Archlinux.fr [Forums]

Code : Tout sélectionner

grep "^HOOKS=" etc/mkinitcpio.conf

Code : Tout sélectionner

# 
# /etc/fstab: static file system information
#
# <file system>	<dir>	<type>	<options>	<dump>	<pass>
tmpfs		/tmp	tmpfs	nodev,nosuid	0	0
# UUID=7a6fe60f-3fd1-453d-b706-40a3cc9d47fd
/dev/sda2           	/         	ext4      	rw,relatime,data=ordered	0 1

# UUID=9d1cabd8-0b84-45f9-97bc-c253fd727732
/dev/sda1           	/boot     	ext4      	rw,relatime,data=ordered	0 2

# UUID=07588396-cf70-4ef9-ba78-96733a7b46f4
/dev/sda5           	/usr      	ext4      	rw,relatime,data=ordered	0 2

# UUID=5ec5733a-a240-43a8-8812-bae8e37a688f
/dev/sda6           	/var      	ext4      	rw,relatime,data=ordered	0 2

# UUID=ede82b5e-3c36-453d-903f-9b6145c4eba4
/dev/sda7           	/tmp      	ext4      	rw,relatime,data=ordered	0 2

# UUID=49b4c399-28fe-4600-8d2e-0c0a7cd01c1b
/dev/sda8           	/home     	ext4      	rw,relatime,data=ordered	0 2

Code : Tout sélectionner

# vim:set ft=sh
# MODULES
# The following modules are loaded before any boot hooks are
# run.  Advanced users may wish to specify all system modules
# in this array.  For instance:
#     MODULES="piix ide_disk reiserfs"
MODULES=""

# BINARIES
# This setting includes any additional binaries a given user may
# wish into the CPIO image.  This is run last, so it may be used to
# override the actual binaries included by a given hook
# BINARIES are dependency parsed, so you may safely ignore libraries
BINARIES=""

# FILES
# This setting is similar to BINARIES above, however, files are added
# as-is and are not parsed in any way.  This is useful for config files.
# Some users may wish to include modprobe.conf for custom module options
# like so:
#    FILES="/etc/modprobe.d/modprobe.conf"
FILES=""

# HOOKS
# This is the most important setting in this file.  The HOOKS control the
# modules and scripts added to the image, and what happens at boot time.
# Order is important, and it is recommended that you do not change the
# order in which HOOKS are added.  Run 'mkinitcpio -H <hook name>' for
# help on a given hook.
# 'base' is _required_ unless you know precisely what you are doing.
# 'udev' is _required_ in order to automatically load modules
# 'filesystems' is _required_ unless you specify your fs modules in MODULES
# Examples:
##   This setup specifies all modules in the MODULES setting above.
##   No raid, lvm2, or encrypted root is needed.
#    HOOKS="base"
#
##   This setup will autodetect all modules for your system and should
##   work as a sane default
#    HOOKS="base udev autodetect pata scsi sata filesystems"
#
##   This is identical to the above, except the old ide subsystem is
##   used for IDE devices instead of the new pata subsystem.
#    HOOKS="base udev autodetect ide scsi sata filesystems"
#
##   This setup will generate a 'full' image which supports most systems.
##   No autodetection is done.
#    HOOKS="base udev pata scsi sata usb filesystems"
#
##   This setup assembles a pata mdadm array with an encrypted root FS.
##   Note: See 'mkinitcpio -H mdadm' for more information on raid devices.
#    HOOKS="base udev pata mdadm encrypt filesystems"
#
##   This setup loads an lvm2 volume group on a usb device.
#    HOOKS="base udev usb lvm2 filesystems"
#
##   NOTE: If you have /usr on a separate partition, you MUST include the
#    usr, fsck and shutdown hooks.
HOOKS="base udev autodetect pata scsi sata filesystems usbinput fsck"

# COMPRESSION
# Use this to compress the initramfs image. By default, gzip compression
# is used. Use 'cat' to create an uncompressed image.
#COMPRESSION="gzip"
#COMPRESSION="bzip2"
#COMPRESSION="lzma"
#COMPRESSION="xz"
#COMPRESSION="lzop"

# COMPRESSION_OPTIONS
# Additional options for the compressor
#COMPRESSION_OPTIONS=""

Code : Tout sélectionner

HOOKS="base udev autodetect pata scsi sata filesystems usbinput fsck shutdown usr"

Code : Tout sélectionner

mkinitcpio -p linux