[CPU Fan] Le ventilateur est à 0 TPM (résolu)

Reconnaissance et configuration du matériel / kernel linux
Body
newbie
Messages : 8
Inscription : lun. 07 mars 2016, 23:26

[CPU Fan] Le ventilateur est à 0 TPM (résolu)

Message par Body »

Hello,

Je viens vers vous car j'ai un soucis avec le ventilateur de mon processeur. Un problème vraiment bizarre, je n'arrive pas à trouver la cause.

Je ne sais pas depuis combien de temps c'est comme ça mais je l'ai remarqué en compilant le kernel, mon PC s'est éteint à cause de la chaleur (+ de 100°).

J'ai un Dell Latitude 3340. J'avais commencé par regarder la configuration de sensord, je ne sais toujours pas comment ça fonctionne ce truc, de toute manière rien n'a changé... J'ai vu dans le forum anglais, qu'une personne proposait d'utiliser le module i8k mais pareil ça n'a rien changé et j'ai aussi regardé du côté de pwm.

Après la configuration, je m'étais dis que c'était sûrement hardware le problème mais maintenant je doute. Truc bizarre, en restant appuyer le bouton power pour forcer le PC à s'éteindre, pendant un court instant, le ventilateur se met à tourner... J'ai pas compris là. Du coup je démonte le PC et je vois rien d'anormal. Pas de poussière, rien. Quand je suis dans le BIOS, le ventilateur ne tourne pas non plus, du coup je me dis que c'est peut être pas mon arch qui déconne dû à une mauvaise conf.

Je décide donc de flash mon bios, j'avais la version A07 pour passer à la A12, grosse diff, je me dit peut être que ça peut jouer et là miracle au redémarrage du flash, il retourne même sur mon Arch ! Je suis content et tout, je me dis ça y ait j'ai réglé le problème mais là ce matin au démarrage du PC, ben il ne tourne plus... Ça me soule !

Du coup, si vous avez des pistes, je suis toute ouïe! (I need help, mon pc à chaud ! :) Thanks!
Dernière modification par Body le sam. 28 janv. 2017, 14:45, modifié 1 fois.
BlondVador
Chu Ko Nu
Messages : 302
Inscription : ven. 29 janv. 2010, 21:41

Re: [CPU Fan] Le ventilateur est à 0 TPM

Message par BlondVador »

Bonjour,

Il peut y avoir plusieurs raisons à cela. La première chose à faire est d'essayer de légèrement "aider" le ventilateur à tourner sur une machine en route. Pour cela, tu peux utiliser un objet long et fin (type aiguille, couteau...) et avec lequel tu pousseras délicatement le ventilo dans son sens rotatif afin de voir si ça le relance. Surtout ne pas forcer, au risque de désaxer le ventilo.

S'il ne se relance pas, il est probable qu'il soit défaillant et qu'il faille le changer. Si tu as du matériel, tu peux également tester le ventilo sur prise-secteur directement

Dans le doute, pourrais-tu nous montrer ta config sensord ?

Concernant le BIOS, il semblerait que la dernière version pour ton laptop soit la A10 d'après le constructeur et non A12 comme tu l'as écrit. Mais si ton laptop démarre toujours, je suppose que c'est juste une coquille qui s'est glissée là ;).
Body
newbie
Messages : 8
Inscription : lun. 07 mars 2016, 23:26

Re: [CPU Fan] Le ventilateur est à 0 TPM

Message par Body »

Merci pour ton retour :)

Ça marche, je vais essayer ça chez moi ce soir et je te tiens au courant.

Yep, la voici:

Code : Tout sélectionner

# libsensors configuration file
# -----------------------------
#
# This default configuration file only includes statements which do not
# differ from one mainboard to the next. Only label, compute and set
# statements for internal voltage and temperature sensors are included.
#
# In general, local changes should not be added to this file, but rather
# placed in custom configuration files located in /etc/sensors.d. This
# approach makes further updates much easier.
#
# Such custom configuration files for specific mainboards can be found at
# http://www.lm-sensors.org/wiki/Configurations

chip "lm78-*" "lm79-*" "lm80-*" "lm96080-*"

    label temp1 "M/B Temp"


chip "w83792d-*"

    label in0 "VcoreA"
    label in1 "VcoreB"
    label in6 "+5V"
    label in7 "5VSB"
    label in8 "Vbat"

    set in6_min  5.0 * 0.90
    set in6_max  5.0 * 1.10
    set in7_min  5.0 * 0.90
    set in7_max  5.0 * 1.10
    set in8_min  3.0 * 0.90
    set in8_max  3.0 * 1.10


chip "w83793-*"

    label in0 "VcoreA"
    label in1 "VcoreB"
    label in7 "+5V"
    label in8 "5VSB"
    label in9 "Vbat"

    set in7_min  5.0 * 0.90
    set in7_max  5.0 * 1.10
    set in8_min  5.0 * 0.90
    set in8_max  5.0 * 1.10
    set in9_min  3.0 * 0.90
    set in9_max  3.0 * 1.10


chip "w83795g-*" "w83795adg-*"

    label in12 "+3.3V"
    label in13 "3VSB"
    label in14 "Vbat"

    set in12_min  3.3 * 0.90
    set in12_max  3.3 * 1.10
    set in13_min  3.3 * 0.90
    set in13_max  3.3 * 1.10
    set in14_min  3.0 * 0.90
    set in14_max  3.3 * 1.10


chip "via686a-*"

    label in0 "Vcore"
    label in2 "+3.3V"
    label in3 "+5V"
    label in4 "+12V"

    set in2_min  3.3 * 0.90
    set in2_max  3.3 * 1.10
    set in3_min  5.0 * 0.90
    set in3_max  5.0 * 1.10
    set in4_min 12.0 * 0.90
    set in4_max 12.0 * 1.10


chip "adm1025-*" "ne1619-*"

    label in1 "Vcore"
    label in2 "+3.3V"
    label in3 "+5V"
    label in4 "+12V"
    label in5 "VCC"

    set in2_min  3.3 * 0.90
    set in2_max  3.3 * 1.10
    set in3_min  5.0 * 0.90
    set in3_max  5.0 * 1.10
    set in5_min  3.3 * 0.90
    set in5_max  3.3 * 1.10
# Depending on how your chip is hardwired, you may or may not have
# +12V readings.
#    set in4_min 12.0 * 0.90
#    set in4_max 12.0 * 1.10

    label temp1 "CPU Temp"
    label temp2 "M/B Temp"


chip "lm87-*" "adm1024-*"

    label in1 "Vcore"
    label in2 "+3.3V"
    label in3 "+5V"
    label in4 "+12V"

    set in2_min  3.3 * 0.90
    set in2_max  3.3 * 1.10
    set in3_min  5.0 * 0.90
    set in3_max  5.0 * 1.10
    set in4_min 12.0 * 0.90
    set in4_max 12.0 * 1.10

    label temp1 "M/B Temp"
    label temp2 "CPU Temp"


chip "it87-*" "it8712-*" "it8716-*" "it8718-*" "it8720-*"

    label in8 "Vbat"


chip "fscpos-*" "fscher-*"
#FSC "Hermes"

    label in0 "+12V"
    label in1 "+5V"
    label in2 "Vbat"

    label temp1 "CPU Temp"
    label temp2 "M/B Temp"
    label temp3 "Aux Temp"


chip "fscscy-*"
#FSC "Scylla"

    label in0 "+12V"
    label in1 "+5V"
    label in2 "+3.3V"

    label temp1 "CPU0 Temp"
    label temp2 "CPU1 Temp"
    label temp3 "M/B Temp"
    label temp4 "Aux Temp"


chip "fschds-*"
# Fujitsu Technology Solutions, "Hades"-Chip

# Temperatures
    label temp1 "CPU Temp"
    label temp2 "Super I/O Temp"
    label temp3 "System Temp"

# Fans
    label fan1 "PSU Fan"
    label fan2 "CPU Fan"
    label fan3 "System FAN2"
    label fan4 "System FAN3"
    label fan5 "System FAN4"

# Voltages
    label in0 "+12V"
    label in1 "+5V"
    label in2 "Vbat"

chip "fscsyl-*"
# Fujitsu Technology Solutions, "Syleus"-Chip

# Temperatures
    label temp1 "CPU Temp"
    label temp4 "Super I/O Temp"
    label temp5 "Northbridge Temp"

# Fans
    label fan1 "CPU Fan"
    label fan2 "System FAN2"
    label fan3 "System FAN3"
    label fan4 "System FAN4"
    label fan7 "PSU Fan"

# Voltages
    label in0 "+12V"
    label in1 "+5V"
    label in2 "Vbat"
    label in3 "+3.3V"
    label in5 "+3.3V-Aux"

chip "vt1211-*"

    label in5 "+3.3V"

    label temp2 "SIO Temp"


chip "vt8231-*"

    label in5 "+3.3V"


chip "smsc47m192-*"

    label in1 "Vcore"
    label in2 "+3.3V"
    label in3 "+5V"
    label in4 "+12V"
    label in5 "VCC"

    set in2_min  3.3 * 0.90
    set in2_max  3.3 * 1.10
    set in3_min  5.0 * 0.90
    set in3_max  5.0 * 1.10
    set in4_min 12.0 * 0.90
    set in4_max 12.0 * 1.10
    set in5_min  3.3 * 0.90
    set in5_max  3.3 * 1.10

    label temp1 "SIO Temp"


chip "lm85-*" "lm85b-*" "lm85c-*" "adm1027-*" "adt7463-*" "adt7468-*" \
     "emc6d100-*" "emc6d102-*" "emc6d103-*" "emc6d103s-*" 

    label in1 "Vcore"
    label in2 "+3.3V"
    label in3 "+5V"
    label in4 "+12V"

    set in2_min  3.3 * 0.90
    set in2_max  3.3 * 1.10
    set in3_min  5.0 * 0.90
    set in3_max  5.0 * 1.10
# Depending on how your chip is hardwired, you may or may not have
# +12V readings.
#    set in4_min 12.0 * 0.90
#    set in4_max 12.0 * 1.10

    label temp2 "M/B Temp"


chip "emc6w201-*"

    label in2 "+3.3V"
    label in3 "+5V"

    label temp6 "M/B Temp"


chip "pc87365-*" "pc87366-*"

# Voltage inputs

    label in7 "3VSB"
    label in8 "VDD"
    label in9 "Vbat"
    label in10 "AVDD"

    compute in7   @*2, @/2
    compute in8   @*2, @/2
    compute in10  @*2, @/2

# These are the operating conditions as recommended by National
# Semiconductor
    set in7_min   3.0
    set in7_max   3.6
    set in8_min   3.0
    set in8_max   3.6
    set in10_min  3.0
    set in10_max  3.6
# Depending on the hardware setup, the battery voltage may or may not
# be monitored.
#    set in9_min   2.4
#    set in9_max   3.6

    label temp3 "SIO Temp"

    set temp3_min    0
    set temp3_max   70
    set temp3_crit  85


chip "adm1030-*" "adm1031-*"

    label temp1 "M/B Temp"


chip "w83627thf-*"

    label in3 "+5V"
    label in7 "5VSB"
    label in8 "Vbat"

    # Internal resistors
    compute in3  @ * (1 + 34/51), @ / (1 + 34/51)
    compute in7  @ * (1 + 34/51), @ / (1 + 34/51)

    set in3_min  5.0 * 0.90
    set in3_max  5.0 * 1.10
    set in7_min  5.0 * 0.90
    set in7_max  5.0 * 1.10
# The battery voltage may or may not be monitored.
#    set in8_min  3.0 * 0.90
#    set in8_max  3.0 * 1.10


chip "w83627ehf-*" "w83627dhg-*" "w83667hg-*" "nct6775-*" "nct6776-*" "nct6779-*" "nct6791-*"

    label in0 "Vcore"
    label in2 "AVCC"
    label in3 "+3.3V"
    label in7 "3VSB"
    label in8 "Vbat"

    set in2_min  3.3 * 0.90
    set in2_max  3.3 * 1.10
    set in3_min  3.3 * 0.90
    set in3_max  3.3 * 1.10
    set in7_min  3.3 * 0.90
    set in7_max  3.3 * 1.10
    set in8_min  3.0 * 0.90
    set in8_max  3.3 * 1.10


chip "w83627uhg-*"

    label in2 "AVCC"
    label in3 "+5V"
    label in7 "5VSB"
    label in8 "Vbat"

    set in2_min  5.0 * 0.90
    set in2_max  5.0 * 1.10
    set in3_min  5.0 * 0.90
    set in3_max  5.0 * 1.10
    set in7_min  5.0 * 0.90
    set in7_max  5.0 * 1.10
    set in8_min  3.0 * 0.90
    set in8_max  3.3 * 1.10


chip "f71805f-*"

    label in0 "+3.3V"

    set in0_min  3.3 * 0.90
    set in0_max  3.3 * 1.10


chip "f71872f-*"

    label in0 "+3.3V"
    label in9 "Vbat"
    label in10 "3VSB"

    set in0_min   3.3 * 0.90
    set in0_max   3.3 * 1.10
    set in9_min   3.0 * 0.90
    set in9_max   3.0 * 1.10
    set in10_min  3.3 * 0.90
    set in10_max  3.3 * 1.10


chip "k8temp-*"

    label temp1 "Core0 Temp"
    label temp2 "Core0 Temp"
    label temp3 "Core1 Temp"
    label temp4 "Core1 Temp"


chip "dme1737-*"

    label in0 "5VSB"
    label in1 "Vcore"
    label in2 "+3.3V"
    label in3 "+5V"
    label in4 "+12V"
    label in5 "3VSB"
    label in6 "Vbat"

    label temp2 "SIO Temp"

    set in0_min  5.0 * 0.90
    set in0_max  5.0 * 1.10
    set in2_min  3.3 * 0.90
    set in2_max  3.3 * 1.10
    set in3_min  5.0 * 0.90
    set in3_max  5.0 * 1.10
    set in4_min 12.0 * 0.90
    set in4_max 12.0 * 1.10
    set in5_min  3.3 * 0.90
    set in5_max  3.3 * 1.10
    set in6_min  3.0 * 0.90
    set in6_max  3.0 * 1.10


chip "sch311x-*"

    label in1 "Vcore"
    label in2 "+3.3V"
    label in3 "+5V"
    label in4 "+12V"
    label in5 "3VSB"
    label in6 "Vbat"

    label temp2 "SIO Temp"

    set in2_min  3.3 * 0.90
    set in2_max  3.3 * 1.10
    set in3_min  5.0 * 0.90
    set in3_max  5.0 * 1.10
    set in4_min 12.0 * 0.90
    set in4_max 12.0 * 1.10
    set in5_min  3.3 * 0.90
    set in5_max  3.3 * 1.10
    set in6_min  3.0 * 0.90
    set in6_max  3.0 * 1.10


chip "sch5027-*"

    label in0 "5VSB"
    label in1 "Vcore"
    label in2 "+3.3V"
    label in5 "3VSB"
    label in6 "Vbat"

    label temp2 "SIO Temp"

    set in0_min  5.0 * 0.90
    set in0_max  5.0 * 1.10
    set in2_min  3.3 * 0.90
    set in2_max  3.3 * 1.10
    set in5_min  3.3 * 0.90
    set in5_max  3.3 * 1.10
    set in6_min  3.0 * 0.90
    set in6_max  3.0 * 1.10


chip "sch5127-*"

    label in2 "+3.3V"
    label in5 "3VSB"
    label in6 "Vbat"

    set in2_min  3.3 * 0.90
    set in2_max  3.3 * 1.10
    set in5_min  3.3 * 0.90
    set in5_max  3.3 * 1.10
    set in6_min  3.0 * 0.90
    set in6_max  3.0 * 1.10


chip "f71808e-*" "f71808a-*" "f71862fg-*" "f71869-*" "f71869a-*" "f71882fg-*" \
     "f71889fg-*" "f71889ed-*" "f71889a-*"

    label in0 "+3.3V"
    label in7 "3VSB"
    label in8 "Vbat"

    compute in0  @*2, @/2
    compute in7  @*2, @/2
    compute in8  @*2, @/2


chip "f71858fg-*" "f8000-*"

    label in0 "+3.3V"
    label in1 "3VSB"
    label in2 "Vbat"

    compute in0  @*2, @/2
    compute in1  @*2, @/2
    compute in2  @*2, @/2


chip "f81865f-*"

    label in0 "+3.3V"
    label in5 "3VSB"
    label in6 "Vbat"

    compute in0  @*2, @/2
    compute in5  @*2, @/2
    compute in6  @*2, @/2


chip "adt7473-*" "adt7475-*"

    label in2 "+3.3V"

    set in2_min  3.3 * 0.90
    set in2_max  3.3 * 1.10

    label temp2 "Board Temp"


chip "adt7476-*" "adt7490-*"

    label in1 "Vcore"
    label in2 "+3.3V"
    label in3 "+5V"
    label in4 "+12V"

    set in2_min  3.3 * 0.90
    set in2_max  3.3 * 1.10
    set in3_min  5.0 * 0.90
    set in3_max  5.0 * 1.10
# Depending on how your ADT7476 is hardwired, you may or may not have
# +12V readings.
#    set in4_min 12.0 * 0.90
#    set in4_max 12.0 * 1.10

    label temp2 "M/B Temp"
La conf a été générée par sensors-detect, j'avais commencé par la faire à la main au début après j'ai vu qu'il y avait la commande ^^

Ben pour le BIOS, j'ai saisi mon serial number dans le support et ça m'a proposé cette version.
Body
newbie
Messages : 8
Inscription : lun. 07 mars 2016, 23:26

Re: [CPU Fan] Le ventilateur est à 0 TPM

Message par Body »

Bon finalement, je me suis aperçu que ma configuration dans /etc/fancontrol n'était pas bonne. J'ai utilisé la commande 'pwmconfig' pour tester les paramètres et en lisant la doc, je suis arrivé à une conf à peu près normal du coup le ventilateur démarre à partir une certaine température. En dessous de 20° il ne tourne plus sinon il tourne constamment et de plus en plus vite en fonction de la température.

ICC encore une fois :P
Répondre