] pci 0000:00:1c.0:   bridge window [io  0x1000-0x1fff]
[    0.223955] pci 0000:00:1c.0:   bridge window [mem 0x80000000-0x801fffff]
[    0.223965] pci 0000:00:1c.0:   bridge window [mem 0x80200000-0x803fffff pref]
[    0.223979] pci 0000:00:1c.1: PCI bridge to [bus 01-02]
[    0.223987] pci 0000:00:1c.1:   bridge window [io  0xe000-0xefff]
[    0.223998] pci 0000:00:1c.1:   bridge window [mem 0xf4000000-0xfbffffff]
[    0.224029] pci 0000:00:1c.1:   bridge window [mem 0xcc000000-0xcfffffff pref]
[    0.224045] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.224053] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.224061] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.224069] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff window]
[    0.224077] pci_bus 0000:00: resource 8 [mem 0x7f800000-0xdfffffff window]
[    0.224085] pci_bus 0000:00: resource 9 [mem 0xf0000000-0xffffffff window]
[    0.224093] pci_bus 0000:03: resource 0 [io  0x1000-0x1fff]
[    0.224100] pci_bus 0000:03: resource 1 [mem 0x80000000-0x801fffff]
[    0.224108] pci_bus 0000:03: resource 2 [mem 0x80200000-0x803fffff pref]
[    0.224116] pci_bus 0000:01: resource 0 [io  0xe000-0xefff]
[    0.224124] pci_bus 0000:01: resource 1 [mem 0xf4000000-0xfbffffff]
[    0.224132] pci_bus 0000:01: resource 2 [mem 0xcc000000-0xcfffffff pref]
[    0.224227] NET: Registered protocol family 2
[    0.224774] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.224834] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.224905] TCP: Hash tables configured (established 8192 bind 8192)
[    0.224976] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.224998] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.225213] NET: Registered protocol family 1
[    0.225277] pci 0000:00:02.0: Video device with shadowed ROM
[    0.225447] PCI: CLS 32 bytes, default 64
[    0.225646] Unpacking initramfs...
[    0.444399] Freeing initrd memory: 4332K (f733f000 - f777a000)
[    0.444824] apm: BIOS not found.
[    0.445053] Scanning for low memory corruption every 60 seconds
[    0.446362] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.447231] Initialise system trusted keyring
[    0.447581] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    0.456250] zbud: loaded
[    0.456795] VFS: Disk quotas dquot_6.6.0
[    0.456979] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.457733] Key type big_key registered
[    0.458373] bounce: pool size: 64 pages
[    0.458565] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.458666] io scheduler noop registered
[    0.458677] io scheduler deadline registered
[    0.458843] io scheduler cfq registered (default)
[    0.459163] io scheduler bfq registered
[    0.459169] BFQ I/O-scheduler: v7r11
[    0.459687] pcieport 0000:00:1c.0: enabling device (0104 -> 0107)
[    0.460101] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.460138] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.460196] vesafb: mode is 1024x768x32, linelength=4096, pages=0
[    0.460202] vesafb: scrolling: redraw
[    0.460209] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    0.460259] vesafb: framebuffer at 0x7f800000, mapped to 0xf8400000, using 3072k, total 3072k
[    0.510271] Console: switching to colour frame buffer device 128x48
[    0.559656] fb0: VESA VGA frame buffer device
[    0.559756] intel_idle: MWAIT substates: 0x3020220
[    0.559777] intel_idle: v0.4 model 0x1C
[    0.559783] intel_idle: lapic_timer_reliable_states 0x2
[    0.559797] tsc: Marking TSC unstable due to TSC halts in idle states deeper than C2
[    0.560274] GHES: HEST is not enabled!
[    0.560347] isapnp: Scanning for PnP cards...
[    0.873668] isapnp: No Plug & Play device found
[    0.873863] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.875824] Failed to find cpu0 device node
[    0.876256] Unable to detect cache hierarchy from DT for CPU 0
[    0.876502] rtc_cmos 00:01: RTC can wake from S4
[    0.876833] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
[    0.876890] rtc_cmos 00:01: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    0.877075] ledtrig-cpu: registered to indicate activity on CPUs
[    0.878360] NET: Registered protocol family 10
[    0.879161] NET: Registered protocol family 17
[    0.879962] microcode: CPU0 sig=0x106c2, pf=0x1, revision=0x217
[    0.879994] microcode: CPU1 sig=0x106c2, pf=0x1, revision=0x217
[    0.880181] microcode: Microcode Update Driver: v2.01 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    0.880217] Using IPI No-Shortcut mode
[    0.880863] registered taskstats version 1
[    0.880895] Loading compiled-in X.509 certificates
[    0.880963] zswap: loaded using pool lzo/zbud
[    0.881638]   Magic number: 8:604:747
[    0.881786] rtc_cmos 00:01: setting system clock to 2016-03-27 18:44:57 UTC (1459104297)
[    0.882067] PM: Checking hibernation image partition UUID=a8300492-dceb-4a08-8e36-8df309a6b2ad
[    0.882079] PM: Hibernation image not present or could not be loaded.
[    0.882701] Freeing unused kernel memory: 612K (c16ca000 - c1763000)
[    0.882811] Write protecting the kernel text: 5016k
[    0.882907] Write protecting the kernel read-only data: 1412k
[    0.882914] BFS CPU scheduler v0.467 by Con Kolivas.
[    0.910645] random: systemd-tmpfile urandom read with 2 bits of entropy available
[    1.085153] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    1.114720] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.115132] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.147003] ACPI: bus type USB registered
[    1.147246] usbcore: registered new interface driver usbfs
[    1.147349] usbcore: registered new interface driver hub
[    1.147515] usbcore: registered new device driver usb
[    1.154714] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.156918] ehci-pci: EHCI PCI platform driver
[    1.156929] uhci_hcd: USB Universal Host Controller Interface driver
[    1.157353] ehci-pci 0000:00:1d.7: EHCI Host Controller
[    1.157385] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    1.157420] ehci-pci 0000:00:1d.7: debug port 1
[    1.161816] SCSI subsystem initialized
[    1.162081] ehci-pci 0000:00:1d.7: cache line size of 32 is not supported
[    1.162176] ehci-pci 0000:00:1d.7: irq 19, io mem 0xf3f37c00
[    1.168102] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    1.169449] hub 1-0:1.0: USB hub found
[    1.169523] hub 1-0:1.0: 8 ports detected
[    1.172403] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    1.172447] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    1.172477] uhci_hcd 0000:00:1d.0: detected 2 ports
[    1.172570] uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000c880
[    1.178669] hub 2-0:1.0: USB hub found
[    1.178726] hub 2-0:1.0: 2 ports detected
[    1.181746] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    1.181782] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    1.181808] uhci_hcd 0000:00:1d.1: detected 2 ports
[    1.181896] uhci_hcd 0000:00:1d.1: irq 21, io base 0x0000d080
[    1.182374] libata version 3.00 loaded.
[    1.183239] hub 3-0:1.0: USB hub found
[    1.183287] hub 3-0:1.0: 2 ports detected
[    1.184509] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    1.184554] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    1.184582] uhci_hcd 0000:00:1d.2: detected 2 ports
[    1.184677] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d480
[    1.185996] hub 4-0:1.0: USB hub found
[    1.186119] hub 4-0:1.0: 2 ports detected
[    1.187150] pata_sch 0000:00:1f.1: version 0.2
[    1.190882] scsi host0: pata_sch
[    1.191543] scsi host1: pata_sch
[    1.191968] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[    1.191982] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[    1.284318] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    1.353920] ata1.00: ATA-8: Hitachi HTS545025B9A300, PB2OC60N, max UDMA/133
[    1.353940] ata1.00: 488397168 sectors, multi 16: LBA48 
[    1.360981] ata1.00: configured for UDMA/100
[    1.372790] scsi 0:0:0:0: Direct-Access     ATA      Hitachi HTS54502 C60N PQ: 0 ANSI: 5
[    1.446357] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x13309fe02b0, max_idle_ns: 440795216996 ns
[    1.475283] usb 1-5: new high-speed USB device number 2 using ehci-pci
[    1.547215] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/233 GiB)
[    1.547463] sd 0:0:0:0: [sda] Write Protect is off
[    1.547480] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.547600] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.614817]  sda: sda1 sda2 < sda5 sda6 sda7 > sda3
[    1.617581] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.236782] random: nonblocking pool is initialized
[    2.705371] PM: Starting manual resume from disk
[    2.705385] PM: Hibernation image partition 8:5 present
[    2.705391] PM: Looking for hibernation image.
[    2.709879] PM: Image not found (code -22)
[    2.709898] PM: Hibernation image not present or could not be loaded.
[    3.079159] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    3.922523] systemd[1]: RTC configured in localtime, applying delta of 0 minutes to system time.
[    4.243046] ip_tables: (C) 2000-2006 Netfilter Core Team
[    4.330559] systemd[1]: systemd 229 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[    4.331128] systemd[1]: Detected architecture x86.
[    4.357550] systemd[1]: Set hostname to <archlinux-ASUS-netbook>.
[    6.113514] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[    6.114067] systemd[1]: Listening on udev Control Socket.
[    6.129374] systemd[1]: Listening on Process Core Dump Socket.
[    6.129622] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[    6.131281] systemd[1]: Created slice User and Session Slice.
[    6.131465] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[    6.132001] systemd[1]: Created slice System Slice.
[    6.132168] systemd[1]: Reached target Encrypted Volumes.
[    6.132378] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    6.132536] systemd[1]: Listening on LVM2 metadata daemon socket.
[    6.132749] systemd[1]: Listening on Journal Socket.
[    6.162628] systemd[1]: Mounting Temporary Directory...
[    6.166385] systemd[1]: Starting Remount Root and Kernel File Systems...
[    6.169603] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[    6.173647] systemd[1]: Mounting POSIX Message Queue File System...
[    6.179186] systemd[1]: Starting Setup Virtual Console...
[    6.182496] systemd[1]: Mounting Debug File System...
[    6.202569] systemd[1]: Starting Load Kernel Modules...
[    6.205441] systemd[1]: Mounting Huge Pages File System...
[    6.206514] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    6.236306] systemd[1]: Mounting NFSD configuration filesystem...
[    6.236615] systemd[1]: Listening on Journal Socket (/dev/log).
[    6.239894] systemd[1]: Starting Journal Service...
[    6.240079] systemd[1]: Reached target Slices.
[    6.240416] systemd[1]: Listening on udev Kernel Socket.
[    6.241708] systemd[1]: Created slice system-getty.slice.
[    6.249756] systemd[1]: Started Create list of required static device nodes for the current kernel.
[    6.444101] FS-Cache: Loaded
[    6.506815] RPC: Registered named UNIX socket transport module.
[    6.506827] RPC: Registered udp transport module.
[    6.506834] RPC: Registered tcp transport module.
[    6.506841] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    6.642454] FS-Cache: Netfs 'nfs' registered for caching
[    6.805125] systemd[1]: Started Setup Virtual Console.
[    6.822324] systemd[1]: Mounted POSIX Message Queue File System.
[    6.822537] systemd[1]: Mounted Debug File System.
[    6.827476] systemd[1]: Mounted Huge Pages File System.
[    6.836275] EXT4-fs (sda1): re-mounted. Opts: data=ordered
[    6.847950] systemd[1]: Started Remount Root and Kernel File Systems.
[    6.848783] systemd[1]: Mounted Temporary Directory.
[    6.889602] systemd[1]: Started Load Kernel Modules.
[    6.947684] systemd[1]: Starting Apply Kernel Variables...
[    6.953161] systemd[1]: Mounting Configuration File System...
[    6.984742] systemd[1]: Starting udev Coldplug all Devices...
[    6.989942] systemd[1]: Starting Create Static Device Nodes in /dev...
[    7.001711] systemd[1]: Starting Load/Save Random Seed...
[    7.246723] systemd[1]: Mounted Configuration File System.
[    7.388765] systemd[1]: Started Load/Save Random Seed.
[    7.516390] systemd[1]: Started udev Coldplug all Devices.
[    7.537207] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    7.542810] systemd[1]: Mounted NFSD configuration filesystem.
[    8.185217] systemd[1]: Started Create Static Device Nodes in /dev.
[    8.201688] systemd[1]: Starting udev Kernel Device Manager...
[    8.201943] systemd[1]: Reached target Local File Systems (Pre).
[    8.203462] systemd[1]: Reached target Local File Systems.
[    8.209005] systemd[1]: Starting Preprocess NFS configuration...
[    8.221112] systemd[1]: Started Apply Kernel Variables.
[    8.370710] systemd[1]: Starting CLI Netfilter Manager...
[    9.007329] systemd[1]: Started Journal Service.
[    9.263285] systemd-journald[148]: Received request to flush runtime journal from PID 1
[    9.656228] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[   10.047305] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   10.098661] ACPI: AC Adapter [AC0] (off-line)
[   10.439107] wmi: Mapper loaded
[   10.638401] eeepc_laptop: Eee PC Hotkey Driver
[   10.638624] eeepc_laptop: Hotkey init flags 0x41
[   10.640401] eeepc_laptop: TYPE (2000000) not reported by BIOS, enabling anyway
[   10.646479] eeepc_laptop: PANELPOWER (4000000) not reported by BIOS, enabling anyway
[   10.657084] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   10.663543] eeepc_laptop: TPD (8000000) not reported by BIOS, enabling anyway
[   10.663558] eeepc_laptop: Get control methods supported: 0xe901701
[   10.676780] FUJITSU Extended Socket Network Device Driver - version 1.0 - Copyright (c) 2015 FUJITSU LIMITED
[   10.681548] input: Asus EeePC extra buttons as /devices/platform/eeepc/input/input2
[   10.685748] ACPI: Battery Slot [BAT0] (battery present)
[   10.797875] thermal LNXTHERM:00: registered as thermal_zone0
[   10.797890] ACPI: Thermal Zone [TZ00] (52 C)
[   10.817597] Linux agpgart interface v0.103
[   10.820549] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input3
[   10.825810] ACPI: Lid Switch [LID]
[   10.826285] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input4
[   10.826308] ACPI: Sleep Button [SLPB]
[   10.826696] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input5
[   10.826714] ACPI: Power Button [PWRB]
[   11.127419] [drm] Initialized drm 1.1.0 20060810
[   11.303436] input: PC Speaker as /devices/platform/pcspkr/input/input7
[   11.763296] Intel(R) Wireless WiFi driver for Linux
[   11.763311] Copyright(c) 2003- 2015 Intel Corporation
[   11.819082] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-3160-17.ucode failed with error -2
[   12.001476] iwlwifi 0000:01:00.0: loaded firmware version 16.242414.0 op_mode iwlmvm
[   12.069430] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[   12.075980] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input8
[   12.076408] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[   12.076419] [drm] No driver support for vblank timestamp query.
[   12.360391] psmouse serio1: synaptics: queried max coordinates: x [..5624], y [..4754]
[   12.494960] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000/0x0, board id: 0, fw id: 600854
[   12.581245] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6
[   13.120823] media: Linux media interface: v0.10
[   13.373524] iwlwifi 0000:01:00.0: Detected Intel(R) Dual Band Wireless AC 3160, REV=0x164
[   13.373632] iwlwifi 0000:01:00.0: L1 Disabled - LTR Disabled
[   13.373870] iwlwifi 0000:01:00.0: RF_KILL bit toggled to disable radio.
[   13.373958] iwlwifi 0000:01:00.0: L1 Disabled - LTR Disabled
[   13.452754] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs'
[   13.760279] gma500 0000:00:02.0: trying to get vblank count for disabled pipe 0
[   13.761016] gma500 0000:00:02.0: trying to get vblank count for disabled pipe 0
[   13.764701] asus_wmi: unknown parameter 'blacklist' ignored
[   13.765776] asus_wmi: ASUS WMI generic driver loaded
[   13.827466] mousedev: PS/2 mouse device common for all mice
[   13.891715] Linux video capture interface: v2.00
[   13.938659] eeepc_wmi: Found legacy ATKD device (ASUS010)
[   13.938675] eeepc_wmi: WMI device present, but legacy ATKD device is also present and enabled
[   13.938682] eeepc_wmi: You probably booted with acpi_osi="Linux" or acpi_osi="!Windows 2009"
[   13.938689] eeepc_wmi: Can't load eeepc-wmi, use default acpi_osi (preferred) or eeepc-laptop
[   13.938713] eeepc-wmi: probe of eeepc-wmi failed with error -16
[   14.400230] checking generic (7f800000 300000) vs hw (7f800000 7bf000)
[   14.400246] fb: switching to psbdrmfb from VESA VGA
[   14.400356] Console: switching to colour dummy device 80x25
[   14.401129] fbcon: psbdrmfb (fb0) is primary device
[   14.481403] Console: switching to colour frame buffer device 170x48
[   14.579624] gma500 0000:00:02.0: fb0: psbdrmfb frame buffer device
[   14.584343] gma500 0000:00:02.0: Backlight lvds set brightness 7a127a12
[   14.584372] [drm] Initialized gma500 1.0.0 20140314 for 0000:00:02.0 on minor 0
[   14.684048] gma500 0000:00:02.0: Backlight lvds set brightness 7a127a12
[   14.734326] Adding 2440188k swap on /dev/sda5.  Priority:-1 extents:1 across:2440188k FS
[   14.745242] iwlwifi 0000:01:00.0: RF_KILL bit toggled to enable radio.
[   14.747891] gma500 0000:00:02.0: Backlight lvds set brightness 7a1219a2
[   15.128183] wl: module license 'Mixed/Proprietary' taints kernel.
[   15.128199] Disabling lock debugging due to kernel taint
[   15.272850] iwlwifi 0000:01:00.0 wlp1s0: renamed from wlan0
[   15.620217] uvcvideo: Found UVC 1.00 device USB2.0 UVC VGA WebCam (13d3:5111)
[   15.622687] input: USB2.0 UVC VGA WebCam as /devices/pci0000:00/0000:00:1d.7/usb1/1-5/1-5:1.0/input/input9
[   15.623163] usbcore: registered new interface driver uvcvideo
[   15.623173] USB Video Class driver (1.1.1)
[   16.337519] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
[   19.981735] gma500 0000:00:02.0: Backlight lvds set brightness 7a1219a2
[   20.994856] EXT4-fs (sda1): re-mounted. Opts: data=ordered,commit=600
[   21.559454] EXT4-fs (sda6): re-mounted. Opts: data=ordered,commit=600
[   23.132227] IPv6: ADDRCONF(NETDEV_UP): wlp1s0: link is not ready
[   23.132693] iwlwifi 0000:01:00.0: L1 Disabled - LTR Disabled
[   23.132933] iwlwifi 0000:01:00.0: L1 Disabled - LTR Disabled
[   23.238744] iwlwifi 0000:01:00.0: L1 Disabled - LTR Disabled
[   23.238981] iwlwifi 0000:01:00.0: L1 Disabled - LTR Disabled
[   23.255426] IPv6: ADDRCONF(NETDEV_UP): wlp1s0: link is not ready
[   23.658702] IPv6: ADDRCONF(NETDEV_UP): wlp1s0: link is not ready
[   28.053202] gma500 0000:00:02.0: Backlight lvds set brightness 7a1219a2
[   28.053212] gma500 0000:00:02.0: Backlight lvds set brightness 7a1219a2
[   30.736515] fuse init (API version 7.23)
[   38.222597] wlp1s0: authenticate with e0:1c:41:ac:32:14
[   38.226056] wlp1s0: send auth to e0:1c:41:ac:32:14 (try 1/3)
[   38.227530] wlp1s0: authenticated
[   38.235082] wlp1s0: associate with e0:1c:41:ac:32:14 (try 1/3)
[   38.236987] wlp1s0: RX AssocResp from e0:1c:41:ac:32:14 (capab=0x421 status=17 aid=0)
[   38.237041] wlp1s0: e0:1c:41:ac:32:14 denied association (code=17)
[   38.508505] wlp1s0: authenticate with e0:1c:41:ac:32:28
[   38.511450] wlp1s0: send auth to e0:1c:41:ac:32:28 (try 1/3)
[   38.512598] wlp1s0: authenticated
[   38.526068] wlp1s0: associate with e0:1c:41:ac:32:28 (try 1/3)
[   38.537844] wlp1s0: RX AssocResp from e0:1c:41:ac:32:28 (capab=0x401 status=0 aid=1)
[   38.540669] wlp1s0: associated
[   38.540714] IPv6: ADDRCONF(NETDEV_CHANGE): wlp1s0: link becomes ready
[   38.557881] wlp1s0: Limiting TX power to 20 (20 - 0) dBm as advertised by e0:1c:41:ac:32:28
[   40.059861] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
[   47.700836] [UFW BLOCK] IN=wlp1s0 OUT= MAC=01:00:5e:00:00:fb:1c:e6:2b:d0:f6:03:08:00 SRC=10.188.14.164 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=15714 PROTO=2
Xiaomi Notebook Pro i5/8 Gb - Archlinux/Plasma, kernel stock, Bumblebee (Nvidia)
Macbook Pro 8.2 - Archlinux/Plasma, kernel linux-macbook, Intel only.
HP Pavilion g6 1354ef - Archlinux/XFCE, kernel ck-sandybridge
Avatar de l’utilisateur
RoyalPanda
yeomen
Messages : 239
Inscription : lun. 19 mai 2014, 09:08

Re: [bluetooth] Asus EEEpc 1201HA (le retour!)

Message par RoyalPanda »

A priori, il y a deux versions d'EEEpc 1201HA et celle avec 1Go de RAM n'avait pas le bluetooth, ou en tout cas aucune mention n'en était faite.
Pour en revenir au bluetooth, de tête il faut activer le service bluetooth de systemd.
Sinon, les drivers semblent bon d'après le dmsg, en tout cas pour la carte Intel.
Avatar de l’utilisateur
benjarobin
Maître du Kyudo
Messages : 17235
Inscription : sam. 30 mai 2009, 15:48
Localisation : Lyon

Re: [bluetooth] Asus EEEpc 1201HA (le retour!)

Message par benjarobin »

Il ne manquerait pas le début de dmesg ? ce n'est pas trop grave on va compenser par ces questions :
Quelle est la sortie de

Code : Tout sélectionner

cat /proc/cmdline
grep -Evr "^ *$|^ *#" /etc/modprobe* /usr/lib/modprobe* /etc/modules-load* /usr/lib/modules-load* /etc/mkinitcpio.conf
Zsh | KDE | PC fixe : core i7, carte nvidia
Titre d'un sujet : [Thème] Sujet (état) / Règles du forum
Blabladodo
Hankyu
Messages : 37
Inscription : mer. 04 nov. 2015, 14:10
Localisation : Montpellier

Re: [bluetooth] Asus EEEpc 1201HA (le retour!)

Message par Blabladodo »

Bonsoir,

Merci pour ta réponse, non je ne pense pas qu'il manque le début de dmesg. Dans le doute voici le retour des commandes suivantes :

Code : Tout sélectionner

cat /proc/cmdline
BOOT_IMAGE=/boot/vmlinuz-linux-ck root=UUID=e9d5c28a-c0b5-49d0-bc3f-831afb6c53a2 rw mem=1920mb quiet resume=UUID=a8300492-dceb-4a08-8e36-8df309a6b2ad acpi_backlight=vendor acpi_osi=Linux

grep -Evr "^ *$|^ *#" /etc/modprobe* /usr/lib/modprobe* /etc/modules-load* /usr/lib/modules-load* /etc/mkinitcpio.conf
/usr/lib/modprobe.d/usb-load-ehci-first.conf:softdep ohci_hcd pre: ehci_hcd
/usr/lib/modprobe.d/usb-load-ehci-first.conf:softdep uhci_hcd pre: ehci_hcd
/usr/lib/modprobe.d/bluetooth-usb.conf:options btusb reset=1
/usr/lib/modules-load.d/nfs-utils.conf:nfs
/usr/lib/modules-load.d/thermald.conf:msr
/usr/lib/modules-load.d/thermald.conf:coretemp
/etc/mkinitcpio.conf:MODULES=""
/etc/mkinitcpio.conf:BINARIES=""
/etc/mkinitcpio.conf:FILES=""
/etc/mkinitcpio.conf:HOOKS="base udev autodetect modconf block resume filesystems keyboard fsck"
Merci par avance, cordialement.
Xiaomi Notebook Pro i5/8 Gb - Archlinux/Plasma, kernel stock, Bumblebee (Nvidia)
Macbook Pro 8.2 - Archlinux/Plasma, kernel linux-macbook, Intel only.
HP Pavilion g6 1354ef - Archlinux/XFCE, kernel ck-sandybridge
Avatar de l’utilisateur
waitnsea
Maître du Kyudo
Messages : 2114
Inscription : jeu. 15 mars 2012, 05:08

Re: [bluetooth] Asus EEEpc 1201HA (le retour!)

Message par waitnsea »

RoyalPanda a écrit :Pour en revenir au bluetooth, de tête il faut activer le service bluetooth de systemd.
bluetooth.service, effectivement
Blabladodo
Hankyu
Messages : 37
Inscription : mer. 04 nov. 2015, 14:10
Localisation : Montpellier

Re: [bluetooth] Asus EEEpc 1201HA (le retour!)

Message par Blabladodo »

Je n'ai pas pensé à la préciser plus haut, mais j'ai bel et bien déjà activé le service bluetooth (sudo systemctl enable bluetooth) ; aucun retour particulier lors de l'activation (ni au moment de son démarrage).
Xiaomi Notebook Pro i5/8 Gb - Archlinux/Plasma, kernel stock, Bumblebee (Nvidia)
Macbook Pro 8.2 - Archlinux/Plasma, kernel linux-macbook, Intel only.
HP Pavilion g6 1354ef - Archlinux/XFCE, kernel ck-sandybridge
Avatar de l’utilisateur
benjarobin
Maître du Kyudo
Messages : 17235
Inscription : sam. 30 mai 2009, 15:48
Localisation : Lyon

Re: [bluetooth] Asus EEEpc 1201HA (le retour!)

Message par benjarobin »

C'est quoi cette option asus_wmi.blacklist=yes, cela parrait très invalide ?
C'est vraiment nécessaire l'option mem=1920mb ?
As tu essayé sans acpi_backlight=vendor acpi_osi=Linux ?
Zsh | KDE | PC fixe : core i7, carte nvidia
Titre d'un sujet : [Thème] Sujet (état) / Règles du forum
Blabladodo
Hankyu
Messages : 37
Inscription : mer. 04 nov. 2015, 14:10
Localisation : Montpellier

Re: [bluetooth] Asus EEEpc 1201HA (le retour!)

Message par Blabladodo »

Alors pour te répondre :

-asus_wmi.blacklist=yes : ma table de luminosité étant un peu chaotique, blacklisté ce module semble aider (ce n'est toujours pas propre, mais lorsque je fais varier la luminosité avec les touches dédiées, je ne passe plus d'une luminosité nulle ou presque au maximum d'un coups, ça nivelle un peu on va dire)
-mem=1920mb : j'avais rajouté cette option suite à la lecteur de plusieurs posts au sujet des cartes Poulsbo et de leurs performances médiocres ... Il s'agit du réglages conseillé pour 2Go de RAM (ce qui est mon cas)
-je n'ai pas essayé sans les deux dernières options, je vais testé immédiatement, merci.


Edit : je viens de tester en désactivant toutes ces options (d'abord toutes en même temps, puis une par une, aucun changement hormis que le basculement de luminosité sur secteur/batterie ne se fait plus, mais ça avec les deux dernières options je m'y attendais).
Dernière modification par Blabladodo le mer. 30 mars 2016, 17:36, modifié 1 fois.
Xiaomi Notebook Pro i5/8 Gb - Archlinux/Plasma, kernel stock, Bumblebee (Nvidia)
Macbook Pro 8.2 - Archlinux/Plasma, kernel linux-macbook, Intel only.
HP Pavilion g6 1354ef - Archlinux/XFCE, kernel ck-sandybridge
Avatar de l’utilisateur
benjarobin
Maître du Kyudo
Messages : 17235
Inscription : sam. 30 mai 2009, 15:48
Localisation : Lyon

Re: [bluetooth] Asus EEEpc 1201HA (le retour!)

Message par benjarobin »

Tu n'as pas blacklister le module, tu lui passes un paramètre nommé blacklist est valant yes... D'aileurs dans les log le module essaye de se charger et se affiche un warning sur le paramètre inconnu blacklist
Pour blacklister tu as plusieurs solutions : https://wiki.archlinux.org/index.php/ke ... acklisting

Essayes donc sans tous ces paramètres au moins temporairement
Zsh | KDE | PC fixe : core i7, carte nvidia
Titre d'un sujet : [Thème] Sujet (état) / Règles du forum
Blabladodo
Hankyu
Messages : 37
Inscription : mer. 04 nov. 2015, 14:10
Localisation : Montpellier

Re: [bluetooth] Asus EEEpc 1201HA (le retour!)

Message par Blabladodo »

Edit : je viens de tester en désactivant toutes ces options (d'abord toutes en même temps, puis une par une, aucun changement hormis que le basculement de luminosité sur secteur/batterie ne se fait plus, mais ça avec les deux dernières options je m'y attendais).
Xiaomi Notebook Pro i5/8 Gb - Archlinux/Plasma, kernel stock, Bumblebee (Nvidia)
Macbook Pro 8.2 - Archlinux/Plasma, kernel linux-macbook, Intel only.
HP Pavilion g6 1354ef - Archlinux/XFCE, kernel ck-sandybridge
Avatar de l’utilisateur
benjarobin
Maître du Kyudo
Messages : 17235
Inscription : sam. 30 mai 2009, 15:48
Localisation : Lyon

Re: [bluetooth] Asus EEEpc 1201HA (le retour!)

Message par benjarobin »

Avec hcitool tu ne vois aucune interface bluetooth ?
Zsh | KDE | PC fixe : core i7, carte nvidia
Titre d'un sujet : [Thème] Sujet (état) / Règles du forum
Blabladodo
Hankyu
Messages : 37
Inscription : mer. 04 nov. 2015, 14:10
Localisation : Montpellier

Re: [bluetooth] Asus EEEpc 1201HA (le retour!)

Message par Blabladodo »

Aucune, ni avec rfkill list.

La carte pourrait-elle être mal gérée par le BIOS ?
Xiaomi Notebook Pro i5/8 Gb - Archlinux/Plasma, kernel stock, Bumblebee (Nvidia)
Macbook Pro 8.2 - Archlinux/Plasma, kernel linux-macbook, Intel only.
HP Pavilion g6 1354ef - Archlinux/XFCE, kernel ck-sandybridge
Avatar de l’utilisateur
benjarobin
Maître du Kyudo
Messages : 17235
Inscription : sam. 30 mai 2009, 15:48
Localisation : Lyon

Re: [bluetooth] Asus EEEpc 1201HA (le retour!)

Message par benjarobin »

Le BIOS ne devrait avoir aucune interaction avec ceci, vraiment je sèche... C'est comme s'il manquait un driver.
Je viens de réaliser que tu n'utilises pas le kernel des dépôts mais vmlinuz-linux-ck, il est fort probable qu'il n'y est pas tous les modules de compilé. Essaye avec le kernel officiel
Zsh | KDE | PC fixe : core i7, carte nvidia
Titre d'un sujet : [Thème] Sujet (état) / Règles du forum
Blabladodo
Hankyu
Messages : 37
Inscription : mer. 04 nov. 2015, 14:10
Localisation : Montpellier

Re: [bluetooth] Asus EEEpc 1201HA (le retour!)

Message par Blabladodo »

Aucun changement notable avec le kernel officiel.

Je vais tenter le livecd d'une autre distrib à tout hasard, faute de meilleure idée.
Xiaomi Notebook Pro i5/8 Gb - Archlinux/Plasma, kernel stock, Bumblebee (Nvidia)
Macbook Pro 8.2 - Archlinux/Plasma, kernel linux-macbook, Intel only.
HP Pavilion g6 1354ef - Archlinux/XFCE, kernel ck-sandybridge
Blabladodo
Hankyu
Messages : 37
Inscription : mer. 04 nov. 2015, 14:10
Localisation : Montpellier

Re: [bluetooth] Asus EEEpc 1201HA (le retour!)

Message par Blabladodo »

Rien de neuf avec un livecd ubuntu et un livecd manjaro.

Je vais réinstaller un Windows sur un quoi de mon disque dur, pour voir si au moins comme ça, j'arrive à avoir quelque chose ... ( :x )
Xiaomi Notebook Pro i5/8 Gb - Archlinux/Plasma, kernel stock, Bumblebee (Nvidia)
Macbook Pro 8.2 - Archlinux/Plasma, kernel linux-macbook, Intel only.
HP Pavilion g6 1354ef - Archlinux/XFCE, kernel ck-sandybridge
Blabladodo
Hankyu
Messages : 37
Inscription : mer. 04 nov. 2015, 14:10
Localisation : Montpellier

Re: [bluetooth] Asus EEEpc 1201HA (le retour!)

Message par Blabladodo »

Sous Windows même problème (je pense avoir installé tous les pilotes nécessaires pourtant) ; à part un problème matériel ou une mauvaise gestion au niveau du BIOS, je suis à court d'idées.
Xiaomi Notebook Pro i5/8 Gb - Archlinux/Plasma, kernel stock, Bumblebee (Nvidia)
Macbook Pro 8.2 - Archlinux/Plasma, kernel linux-macbook, Intel only.
HP Pavilion g6 1354ef - Archlinux/XFCE, kernel ck-sandybridge
Répondre