sous ubuntu & debian etch, j'utilise sans problèmes wicd pour gérer mon reseau wifi, crypté en WPA2
nouveau sous archlinux, j'ai bien installé le nécessaire, mais wicd ne détecte aucun réseau wifi
lsmod me montre bien
Code : Tout sélectionner
rt2500pci 19840 0
rt2x00pci 7552 1 rt2500pci
rt2x00lib 16000 2 rt2500pci,rt2x00pci
et chargement du module rt2500pci
iwconfig :
Code : Tout sélectionner
lo no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11g ESSID:""
Mode:Managed Channel:0 Access Point: Not-Associated
Retry min limit:7 RTS thr:off Fragment thr=2346 B
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
eth0 no wireless extensions.
Code : Tout sélectionner
eth0 Link encap:Ethernet HWaddr 00:11:2F:AB:E6:AC
inet addr:10.0.0.10 Bcast:10.0.0.255 Mask:255.255.255.0
inet6 addr: fe80::211:2fff:feab:e6ac/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2231 errors:0 dropped:0 overruns:0 frame:0
TX packets:2292 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:576422 (562.9 Kb) TX bytes:245734 (239.9 Kb)
Interrupt:17
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:5 errors:0 dropped:0 overruns:0 frame:0
TX packets:5 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:309 (309.0 b) TX bytes:309 (309.0 b)
wlan0 Link encap:Ethernet HWaddr 00:08:A1:85:C6:7B
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
wmaster0 Link encap:UNSPEC HWaddr 00-08-A1-85-C6-7B-00-00-00-00-00-00-00-00-00-00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Code : Tout sélectionner
iwlist wlan0 scanning
wlan0 No scan results
j'ai toujours trouvé la gestion du wifi compliquée, sauf depuis l'apparition de ce merveilleux outils qu'est wicd, qui est compatible avec mon matériel et le WPA2
sauf avec arch pour l'instant
mais je me doute que ce n'est que temporaire