J'ai un disque dur qui présente ce genre d'anomalies :
Code : Tout sélectionner
# smartctl -a /dev/sdb
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.15.5-1-ARCH] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Blue (SATA)
Device Model: WDC WD3200AAKS-75SBA0
Serial Number: WD-WCAPZ1352448
LU WWN Device Id: 5 0014ee 1557ed784
Firmware Version: 12.01B01
User Capacity: 320 072 933 376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 (minor revision not indicated)
Local Time is: Sat Mar 3 10:01:31 2018 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 8400) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 106) minutes.
Conveyance self-test routine
recommended polling time: ( 6) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 157 152 021 Pre-fail Always - 5141
4 Start_Stop_Count 0x0032 097 097 000 Old_age Always - 3178
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000e 200 200 051 Old_age Always - 0
9 Power_On_Hours 0x0032 080 080 000 Old_age Always - 14741
10 Spin_Retry_Count 0x0012 100 100 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0012 100 100 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 097 097 000 Old_age Always - 3127
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 8
193 Load_Cycle_Count 0x0032 199 199 000 Old_age Always - 3178
194 Temperature_Celsius 0x0022 113 091 000 Old_age Always - 34
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 051 Old_age Offline - 0
SMART Error Log Version: 1
ATA Error Count: 895 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 895 occurred at disk power-on lifetime: 8307 hours (346 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 90 61 65 40 Error: UNC at LBA = 0x00656190 = 6644112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 80 08 7f 61 65 00 00 02:00:33.688 READ FPDMA QUEUED
60 80 08 ff 60 65 00 00 02:00:33.687 READ FPDMA QUEUED
60 80 08 7f 60 65 00 00 02:00:33.687 READ FPDMA QUEUED
60 80 08 ff 5f 65 00 00 02:00:33.686 READ FPDMA QUEUED
60 80 08 7f 5f 65 00 00 02:00:33.685 READ FPDMA QUEUED
Error 894 occurred at disk power-on lifetime: 8293 hours (345 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 90 61 65 40 Error: UNC at LBA = 0x00656190 = 6644112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 80 08 7f 61 65 00 00 04:55:53.752 READ FPDMA QUEUED
60 80 08 ff 60 65 00 00 04:55:53.751 READ FPDMA QUEUED
60 80 08 7f 60 65 00 00 04:55:53.751 READ FPDMA QUEUED
60 80 08 ff 5f 65 00 00 04:55:53.750 READ FPDMA QUEUED
60 80 08 7f 5f 65 00 00 04:55:53.749 READ FPDMA QUEUED
Error 893 occurred at disk power-on lifetime: 8293 hours (345 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 90 61 65 40 Error: UNC at LBA = 0x00656190 = 6644112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 80 08 7f 61 65 00 00 04:55:11.004 READ FPDMA QUEUED
60 80 08 ff 60 65 00 00 04:55:11.003 READ FPDMA QUEUED
60 80 08 7f 60 65 00 00 04:55:11.002 READ FPDMA QUEUED
60 80 08 ff 5f 65 00 00 04:55:11.001 READ FPDMA QUEUED
60 80 08 7f 5f 65 00 00 04:55:11.000 READ FPDMA QUEUED
Error 892 occurred at disk power-on lifetime: 8260 hours (344 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 90 61 65 40 Error: UNC at LBA = 0x00656190 = 6644112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 20 08 87 61 65 00 00 00:39:03.612 READ FPDMA QUEUED
60 08 08 7f 61 65 00 00 00:39:03.598 READ FPDMA QUEUED
61 08 08 97 5f 67 00 00 00:39:03.570 WRITE FPDMA QUEUED
61 10 08 7f 5a 67 00 00 00:39:03.569 WRITE FPDMA QUEUED
61 08 08 6f 5a 67 00 00 00:39:03.568 WRITE FPDMA QUEUED
Error 891 occurred at disk power-on lifetime: 8260 hours (344 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 90 61 65 40 Error: UNC at LBA = 0x00656190 = 6644112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 80 08 7f 61 65 00 00 00:38:39.192 READ FPDMA QUEUED
60 80 08 ff 60 65 00 00 00:38:39.192 READ FPDMA QUEUED
60 80 08 7f 60 65 00 00 00:38:39.191 READ FPDMA QUEUED
60 80 08 ff 5f 65 00 00 00:38:39.190 READ FPDMA QUEUED
60 80 08 7f 5f 65 00 00 00:38:39.190 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 14739 -
# 2 Conveyance offline Completed without error 00% 14738 -
# 3 Short offline Completed without error 00% 14738 -
# 4 Conveyance offline Completed without error 00% 14602 -
# 5 Extended offline Completed without error 00% 14602 -
# 6 Short offline Completed without error 00% 14600 -
# 7 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Code : Tout sélectionner
# pvdisplay && vgdisplay && lvdisplay
--- Physical volume ---
PV Name /dev/sda5
VG Name VG_Data
PV Size <296,59 GiB / not usable 3,00 MiB
Allocatable yes (but full)
PE Size 4,00 MiB
Total PE 75926
Free PE 0
Allocated PE 75926
PV UUID TrZEr1-0qOv-d3WA-ke2b-qOUD-r39A-yQsX18
--- Physical volume ---
PV Name /dev/sdb5
VG Name VG_Data
PV Size <296,59 GiB / not usable 3,00 MiB
Allocatable yes
PE Size 4,00 MiB
Total PE 75926
Free PE 31532
Allocated PE 44394
PV UUID QEtwU1-xq6p-6KBK-Ou4M-kMac-obLf-qi33BT
--- Volume group ---
VG Name VG_Data
System ID
Format lvm2
Metadata Areas 2
Metadata Sequence No 5
VG Access read/write
VG Status resizable
MAX LV 0
Cur LV 3
Open LV 3
Max PV 0
Cur PV 2
Act PV 2
VG Size 593,17 GiB
PE Size 4,00 MiB
Total PE 151852
Alloc PE / Size 120320 / 470,00 GiB
Free PE / Size 31532 / 123,17 GiB
VG UUID l1cVR9-dZO9-I0jr-LgXn-wr12-r9cP-hCstdX
--- Logical volume ---
LV Path /dev/VG_Data/LV_VBox
LV Name LV_VBox
VG Name VG_Data
LV UUID Xnk6pf-36Wv-mEmW-g4Qb-wRQj-se59-IqjcfT
LV Write Access read/write
LV Creation host, time PC_Master, 2018-02-11 11:46:18 +0100
LV Status available
# open 1
LV Size 300,00 GiB
Current LE 76800
Segments 2
Allocation inherit
Read ahead sectors auto
- currently set to 256
Block device 254:0
--- Logical volume ---
LV Path /dev/VG_Data/LV_Repository
LV Name LV_Repository
VG Name VG_Data
LV UUID TDTuNc-fgGr-pTtc-cPnu-GkT6-ersf-cQAfxC
LV Write Access read/write
LV Creation host, time PC_Master, 2018-02-11 11:47:08 +0100
LV Status available
# open 1
LV Size 30,00 GiB
Current LE 7680
Segments 1
Allocation inherit
Read ahead sectors auto
- currently set to 256
Block device 254:1
--- Logical volume ---
LV Path /dev/VG_Data/LV_Shared
LV Name LV_Shared
VG Name VG_Data
LV UUID YyLQ0i-ymYw-lSdk-cIHb-YmAW-uTVw-r7G0du
LV Write Access read/write
LV Creation host, time PC_Master, 2018-02-11 11:50:19 +0100
LV Status available
# open 1
LV Size 140,00 GiB
Current LE 35840
Segments 1
Allocation inherit
Read ahead sectors auto
- currently set to 256
Block device 254:2
Comment puis-je procéder ?
- Sauvegarde des données, remplacement du disque et récréation des pv, vg et lv ?
- ou existe t'il un autre moyen ?
Merci d'avance pour votre aide.