Archlinux.fr [Forums]

Forum d'entraide ! Posez vos questions ici
https://forums.archlinux.fr/

[Catalyst] Serveur X plante

https://forums.archlinux.fr/viewtopic.php?t=15027

Page 1 sur 1

[Catalyst] Serveur X plante

Publié : mer. 26 févr. 2014, 22:56
par fate
Bonjour,

Il y a une semaine de ça je me suis refait un pc avec, entre autre, une R9 270X (modéle MSI Radeon R9 270X GAMING) et depuis j'essaye vainement de faire marche cette sal***rie de carte avec les drivers proprio catalyst sous linux. Le problème est le suivant : dés que je lance une appli qui demande de la 3d (un benchmark ou un jeu) j'ai le serveur X qui plante dans la minute. Le système tourne toujours, par exemple si je lance un mp3 en même temps que le benchmark, après avoir lancé le benchmark le X plante (écran figé) mais la musique tourne toujours. Par contre impossible d'accéder à quoi que ce soit, même avec CTRL+ALT+F1.
Je tourne donc sous archlinux 64 bit kde avec les pilotes proprio installé via AUR. J'ai la version test des pilotes vu que mon xorg est trop récent pour pouvoir installer la version stable.
Depuis une semaine j'ai eu le temps de faire pas mal de test. A la base j'étais sous debian sid 64 bits kde. Que ce soit avec le paquet fglrx beta ou en installant les pilotes avec le .run fourni par AMD j'avais exactement le même problème. Je suis donc passé en version stable (wheezy) pour installer le paquet fglrx stable mais le problème était toujours présent (idem pour le .run en version stable fourni par AMD). Ne trouvant strictement rien sur les forum debian/ubuntu ainsi que dans mes logs (à part un message de segmentation fault dans les logs de xorg, ce qui m'avance pas beaucoup) j'ai pensé tout bêtement à un problème matériel de ma carte. J'ai donc installé Windows seven avec le pilote catalyst et là aucun souci. J'ai lancé le benchmark valley d'Unigine (le même que j'avais lancé sous debian) ainsi que Guid Wars 2 et aucun souci, rien qui plante.
En désespoir de cause je tente de changer de distro et je prend donc Archlinux. Après quelques difficultés pour arriver à installer la dite distro, j'arrive à avoir une joli interface kde et j'installe les pilotes proprio via AUR mais encore et toujours le X qui plante dès que la carte est sollicité. Là j'en arrive à un point où, si j'avais les moyens de m'assoir sur 180€ cette foutu carte aurait déjà fait un vol plané de 4 étages...

Niveau config voici mon fichier xorg.conf (généré par la commande aticonfig --initial auquel j'ai rajouté la section DRI comme indiqué dans le wiki) :

Code : Tout sélectionner

Section "ServerLayout"
	Identifier     "aticonfig Layout"
	Screen      0  "aticonfig-Screen[0]-0" 0 0
EndSection

Section "Module"
EndSection

Section "Monitor"
	Identifier   "aticonfig-Monitor[0]-0"
	Option	    "VendorName" "ATI Proprietary Driver"
	Option	    "ModelName" "Generic Autodetecting Monitor"
	Option	    "DPMS" "true"
EndSection

Section "Monitor"
	Identifier   "0-DFP5"
	Option	    "VendorName" "ATI Proprietary Driver"
	Option	    "ModelName" "Generic Autodetecting Monitor"
	Option	    "DPMS" "true"
	Option	    "Disable" "true"
EndSection

Section "Monitor"
	Identifier   "0-CRT1"
	Option	    "VendorName" "ATI Proprietary Driver"
	Option	    "ModelName" "Generic Autodetecting Monitor"
	Option	    "DPMS" "true"
	Option	    "PreferredMode" "1440x900"
	Option	    "TargetRefresh" "60"
	Option	    "Position" "0 0"
	Option	    "Rotate" "normal"
	Option	    "Disable" "false"
EndSection

Section "Device"
	Identifier  "aticonfig-Device[0]-0"
	Driver      "fglrx"
	Option	    "Monitor-DFP5" "0-DFP5"
	Option	    "Monitor-CRT1" "0-CRT1"
	BusID       "PCI:1:0:0"
EndSection

Section "Screen"
	Identifier "aticonfig-Screen[0]-0"
	Device     "aticonfig-Device[0]-0"
	DefaultDepth     24
	SubSection "Display"
		Viewport   0 0
		Depth     24
	EndSubSection
EndSection

Section "DRI"
     Mode 0666
EndSection
et voici le log de xorg de la session ou il a planté

Le log de xorg

Code : Tout sélectionner

[     9.662] 
X.Org X Server 1.15.0
Release Date: 2013-12-27
[     9.662] X Protocol Version 11, Revision 0
[     9.662] Build Operating System: Linux 3.12.5-1-ARCH x86_64 
[     9.662] Current Operating System: Linux debian 3.13.5-1-ARCH #1 SMP PREEMPT Sun Feb 23 00:25:24 CET 2014 x86_64
[     9.662] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=8362a543-b963-4f4c-93ca-462e09ba331c rw quiet nomodeset
[     9.662] Build Date: 09 January 2014  08:47:24AM
[     9.662]  
[     9.662] Current version of pixman: 0.32.4
[     9.662] 	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
[     9.662] Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[     9.662] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Feb 26 20:59:51 2014
[     9.690] (==) Using config file: "/etc/X11/xorg.conf"
[     9.690] (==) Using config directory: "/etc/X11/xorg.conf.d"
[     9.723] (==) ServerLayout "aticonfig Layout"
[     9.723] (**) |-->Screen "aticonfig-Screen[0]-0" (0)
[     9.723] (**) |   |-->Monitor "<default monitor>"
[     9.724] (**) |   |-->Device "aticonfig-Device[0]-0"
[     9.724] (==) No monitor specified for screen "aticonfig-Screen[0]-0".
	Using a default monitor configuration.
[     9.724] (==) Automatically adding devices
[     9.724] (==) Automatically enabling devices
[     9.724] (==) Automatically adding GPU devices
[     9.770] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[     9.770] 	Entry deleted from font path.
[     9.776] (==) FontPath set to:
	/usr/share/fonts/misc/,
	/usr/share/fonts/TTF/,
	/usr/share/fonts/OTF/,
	/usr/share/fonts/100dpi/,
	/usr/share/fonts/75dpi/
[     9.776] (==) ModulePath set to "/usr/lib/xorg/modules"
[     9.776] (II) The server relies on udev to provide the list of input devices.
	If no devices become available, reconfigure udev or disable AutoAddDevices.
[     9.776] (II) Loader magic: 0x804c80
[     9.776] (II) Module ABI versions:
[     9.776] 	X.Org ANSI C Emulation: 0.4
[     9.776] 	X.Org Video Driver: 15.0
[     9.776] 	X.Org XInput driver : 20.0
[     9.776] 	X.Org Server Extension : 8.0
[     9.777] (--) PCI:*(0:1:0:0) 1002:6810:1462:3030 rev 0, Mem @ 0xe0000000/268435456, 0xf7e00000/262144, I/O @ 0x0000e000/256, BIOS @ 0x????????/131072
[     9.777] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[     9.798] Initializing built-in extension Generic Event Extension
[     9.798] Initializing built-in extension SHAPE
[     9.798] Initializing built-in extension MIT-SHM
[     9.798] Initializing built-in extension XInputExtension
[     9.798] Initializing built-in extension XTEST
[     9.798] Initializing built-in extension BIG-REQUESTS
[     9.798] Initializing built-in extension SYNC
[     9.798] Initializing built-in extension XKEYBOARD
[     9.798] Initializing built-in extension XC-MISC
[     9.798] Initializing built-in extension SECURITY
[     9.798] Initializing built-in extension XINERAMA
[     9.798] Initializing built-in extension XFIXES
[     9.798] Initializing built-in extension RENDER
[     9.798] Initializing built-in extension RANDR
[     9.798] Initializing built-in extension COMPOSITE
[     9.798] Initializing built-in extension DAMAGE
[     9.798] Initializing built-in extension MIT-SCREEN-SAVER
[     9.798] Initializing built-in extension DOUBLE-BUFFER
[     9.798] Initializing built-in extension RECORD
[     9.798] Initializing built-in extension DPMS
[     9.798] Initializing built-in extension Present
[     9.798] Initializing built-in extension DRI3
[     9.798] Initializing built-in extension X-Resource
[     9.798] Initializing built-in extension XVideo
[     9.798] Initializing built-in extension XVideo-MotionCompensation
[     9.798] Initializing built-in extension XFree86-VidModeExtension
[     9.798] Initializing built-in extension XFree86-DGA
[     9.798] Initializing built-in extension XFree86-DRI
[     9.798] Initializing built-in extension DRI2
[     9.798] (II) "glx" will be loaded by default.
[     9.798] (II) LoadModule: "glx"
[     9.829] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[     9.849] (II) Module glx: vendor="Advanced Micro Devices, Inc."
[     9.849] 	compiled for 6.9.0, module version = 1.0.0
[     9.849] Loading extension GLX
[     9.849] (II) LoadModule: "fglrx"
[     9.850] (II) Loading /usr/lib/xorg/modules/drivers/fglrx_drv.so
[    10.016] (II) Module fglrx: vendor="FireGL - AMD Technologies Inc."
[    10.016] 	compiled for 1.4.99.906, module version = 13.35.5
[    10.016] 	Module class: X.Org Video Driver
[    10.017] (II) Loading sub module "fglrxdrm"
[    10.017] (II) LoadModule: "fglrxdrm"
[    10.017] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
[    10.038] (II) Module fglrxdrm: vendor="FireGL - AMD Technologies Inc."
[    10.038] 	compiled for 1.4.99.906, module version = 13.35.5
[    10.038] (II) AMD Proprietary Linux Driver Version Identifier:13.35.5
[    10.038] (II) AMD Proprietary Linux Driver Release Identifier: UNSUPPORTED-13.35.1005               
[    10.038] (II) AMD Proprietary Linux Driver Build Date: Jan 29 2014 21:41:24
[    10.038] (++) using VT number 7

[    10.143] (WW) Falling back to old probe method for fglrx
[    10.207] (II) Loading PCS database from /etc/ati/amdpcsdb /etc/ati/amdpcsdb.default
[    10.208] ukiDynamicMajor: found major device number 250
[    10.208] ukiDynamicMajor: found major device number 250
[    10.208] ukiOpenByBusid: Searching for BusID PCI:1:0:0
[    10.208] ukiOpenDevice: node name is /dev/ati/card0
[    10.208] ukiOpenDevice: open result is 9, (OK)
[    10.500] ukiOpenByBusid: ukiOpenMinor returns 9
[    10.501] ukiOpenByBusid: ukiGetBusid reports PCI:1:0:0
[    10.566] (--) Chipset Supported AMD Graphics Processor (0x6810) found
[    10.566] (WW) fglrx: No matching Device section for instance (BusID PCI:0@1:0:1) found
[    10.567] (II) fglrx(0): pEnt->device->identifier=0x26bdf40
[    10.567] (II) fglrx(0): === [xdl_xs115_atiddxPreInit] === begin
[    10.567] (II) Loading sub module "vgahw"
[    10.567] (II) LoadModule: "vgahw"
[    10.567] (II) Loading /usr/lib/xorg/modules/libvgahw.so
[    10.582] (II) Module vgahw: vendor="X.Org Foundation"
[    10.582] 	compiled for 1.15.0, module version = 0.1.0
[    10.582] 	ABI class: X.Org Video Driver, version 15.0
[    10.582] (**) fglrx(0): Depth 24, (--) framebuffer bpp 32
[    10.582] (II) fglrx(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
[    10.582] (==) fglrx(0): Default visual is TrueColor
[    10.582] (==) fglrx(0): RGB weight 888
[    10.582] (II) fglrx(0): Using 8 bits per RGB 
[    10.582] (==) fglrx(0): Buffer Tiling is ON
[    10.582] (II) Loading sub module "fglrxdrm"
[    10.582] (II) LoadModule: "fglrxdrm"
[    10.582] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
[    10.582] (II) Module fglrxdrm: vendor="FireGL - AMD Technologies Inc."
[    10.582] 	compiled for 1.4.99.906, module version = 13.35.5
[    10.583] ukiDynamicMajor: found major device number 250
[    10.583] ukiDynamicMajor: found major device number 250
[    10.583] ukiOpenByBusid: Searching for BusID PCI:1:0:0
[    10.583] ukiOpenDevice: node name is /dev/ati/card0
[    10.583] ukiOpenDevice: open result is 11, (OK)
[    10.583] ukiOpenByBusid: ukiOpenMinor returns 11
[    10.583] ukiOpenByBusid: ukiGetBusid reports PCI:1:0:0
[    10.583] (**) fglrx(0): NoAccel = NO
[    10.583] (**) fglrx(0): AMD 2D Acceleration Architecture enabled
[    10.583] (--) fglrx(0): Chipset: "AMD Radeon R9 200 Series" (Chipset = 0x6810)
[    10.583] (--) fglrx(0): (PciSubVendor = 0x1462, PciSubDevice = 0x3030)
[    10.583] (==) fglrx(0): board vendor info: third party graphics adapter - NOT original AMD
[    10.583] (--) fglrx(0): Linear framebuffer (phys) at 0xe0000000
[    10.583] (--) fglrx(0): MMIO registers at 0xf7e00000
[    10.583] (--) fglrx(0): I/O port at 0x0000e000
[    10.583] (==) fglrx(0): ROM-BIOS at 0x000c0000
[    10.594] (II) fglrx(0): AC Adapter is used
[    10.601] (II) fglrx(0): Primary V_BIOS segment is: 0xc000
[    10.602] (II) Loading sub module "vbe"
[    10.602] (II) LoadModule: "vbe"
[    10.602] (II) Loading /usr/lib/xorg/modules/libvbe.so
[    10.603] (II) Module vbe: vendor="X.Org Foundation"
[    10.603] 	compiled for 1.15.0, module version = 1.1.0
[    10.603] 	ABI class: X.Org Video Driver, version 15.0
[    10.603] (II) fglrx(0): VESA BIOS detected
[    10.603] (II) fglrx(0): VESA VBE Version 3.0
[    10.603] (II) fglrx(0): VESA VBE Total Mem: 16384 kB
[    10.604] (II) fglrx(0): VESA VBE OEM: AMD ATOMBIOS
[    10.604] (II) fglrx(0): VESA VBE OEM Software Rev: 15.41
[    10.604] (II) fglrx(0): VESA VBE OEM Vendor: (C) 1988-2010, Advanced Micro Devices, Inc.
[    10.604] (II) fglrx(0): VESA VBE OEM Product: CURACAO
[    10.604] (II) fglrx(0): VESA VBE OEM Product Rev: 01.00
[    10.604] (II) fglrx(0): AMD Video BIOS revision 9 or later detected
[    10.604] (--) fglrx(0): Video RAM: 2097152 kByte, Type: GDDR5
[    10.604] (II) fglrx(0): PCIE card detected
[    10.604] (--) fglrx(0): Using per-process page tables (PPPT) as GART.
[    10.604] (WW) fglrx(0): board is an unknown third party board, chipset is supported
[    10.604] (II) fglrx(0): [FB] MC range(MCFBBase = 0xf400000000, MCFBSize = 0x80000000)
[    10.604] (II) fglrx(0): RandR 1.2 support is enabled!
[    10.604] (II) fglrx(0): RandR 1.2 rotation support is enabled!
[    10.604] (II) Loading sub module "fb"
[    10.604] (II) LoadModule: "fb"
[    10.604] (II) Loading /usr/lib/xorg/modules/libfb.so
[    10.605] (II) Module fb: vendor="X.Org Foundation"
[    10.605] 	compiled for 1.15.0, module version = 1.0.0
[    10.605] 	ABI class: X.Org ANSI C Emulation, version 0.4
[    10.605] (II) fglrx(0): EDID Management option: EDID Management is enabled
[    10.605] (II) Loading sub module "ddc"
[    10.605] (II) LoadModule: "ddc"
[    10.605] (II) Module "ddc" already built-in
[    10.825] (II) fglrx(0): Output DFP1 has no monitor section
[    10.825] (II) fglrx(0): Output DFP2 has no monitor section
[    10.825] (II) fglrx(0): Output DFP3 has no monitor section
[    10.825] (II) fglrx(0): Output DFP4 has no monitor section
[    10.825] (II) fglrx(0): Output DFP5 using monitor section 0-DFP5
[    10.825] (**) fglrx(0): Option "Disable" "true"
[    10.825] (II) fglrx(0): Output DFP6 has no monitor section
[    10.825] (II) fglrx(0): Output DFP7 has no monitor section
[    10.825] (II) fglrx(0): Output CRT1 using monitor section 0-CRT1
[    10.825] (**) fglrx(0): Option "PreferredMode" "1440x900"
[    10.825] (**) fglrx(0): Option "Position" "0 0"
[    10.825] (**) fglrx(0): Option "Disable" "false"
[    10.825] (**) fglrx(0): Option "Rotate" "normal"
[    10.825] (**) fglrx(0): Option "TargetRefresh" "60"
[    10.825] (II) Loading sub module "ddc"
[    10.825] (II) LoadModule: "ddc"
[    10.825] (II) Module "ddc" already built-in
[    10.825] (II) fglrx(0): Connected Display0: DFP5
[    10.825] (II) fglrx(0): Display0 EDID data ---------------------------
[    10.825] (II) fglrx(0): Manufacturer: PHL  Model: 0  Serial#: 16843009
[    10.825] (II) fglrx(0): Year: 2010  Week: 3
[    10.825] (II) fglrx(0): EDID Version: 1.3
[    10.825] (II) fglrx(0): Digital Display Input
[    10.825] (II) fglrx(0): Max Image Size [cm]: horiz.: 128  vert.: 72
[    10.825] (II) fglrx(0): Gamma: 2.20
[    10.825] (II) fglrx(0): No DPMS capabilities specified
[    10.825] (II) fglrx(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 
[    10.825] (II) fglrx(0): First detailed timing is preferred mode
[    10.825] (II) fglrx(0): redX: 0.640 redY: 0.330   greenX: 0.290 greenY: 0.600
[    10.825] (II) fglrx(0): blueX: 0.150 blueY: 0.060   whiteX: 0.289 whiteY: 0.299
[    10.825] (II) fglrx(0): Supported established timings:
[    10.825] (II) fglrx(0): 640x480@60Hz
[    10.825] (II) fglrx(0): 800x600@60Hz
[    10.825] (II) fglrx(0): 1024x768@60Hz
[    10.825] (II) fglrx(0): Manufacturer's mask: 0
[    10.825] (II) fglrx(0): Supported standard timings:
[    10.825] (II) fglrx(0): #0: hsize: 1360  vsize 765  refresh: 60  vid: 49291
[    10.825] (II) fglrx(0): #1: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
[    10.825] (II) fglrx(0): #2: hsize: 1600  vsize 1200  refresh: 60  vid: 16553
[    10.825] (II) fglrx(0): Supported detailed timing:
[    10.825] (II) fglrx(0): clock: 148.5 MHz   Image Size:  1280 x 720 mm
[    10.825] (II) fglrx(0): h_active: 1920  h_sync: 2008  h_sync_end 2052 h_blank_end 2200 h_border: 0
[    10.825] (II) fglrx(0): v_active: 1080  v_sync: 1084  v_sync_end 1089 v_blanking: 1125 v_border: 0
[    10.825] (II) fglrx(0): Supported detailed timing:
[    10.825] (II) fglrx(0): clock: 148.5 MHz   Image Size:  1280 x 720 mm
[    10.825] (II) fglrx(0): h_active: 1920  h_sync: 2448  h_sync_end 2492 h_blank_end 2640 h_border: 0
[    10.825] (II) fglrx(0): v_active: 1080  v_sync: 1084  v_sync_end 1089 v_blanking: 1125 v_border: 0
[    10.825] (II) fglrx(0): Monitor name: Philips FTV
[    10.825] (II) fglrx(0): Ranges: V min: 48 V max: 62 Hz, H min: 15 H max: 70 kHz, PixClock max 175 MHz
[    10.825] (II) fglrx(0): Supported detailed timing:
[    10.825] (II) fglrx(0): clock: 74.2 MHz   Image Size:  1280 x 720 mm
[    10.825] (II) fglrx(0): h_active: 1920  h_sync: 2558  h_sync_end 2602 h_blank_end 2750 h_border: 0
[    10.825] (II) fglrx(0): v_active: 1080  v_sync: 1084  v_sync_end 1089 v_blanking: 1125 v_border: 0
[    10.825] (II) fglrx(0): Supported detailed timing:
[    10.825] (II) fglrx(0): clock: 74.2 MHz   Image Size:  1280 x 720 mm
[    10.825] (II) fglrx(0): h_active: 1920  h_sync: 2448  h_sync_end 2492 h_blank_end 2640 h_border: 0
[    10.825] (II) fglrx(0): v_active: 540  v_sync: 542  v_sync_end 547 v_blanking: 562 v_border: 0
[    10.825] (II) fglrx(0): Supported detailed timing:
[    10.825] (II) fglrx(0): clock: 74.2 MHz   Image Size:  1280 x 720 mm
[    10.825] (II) fglrx(0): h_active: 1280  h_sync: 1720  h_sync_end 1760 h_blank_end 1980 h_border: 0
[    10.825] (II) fglrx(0): v_active: 720  v_sync: 725  v_sync_end 730 v_blanking: 750 v_border: 0
[    10.825] (II) fglrx(0): Supported detailed timing:
[    10.825] (II) fglrx(0): clock: 74.2 MHz   Image Size:  1280 x 720 mm
[    10.825] (II) fglrx(0): h_active: 1920  h_sync: 2008  h_sync_end 2052 h_blank_end 2200 h_border: 0
[    10.825] (II) fglrx(0): v_active: 540  v_sync: 542  v_sync_end 547 v_blanking: 562 v_border: 0
[    10.825] (II) fglrx(0): Number of EDID sections to follow: 1
[    10.825] (II) fglrx(0): EDID (in hex):
[    10.825] (II) fglrx(0): 	00ffffffffffff00410c000001010101
[    10.825] (II) fglrx(0): 	03140103808048780ae692a3544a9926
[    10.825] (II) fglrx(0): 	0f4a4c2108008bc08180a94001010101
[    10.825] (II) fglrx(0): 	010101010101023a801871382d40582c
[    10.825] (II) fglrx(0): 	450000d05200001e023a80d072382d40
[    10.825] (II) fglrx(0): 	102c458000d05200001e000000fc0050
[    10.825] (II) fglrx(0): 	68696c697073204654560a20000000fd
[    10.825] (II) fglrx(0): 	00303e0f4611000a20202020202001c9
[    10.825] (II) fglrx(0): End of Display0 EDID data --------------------
[    10.825] (II) fglrx(0): Connected Display1: CRT1
[    10.825] (II) fglrx(0): Display1 EDID data ---------------------------
[    10.825] (II) fglrx(0): Manufacturer: HSD  Model: 1c2b  Serial#: 933
[    10.825] (II) fglrx(0): Year: 2008  Week: 17
[    10.825] (II) fglrx(0): EDID Version: 1.3
[    10.825] (II) fglrx(0): Analog Display Input,  Input Voltage Level: 0.700/0.300 V
[    10.825] (II) fglrx(0): Sync:  Separate  SyncOnGreen
[    10.825] (II) fglrx(0): Max Image Size [cm]: horiz.: 41  vert.: 26
[    10.825] (II) fglrx(0): Gamma: 2.20
[    10.825] (II) fglrx(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display
[    10.825] (II) fglrx(0): First detailed timing is preferred mode
[    10.825] (II) fglrx(0): redX: 0.643 redY: 0.325   greenX: 0.295 greenY: 0.616
[    10.825] (II) fglrx(0): blueX: 0.143 blueY: 0.081   whiteX: 0.310 whiteY: 0.330
[    10.825] (II) fglrx(0): Supported established timings:
[    10.825] (II) fglrx(0): 720x400@70Hz
///
///
/// (suppression pour pas dépasser la limite de caractère max)
[    10.825] (II) fglrx(0): Manufacturer's mask: 0
[    10.825] (II) fglrx(0): Supported standard timings:
[    10.825] (II) fglrx(0): #0: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
[    10.825] (II) fglrx(0): #1: hsize: 1280  vsize 720  refresh: 60  vid: 49281
[    10.825] (II) fglrx(0): #2: hsize: 1280  vsize 960  refresh: 60  vid: 16513
[    10.825] (II) fglrx(0): #3: hsize: 1152  vsize 864  refresh: 75  vid: 20337
[    10.825] (II) fglrx(0): #4: hsize: 1024  vsize 768  refresh: 66  vid: 18017
[    10.825] (II) fglrx(0): #5: hsize: 1400  vsize 1050  refresh: 75  vid: 20368
[    10.825] (II) fglrx(0): #6: hsize: 1440  vsize 900  refresh: 75  vid: 3989
[    10.825] (II) fglrx(0): Supported detailed timing:
[    10.825] (II) fglrx(0): clock: 106.5 MHz   Image Size:  408 x 255 mm
[    10.825] (II) fglrx(0): h_active: 1440  h_sync: 1520  h_sync_end 1672 h_blank_end 1904 h_border: 0
[    10.825] (II) fglrx(0): v_active: 900  v_sync: 903  v_sync_end 909 v_blanking: 934 v_border: 0
[    10.825] (II) fglrx(0): Ranges: V min: 55 V max: 75 Hz, H min: 30 H max: 83 kHz, PixClock max 145 MHz
[    10.825] (II) fglrx(0): Serial No: 817PA3BY00933
[    10.825] (II) fglrx(0): Monitor name: Hanns.G HG191
[    10.825] (II) fglrx(0): EDID (in hex):
[    10.825] (II) fglrx(0): 	00ffffffffffff0022642b1ca5030000
[    10.825] (II) fglrx(0): 	111201030a291a78ea9bb6a4534b9d24
[    10.825] (II) fglrx(0): 	144f54bfef80818081c08140714f6146
[    10.825] (II) fglrx(0): 	904f950f01019a29a0d0518422305098
[    10.825] (II) fglrx(0): 	360098ff1000001e000000fd00374b1e
[    10.825] (II) fglrx(0): 	530e000a202020202020000000ff0038
[    10.825] (II) fglrx(0): 	313750413342593030393333000000fc
[    10.825] (II) fglrx(0): 	0048616e6e732e4720484731393100de
[    10.825] (II) fglrx(0): End of Display1 EDID data --------------------
[    10.825] (II) fglrx(0): Dynamic Surface Resizing Enabled
[    10.826] (II) fglrx(0): EDID for output DFP1
[    10.826] (II) fglrx(0): EDID for output DFP2
[    10.826] (II) fglrx(0): EDID for output DFP3
[    10.826] (II) fglrx(0): EDID for output DFP4
[    10.826] (II) fglrx(0): EDID for output DFP5
[    10.826] (II) fglrx(0): Manufacturer: PHL  Model: 0  Serial#: 16843009
[    10.826] (II) fglrx(0): Year: 2010  Week: 3
[    10.826] (II) fglrx(0): EDID Version: 1.3
[    10.826] (II) fglrx(0): Digital Display Input
[    10.826] (II) fglrx(0): Max Image Size [cm]: horiz.: 128  vert.: 72
[    10.826] (II) fglrx(0): Gamma: 2.20
[    10.826] (II) fglrx(0): No DPMS capabilities specified
[    10.826] (II) fglrx(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 
[    10.826] (II) fglrx(0): First detailed timing is preferred mode
[    10.826] (II) fglrx(0): redX: 0.640 redY: 0.330   greenX: 0.290 greenY: 0.600
[    10.826] (II) fglrx(0): blueX: 0.150 blueY: 0.060   whiteX: 0.289 whiteY: 0.299
[    10.826] (II) fglrx(0): Supported established timings:
[    10.826] (II) fglrx(0): 640x480@60Hz
[    10.826] (II) fglrx(0): 800x600@60Hz
[    10.826] (II) fglrx(0): 1024x768@60Hz
[    10.826] (II) fglrx(0): Manufacturer's mask: 0
[    10.826] (II) fglrx(0): Supported standard timings:
[    10.826] (II) fglrx(0): #0: hsize: 1360  vsize 765  refresh: 60  vid: 49291
[    10.826] (II) fglrx(0): #1: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
[    10.826] (II) fglrx(0): #2: hsize: 1600  vsize 1200  refresh: 60  vid: 16553
[    10.826] (II) fglrx(0): Supported detailed timing:
[    10.826] (II) fglrx(0): clock: 148.5 MHz   Image Size:  1280 x 720 mm
[    10.826] (II) fglrx(0): h_active: 1920  h_sync: 2008  h_sync_end 2052 h_blank_end 2200 h_border: 0
[    10.826] (II) fglrx(0): v_active: 1080  v_sync: 1084  v_sync_end 1089 v_blanking: 1125 v_border: 0
[    10.826] (II) fglrx(0): Supported detailed timing:
[    10.826] (II) fglrx(0): clock: 148.5 MHz   Image Size:  1280 x 720 mm
[    10.826] (II) fglrx(0): h_active: 1920  h_sync: 2448  h_sync_end 2492 h_blank_end 2640 h_border: 0
[    10.826] (II) fglrx(0): v_active: 1080  v_sync: 1084  v_sync_end 1089 v_blanking: 1125 v_border: 0
[    10.826] (II) fglrx(0): Monitor name: Philips FTV
[    10.826] (II) fglrx(0): Ranges: V min: 48 V max: 62 Hz, H min: 15 H max: 70 kHz, PixClock max 175 MHz
[    10.826] (II) fglrx(0): Supported detailed timing:
[    10.826] (II) fglrx(0): clock: 74.2 MHz   Image Size:  1280 x 720 mm
[    10.826] (II) fglrx(0): h_active: 1920  h_sync: 2558  h_sync_end 2602 h_blank_end 2750 h_border: 0
[    10.826] (II) fglrx(0): v_active: 1080  v_sync: 1084  v_sync_end 1089 v_blanking: 1125 v_border: 0
[    10.826] (II) fglrx(0): Supported detailed timing:
[    10.826] (II) fglrx(0): clock: 74.2 MHz   Image Size:  1280 x 720 mm
[    10.826] (II) fglrx(0): h_active: 1920  h_sync: 2448  h_sync_end 2492 h_blank_end 2640 h_border: 0
[    10.826] (II) fglrx(0): v_active: 540  v_sync: 542  v_sync_end 547 v_blanking: 562 v_border: 0
[    10.826] (II) fglrx(0): Supported detailed timing:
[    10.826] (II) fglrx(0): clock: 74.2 MHz   Image Size:  1280 x 720 mm
[    10.826] (II) fglrx(0): h_active: 1280  h_sync: 1720  h_sync_end 1760 h_blank_end 1980 h_border: 0
[    10.826] (II) fglrx(0): v_active: 720  v_sync: 725  v_sync_end 730 v_blanking: 750 v_border: 0
[    10.826] (II) fglrx(0): Supported detailed timing:
[    10.826] (II) fglrx(0): clock: 74.2 MHz   Image Size:  1280 x 720 mm
[    10.826] (II) fglrx(0): h_active: 1920  h_sync: 2008  h_sync_end 2052 h_blank_end 2200 h_border: 0
[    10.826] (II) fglrx(0): v_active: 540  v_sync: 542  v_sync_end 547 v_blanking: 562 v_border: 0
[    10.826] (II) fglrx(0): Number of EDID sections to follow: 1
[    10.826] (II) fglrx(0): EDID (in hex):
[    10.826] (II) fglrx(0): 	00ffffffffffff00410c000001010101
[    10.826] (II) fglrx(0): 	03140103808048780ae692a3544a9926
[    10.826] (II) fglrx(0): 	0f4a4c2108008bc08180a94001010101
[    10.826] (II) fglrx(0): 	010101010101023a801871382d40582c
[    10.826] (II) fglrx(0): 	450000d05200001e023a80d072382d40
[    10.826] (II) fglrx(0): 	102c458000d05200001e000000fc0050
[    10.826] (II) fglrx(0): 	68696c697073204654560a20000000fd
[    10.826] (II) fglrx(0): 	00303e0f4611000a20202020202001c9
[    10.827] (II) fglrx(0): Printing probed modes for output DFP5
[    10.827] (II) fglrx(0): Modeline "1920x1080"x60.0  148.50  1920 2008 2052 2200  1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
////
///
//// (je coupe les Modelines car j'ai trop de caractères pour pouvoir poster)
[    10.827] (II) fglrx(0): EDID for output DFP6
[    10.827] (II) fglrx(0): EDID for output DFP7
[    10.827] (II) fglrx(0): EDID for output CRT1
[    10.827] (II) fglrx(0): Manufacturer: HSD  Model: 1c2b  Serial#: 933
[    10.827] (II) fglrx(0): Year: 2008  Week: 17
[    10.827] (II) fglrx(0): EDID Version: 1.3
[    10.827] (II) fglrx(0): Analog Display Input,  Input Voltage Level: 0.700/0.300 V
[    10.827] (II) fglrx(0): Sync:  Separate  SyncOnGreen
[    10.827] (II) fglrx(0): Max Image Size [cm]: horiz.: 41  vert.: 26
[    10.827] (II) fglrx(0): Gamma: 2.20
[    10.827] (II) fglrx(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display
[    10.827] (II) fglrx(0): First detailed timing is preferred mode
[    10.827] (II) fglrx(0): redX: 0.643 redY: 0.325   greenX: 0.295 greenY: 0.616
[    10.827] (II) fglrx(0): blueX: 0.143 blueY: 0.081   whiteX: 0.310 whiteY: 0.330
[    10.827] (II) fglrx(0): Supported established timings:
[    10.827] (II) fglrx(0): 720x400@70Hz
/// (suppression pour pas dépasser la limite max de caractère)
[    10.827] (II) fglrx(0): Manufacturer's mask: 0
[    10.827] (II) fglrx(0): Supported standard timings:
[    10.827] (II) fglrx(0): #0: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
[    10.827] (II) fglrx(0): #1: hsize: 1280  vsize 720  refresh: 60  vid: 49281
[    10.827] (II) fglrx(0): #2: hsize: 1280  vsize 960  refresh: 60  vid: 16513
[    10.827] (II) fglrx(0): #3: hsize: 1152  vsize 864  refresh: 75  vid: 20337
[    10.827] (II) fglrx(0): #4: hsize: 1024  vsize 768  refresh: 66  vid: 18017
[    10.827] (II) fglrx(0): #5: hsize: 1400  vsize 1050  refresh: 75  vid: 20368
[    10.827] (II) fglrx(0): #6: hsize: 1440  vsize 900  refresh: 75  vid: 3989
[    10.827] (II) fglrx(0): Supported detailed timing:
[    10.827] (II) fglrx(0): clock: 106.5 MHz   Image Size:  408 x 255 mm
[    10.827] (II) fglrx(0): h_active: 1440  h_sync: 1520  h_sync_end 1672 h_blank_end 1904 h_border: 0
[    10.827] (II) fglrx(0): v_active: 900  v_sync: 903  v_sync_end 909 v_blanking: 934 v_border: 0
[    10.827] (II) fglrx(0): Ranges: V min: 55 V max: 75 Hz, H min: 30 H max: 83 kHz, PixClock max 145 MHz
[    10.827] (II) fglrx(0): Serial No: 817PA3BY00933
[    10.827] (II) fglrx(0): Monitor name: Hanns.G HG191
[    10.827] (II) fglrx(0): EDID (in hex):
[    10.827] (II) fglrx(0): 	00ffffffffffff0022642b1ca5030000
[    10.827] (II) fglrx(0): 	111201030a291a78ea9bb6a4534b9d24
[    10.827] (II) fglrx(0): 	144f54bfef80818081c08140714f6146
[    10.827] (II) fglrx(0): 	904f950f01019a29a0d0518422305098
[    10.827] (II) fglrx(0): 	360098ff1000001e000000fd00374b1e
[    10.827] (II) fglrx(0): 	530e000a202020202020000000ff0038
[    10.827] (II) fglrx(0): 	313750413342593030393333000000fc
[    10.827] (II) fglrx(0): 	0048616e6e732e4720484731393100de
[    10.827] (II) fglrx(0): User Preference Output CRT1 using refresh rate 60.0 Hz.
[    10.827] (II) fglrx(0): Printing probed modes for output CRT1
[    10.827] (II) fglrx(0): Modeline "1440x900"x60.0  106.50  1440 1520 1672 1904  900 903 909 934 +hsync +vsync (55.9 kHz UeP)
///
/// (idem)
[    10.827] (II) fglrx(0): Output DFP1 disconnected
[    10.827] (II) fglrx(0): Output DFP2 disconnected
[    10.827] (II) fglrx(0): Output DFP3 disconnected
[    10.827] (II) fglrx(0): Output DFP4 disconnected
[    10.827] (II) fglrx(0): Output DFP5 disabled by config file
[    10.827] (II) fglrx(0): Output DFP6 disconnected
[    10.827] (II) fglrx(0): Output DFP7 disconnected
[    10.827] (II) fglrx(0): Output CRT1 connected
[    10.827] (II) fglrx(0): Using user preference for initial modes
[    10.827] (II) fglrx(0): Output CRT1 using initial mode 1440x900
[    10.827] (II) fglrx(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[    10.827] (II) fglrx(0): DPI set to (96, 96)
[    10.827] (II) fglrx(0): Eyefinity capable adapter detected.
[    10.827] (II) fglrx(0): Adapter AMD Radeon R9 200 Series has 6 configurable heads and 2 displays connected.
[    10.827] (==) fglrx(0):  PseudoColor visuals disabled
[    10.827] (II) Loading sub module "ramdac"
[    10.827] (II) LoadModule: "ramdac"
[    10.827] (II) Module "ramdac" already built-in
[    10.827] (==) fglrx(0): NoDRI = NO
[    10.827] (==) fglrx(0): Capabilities: 0x00000000
[    10.827] (==) fglrx(0): CapabilitiesEx: 0x00000000
[    10.827] (==) fglrx(0): OpenGL ClientDriverName: "fglrx_dri.so"
[    10.827] (==) fglrx(0): UseFastTLS=0
[    10.827] (II) fglrx(0): Shadow Primary option: ShadowPrimary is enabled
[    10.827] (--) Depth 24 pixmap format is 32 bpp
[    10.827] Loading extension ATIFGLRXDRI
[    10.827] (II) fglrx(0): doing swlDriScreenInit
[    10.828] (II) fglrx(0): swlDriScreenInit for fglrx driver
[    10.828] ukiDynamicMajor: found major device number 250
[    10.828] ukiDynamicMajor: found major device number 250
[    10.828] ukiDynamicMajor: found major device number 250
[    10.828] ukiOpenByBusid: Searching for BusID PCI:1:0:0
[    10.828] ukiOpenDevice: node name is /dev/ati/card0
[    10.828] ukiOpenDevice: open result is 12, (OK)
[    10.828] ukiOpenByBusid: ukiOpenMinor returns 12
[    10.828] ukiOpenByBusid: ukiGetBusid reports PCI:1:0:0
[    10.828] (II) fglrx(0): [uki] DRM interface version 1.0
[    10.828] (II) fglrx(0): [uki] created "fglrx" driver at busid "PCI:1:0:0"
[    10.828] (II) fglrx(0): [uki] added 8192 byte SAREA at 0x2000
[    10.828] (II) fglrx(0): [uki] mapped SAREA 0x2000 to 0x7fd91b0f8000
[    10.828] (II) fglrx(0): [uki] framebuffer handle = 0x3000
[    10.828] (II) fglrx(0): [uki] added 1 reserved context for kernel
[    10.828] (II) fglrx(0): swlDriScreenInit done
[    10.828] (II) fglrx(0): Kernel Module Version Information:
[    10.828] (II) fglrx(0):     Name: fglrx
[    10.828] (II) fglrx(0):     Version: 13.35.5
[    10.828] (II) fglrx(0):     Date: Jan 29 2014
[    10.828] (II) fglrx(0):     Desc: AMD FireGL DRM kernel module
[    10.828] (II) fglrx(0): Kernel Module version matches driver.
[    10.828] (II) fglrx(0): Kernel Module Build Time Information:
[    10.828] (II) fglrx(0):     Build-Kernel UTS_RELEASE:        3.13.5-1-ARCH
[    10.828] (II) fglrx(0):     Build-Kernel MODVERSIONS:        yes
[    10.828] (II) fglrx(0):     Build-Kernel __SMP__:            yes
[    10.828] (II) fglrx(0):     Build-Kernel PAGE_SIZE:          0x1000
[    10.828] (II) fglrx(0): [uki] register handle = 0x00004000
[    10.846] (II) fglrx(0): Display width adjusted to to 1536 due to alignment constraints
[    10.846] (II) fglrx(0): DRI initialization successfull
[    10.855] (II) fglrx(0): FBADPhys: 0xf400000000 FBMappedSize: 0x01140000
[    10.866] (==) fglrx(0): Backing store enabled
[    10.866] Loading extension FGLRXEXTENSION
[    10.866] (==) fglrx(0): DPMS enabled
[    10.866] (II) fglrx(0): Initialized in-driver Xinerama extension
[    10.866] (**) fglrx(0): Textured Video is enabled.
[    10.866] (II) LoadModule: "glesx"
[    10.866] (II) Loading /usr/lib/xorg/modules/glesx.so
[    10.977] (II) Module glesx: vendor="X.Org Foundation"
[    10.977] 	compiled for 1.4.99.906, module version = 1.0.0
[    10.977] Loading extension GLESX
[    10.977] (II) fglrx(0): GLESX enableFlags = 8784
[    10.978] (II) fglrx(0): GLESX is enabled
[    10.978] (II) LoadModule: "amdxmm"
[    10.978] (II) Loading /usr/lib/xorg/modules/amdxmm.so
[    10.996] (II) Module amdxmm: vendor="X.Org Foundation"
[    10.996] 	compiled for 1.4.99.906, module version = 2.0.0
[    11.013] Loading extension AMDXVOPL
[    11.013] Loading extension AMDXVBA
[    11.021] (II) fglrx(0): UVD feature is enabled(II) fglrx(0): 
[    11.021] (II) fglrx(0): Enable composite support successfully
[    11.021] (II) fglrx(0): X context handle = 0x1
[    11.021] (II) fglrx(0): [DRI] installation complete
[    11.021] (==) fglrx(0): Silken mouse enabled
[    11.022] (==) fglrx(0): Using HW cursor of display infrastructure!
[    11.022] (II) fglrx(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[    11.161] (--) RandR disabled
[    11.180] ukiDynamicMajor: found major device number 250
[    11.180] ukiDynamicMajor: found major device number 250
[    11.180] ukiOpenByBusid: Searching for BusID PCI:1:0:0
[    11.180] ukiOpenDevice: node name is /dev/ati/card0
[    11.180] ukiOpenDevice: open result is 13, (OK)
[    11.180] ukiOpenByBusid: ukiOpenMinor returns 13
[    11.180] ukiOpenByBusid: ukiGetBusid reports PCI:1:0:0
[    11.180] (EE) AIGLX error: failed to open /usr/X11R6/lib64/modules/dri/fglrx_dri.so, error[/usr/X11R6/lib64/modules/dri/fglrx_dri.so: cannot open shared object file: No such file or directory]
[    11.415] ukiDynamicMajor: found major device number 250
[    11.415] ukiDynamicMajor: found major device number 250
[    11.415] ukiDynamicMajor: found major device number 250
[    11.415] ukiOpenDevice: node name is /dev/ati/card0
[    11.415] ukiOpenDevice: open result is 14, (OK)
[    11.415] ukiGetBusid returned 'PCI:1:0:0'
[    11.415] ukiOpenDevice: node name is /dev/ati/card1
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: Open failed
[    11.415] ukiOpenDevice: node name is /dev/ati/card2
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: Open failed
[    11.415] ukiOpenDevice: node name is /dev/ati/card3
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: Open failed
[    11.415] ukiOpenDevice: node name is /dev/ati/card4
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: Open failed
[    11.415] ukiOpenDevice: node name is /dev/ati/card5
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: Open failed
[    11.415] ukiOpenDevice: node name is /dev/ati/card6
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: Open failed
[    11.415] ukiOpenDevice: node name is /dev/ati/card7
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: Open failed
[    11.415] ukiOpenDevice: node name is /dev/ati/card8
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: Open failed
[    11.415] ukiOpenDevice: node name is /dev/ati/card9
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: Open failed
[    11.415] ukiOpenDevice: node name is /dev/ati/card10
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: Open failed
[    11.415] ukiOpenDevice: node name is /dev/ati/card11
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: Open failed
[    11.415] ukiOpenDevice: node name is /dev/ati/card12
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: Open failed
[    11.415] ukiOpenDevice: node name is /dev/ati/card13
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: Open failed
[    11.415] ukiOpenDevice: node name is /dev/ati/card14
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: Open failed
[    11.415] ukiOpenDevice: node name is /dev/ati/card15
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: open result is -1, (No such device)
[    11.415] ukiOpenDevice: Open failed
[    11.416] ukiDynamicMajor: found major device number 250
[    11.416] ukiOpenByBusid: Searching for BusID PCI:1:0:0
[    11.416] ukiOpenDevice: node name is /dev/ati/card0
[    11.416] ukiOpenDevice: open result is 14, (OK)
[    11.416] ukiOpenByBusid: ukiOpenMinor returns 14
[    11.416] ukiOpenByBusid: ukiGetBusid reports PCI:1:0:0
[    11.931] (II) AIGLX: Loaded and initialized OpenGL driver(II) GLX: Initialized DRI GL provider for screen 0
[    11.932] ukiDynamicMajor: found major device number 250
[    11.932] ukiDynamicMajor: found major device number 250
[    11.932] ukiDynamicMajor: found major device number 250
[    11.932] ukiOpenDevice: node name is /dev/ati/card0
[    11.932] ukiOpenDevice: open result is 15, (OK)
[    11.932] ukiGetBusid returned 'PCI:1:0:0'
[    11.932] ukiOpenDevice: node name is /dev/ati/card1
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: Open failed
[    11.932] ukiOpenDevice: node name is /dev/ati/card2
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: Open failed
[    11.932] ukiOpenDevice: node name is /dev/ati/card3
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: Open failed
[    11.932] ukiOpenDevice: node name is /dev/ati/card4
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: Open failed
[    11.932] ukiOpenDevice: node name is /dev/ati/card5
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: Open failed
[    11.932] ukiOpenDevice: node name is /dev/ati/card6
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: Open failed
[    11.932] ukiOpenDevice: node name is /dev/ati/card7
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: Open failed
[    11.932] ukiOpenDevice: node name is /dev/ati/card8
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: Open failed
[    11.932] ukiOpenDevice: node name is /dev/ati/card9
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: Open failed
[    11.932] ukiOpenDevice: node name is /dev/ati/card10
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: Open failed
[    11.932] ukiOpenDevice: node name is /dev/ati/card11
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: Open failed
[    11.932] ukiOpenDevice: node name is /dev/ati/card12
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: Open failed
[    11.932] ukiOpenDevice: node name is /dev/ati/card13
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: Open failed
[    11.932] ukiOpenDevice: node name is /dev/ati/card14
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: Open failed
[    11.932] ukiOpenDevice: node name is /dev/ati/card15
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: open result is -1, (No such device)
[    11.932] ukiOpenDevice: Open failed
[    11.932] ukiDynamicMajor: found major device number 250
[    11.932] ukiOpenByBusid: Searching for BusID PCI:1:0:0
[    11.932] ukiOpenDevice: node name is /dev/ati/card0
[    11.932] ukiOpenDevice: open result is 15, (OK)
[    11.932] ukiOpenByBusid: ukiOpenMinor returns 15
[    11.932] ukiOpenByBusid: ukiGetBusid reports PCI:1:0:0
[    12.027] (II) fglrx(0): OverDrive5 Detected!
[    12.029] (II) fglrx(0): Setting screen physical size to 381 x 238
[    12.344] (II) config/udev: Adding input device Power Button (/dev/input/event4)
[    12.344] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    12.344] (**) Power Button: Applying InputClass "Keyboard Layout"
[    12.344] (**) Power Button: Applying InputClass "Keyboard Terminate"
[    12.344] (II) LoadModule: "evdev"
[    12.344] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    12.355] (II) Module evdev: vendor="X.Org Foundation"
[    12.355] 	compiled for 1.15.0, module version = 2.8.2
[    12.355] 	Module class: X.Org XInput Driver
[    12.355] 	ABI class: X.Org XInput driver, version 20.0
[    12.355] (II) Using input driver 'evdev' for 'Power Button'
[    12.355] (**) Power Button: always reports core events
[    12.355] (**) evdev: Power Button: Device: "/dev/input/event4"
[    12.355] (--) evdev: Power Button: Vendor 0 Product 0x1
[    12.355] (--) evdev: Power Button: Found keys
[    12.355] (II) evdev: Power Button: Configuring as keyboard
[    12.355] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4/event4"
[    12.355] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[    12.355] (**) Option "xkb_rules" "evdev"
[    12.355] (**) Option "xkb_model" "pc104"
[    12.355] (**) Option "xkb_layout" "fr"
[    12.355] (**) Option "xkb_variant" "latin9"
[    12.355] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[    12.380] (II) config/udev: Adding input device Power Button (/dev/input/event3)
[    12.380] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    12.380] (**) Power Button: Applying InputClass "Keyboard Layout"
[    12.380] (**) Power Button: Applying InputClass "Keyboard Terminate"
[    12.380] (II) Using input driver 'evdev' for 'Power Button'
[    12.380] (**) Power Button: always reports core events
[    12.380] (**) evdev: Power Button: Device: "/dev/input/event3"
[    12.380] (--) evdev: Power Button: Vendor 0 Product 0x1
[    12.380] (--) evdev: Power Button: Found keys
[    12.380] (II) evdev: Power Button: Configuring as keyboard
[    12.380] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3/event3"
[    12.380] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[    12.380] (**) Option "xkb_rules" "evdev"
[    12.380] (**) Option "xkb_model" "pc104"
[    12.380] (**) Option "xkb_layout" "fr"
[    12.380] (**) Option "xkb_variant" "latin9"
[    12.380] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[    12.381] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=3 (/dev/input/event16)
[    12.381] (II) No input driver specified, ignoring this device.
[    12.381] (II) This device may have been added with another device file.
[    12.381] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=7 (/dev/input/event15)
[    12.381] (II) No input driver specified, ignoring this device.
[    12.381] (II) This device may have been added with another device file.
[    12.381] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=8 (/dev/input/event14)
[    12.381] (II) No input driver specified, ignoring this device.
[    12.381] (II) This device may have been added with another device file.
[    12.381] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=9 (/dev/input/event13)
[    12.381] (II) No input driver specified, ignoring this device.
[    12.381] (II) This device may have been added with another device file.
[    12.381] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=10 (/dev/input/event12)
[    12.381] (II) No input driver specified, ignoring this device.
[    12.381] (II) This device may have been added with another device file.
[    12.381] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=11 (/dev/input/event11)
[    12.381] (II) No input driver specified, ignoring this device.
[    12.381] (II) This device may have been added with another device file.
[    12.381] (II) config/udev: Adding input device Microsoft Basic Optical Mouse (/dev/input/event0)
[    12.381] (**) Microsoft Basic Optical Mouse: Applying InputClass "evdev pointer catchall"
[    12.381] (II) Using input driver 'evdev' for 'Microsoft Basic Optical Mouse'
[    12.381] (**) Microsoft Basic Optical Mouse: always reports core events
[    12.381] (**) evdev: Microsoft Basic Optical Mouse: Device: "/dev/input/event0"
[    12.381] (--) evdev: Microsoft Basic Optical Mouse: Vendor 0x45e Product 0x84
[    12.381] (--) evdev: Microsoft Basic Optical Mouse: Found 3 mouse buttons
[    12.381] (--) evdev: Microsoft Basic Optical Mouse: Found scroll wheel(s)
[    12.381] (--) evdev: Microsoft Basic Optical Mouse: Found relative axes
[    12.381] (--) evdev: Microsoft Basic Optical Mouse: Found x and y relative axes
[    12.381] (II) evdev: Microsoft Basic Optical Mouse: Configuring as mouse
[    12.381] (II) evdev: Microsoft Basic Optical Mouse: Adding scrollwheel support
[    12.381] (**) evdev: Microsoft Basic Optical Mouse: YAxisMapping: buttons 4 and 5
[    12.381] (**) evdev: Microsoft Basic Optical Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    12.381] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-6/1-6:1.0/input/input0/event0"
[    12.381] (II) XINPUT: Adding extended input device "Microsoft Basic Optical Mouse" (type: MOUSE, id 8)
[    12.381] (II) evdev: Microsoft Basic Optical Mouse: initialized for relative axes.
[    12.381] (**) Microsoft Basic Optical Mouse: (accel) keeping acceleration scheme 1
[    12.381] (**) Microsoft Basic Optical Mouse: (accel) acceleration profile 0
[    12.381] (**) Microsoft Basic Optical Mouse: (accel) acceleration factor: 2.000
[    12.381] (**) Microsoft Basic Optical Mouse: (accel) acceleration threshold: 4
[    12.382] (II) config/udev: Adding input device Microsoft Basic Optical Mouse (/dev/input/mouse0)
[    12.382] (II) No input driver specified, ignoring this device.
[    12.382] (II) This device may have been added with another device file.
[    12.382] (II) config/udev: Adding input device Logitech USB Keyboard (/dev/input/event1)
[    12.382] (**) Logitech USB Keyboard: Applying InputClass "evdev keyboard catchall"
[    12.382] (**) Logitech USB Keyboard: Applying InputClass "Keyboard Layout"
[    12.382] (**) Logitech USB Keyboard: Applying InputClass "Keyboard Terminate"
[    12.382] (II) Using input driver 'evdev' for 'Logitech USB Keyboard'
[    12.382] (**) Logitech USB Keyboard: always reports core events
[    12.382] (**) evdev: Logitech USB Keyboard: Device: "/dev/input/event1"
[    12.382] (--) evdev: Logitech USB Keyboard: Vendor 0x46d Product 0xc31d
[    12.382] (--) evdev: Logitech USB Keyboard: Found keys
[    12.382] (II) evdev: Logitech USB Keyboard: Configuring as keyboard
[    12.382] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-9/1-9:1.0/input/input1/event1"
[    12.382] (II) XINPUT: Adding extended input device "Logitech USB Keyboard" (type: KEYBOARD, id 9)
[    12.382] (**) Option "xkb_rules" "evdev"
[    12.382] (**) Option "xkb_model" "pc104"
[    12.382] (**) Option "xkb_layout" "fr"
[    12.382] (**) Option "xkb_variant" "latin9"
[    12.382] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[    12.382] (II) config/udev: Adding input device Logitech USB Keyboard (/dev/input/event2)
[    12.382] (**) Logitech USB Keyboard: Applying InputClass "evdev keyboard catchall"
[    12.382] (**) Logitech USB Keyboard: Applying InputClass "Keyboard Layout"
[    12.382] (**) Logitech USB Keyboard: Applying InputClass "Keyboard Terminate"
[    12.382] (II) Using input driver 'evdev' for 'Logitech USB Keyboard'
[    12.382] (**) Logitech USB Keyboard: always reports core events
[    12.382] (**) evdev: Logitech USB Keyboard: Device: "/dev/input/event2"
[    12.382] (--) evdev: Logitech USB Keyboard: Vendor 0x46d Product 0xc31d
[    12.382] (--) evdev: Logitech USB Keyboard: Found absolute axes
[    12.382] (II) evdev: Logitech USB Keyboard: Forcing absolute x/y axes to exist.
[    12.382] (--) evdev: Logitech USB Keyboard: Found keys
[    12.382] (II) evdev: Logitech USB Keyboard: Forcing relative x/y axes to exist.
[    12.382] (II) evdev: Logitech USB Keyboard: Configuring as mouse
[    12.382] (II) evdev: Logitech USB Keyboard: Configuring as keyboard
[    12.382] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-9/1-9:1.1/input/input2/event2"
[    12.382] (II) XINPUT: Adding extended input device "Logitech USB Keyboard" (type: KEYBOARD, id 10)
[    12.382] (**) Option "xkb_rules" "evdev"
[    12.382] (**) Option "xkb_model" "pc104"
[    12.382] (**) Option "xkb_layout" "fr"
[    12.382] (**) Option "xkb_variant" "latin9"
[    12.382] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[    12.382] (II) evdev: Logitech USB Keyboard: initialized for absolute axes.
[    12.382] (**) Logitech USB Keyboard: (accel) keeping acceleration scheme 1
[    12.382] (**) Logitech USB Keyboard: (accel) acceleration profile 0
[    12.382] (**) Logitech USB Keyboard: (accel) acceleration factor: 2.000
[    12.382] (**) Logitech USB Keyboard: (accel) acceleration threshold: 4
[    12.382] (II) config/udev: Adding input device HDA Intel PCH Front Headphone (/dev/input/event6)
[    12.382] (II) No input driver specified, ignoring this device.
[    12.382] (II) This device may have been added with another device file.
[    12.382] (II) config/udev: Adding input device HDA Intel PCH Front Mic (/dev/input/event10)
[    12.382] (II) No input driver specified, ignoring this device.
[    12.382] (II) This device may have been added with another device file.
[    12.382] (II) config/udev: Adding input device HDA Intel PCH Rear Mic (/dev/input/event9)
[    12.382] (II) No input driver specified, ignoring this device.
[    12.382] (II) This device may have been added with another device file.
[    12.383] (II) config/udev: Adding input device HDA Intel PCH Line (/dev/input/event8)
[    12.383] (II) No input driver specified, ignoring this device.
[    12.383] (II) This device may have been added with another device file.
[    12.383] (II) config/udev: Adding input device HDA Intel PCH Line Out (/dev/input/event7)
[    12.383] (II) No input driver specified, ignoring this device.
[    12.383] (II) This device may have been added with another device file.
[    12.383] (II) config/udev: Adding input device Eee PC WMI hotkeys (/dev/input/event17)
[    12.383] (**) Eee PC WMI hotkeys: Applying InputClass "evdev keyboard catchall"
[    12.383] (**) Eee PC WMI hotkeys: Applying InputClass "Keyboard Layout"
[    12.383] (**) Eee PC WMI hotkeys: Applying InputClass "Keyboard Terminate"
[    12.383] (II) Using input driver 'evdev' for 'Eee PC WMI hotkeys'
[    12.383] (**) Eee PC WMI hotkeys: always reports core events
[    12.383] (**) evdev: Eee PC WMI hotkeys: Device: "/dev/input/event17"
[    12.383] (--) evdev: Eee PC WMI hotkeys: Vendor 0 Product 0
[    12.383] (--) evdev: Eee PC WMI hotkeys: Found keys
[    12.383] (II) evdev: Eee PC WMI hotkeys: Configuring as keyboard
[    12.383] (**) Option "config_info" "udev:/sys/devices/platform/eeepc-wmi/input/input17/event17"
[    12.383] (II) XINPUT: Adding extended input device "Eee PC WMI hotkeys" (type: KEYBOARD, id 11)
[    12.383] (**) Option "xkb_rules" "evdev"
[    12.383] (**) Option "xkb_model" "pc104"
[    12.383] (**) Option "xkb_layout" "fr"
[    12.383] (**) Option "xkb_variant" "latin9"
[    12.383] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[    12.383] (II) config/udev: Adding input device PC Speaker (/dev/input/event5)
[    12.383] (II) No input driver specified, ignoring this device.
[    12.383] (II) This device may have been added with another device file.
[    12.386] (II) fglrx(0): Restoring Recent Mode via PCS is not supported in RANDR 1.2 capable environments
[    52.769] (II) fglrx(0): EDID vendor "HSD", prod id 7211
[    52.769] (II) fglrx(0): Using EDID range info for horizontal sync
[    52.769] (II) fglrx(0): Using EDID range info for vertical refresh
[    52.769] (II) fglrx(0): Printing DDC gathered Modelines:
[    52.769] (II) fglrx(0): Modeline "1440x900"x0.0  106.50  1440 1520 1672 1904  900 903 909 934 +hsync +vsync (55.9 kHz eP)
////
//// (idem)
[    52.769] (II) fglrx(0): User Preference Output CRT1 using refresh rate 60.0 Hz.
[  4539.330] (II) fglrx(0): EDID vendor "HSD", prod id 7211
[  4539.330] (II) fglrx(0): Using hsync ranges from config file
[  4539.330] (II) fglrx(0): Using vrefresh ranges from config file
[  4539.330] (II) fglrx(0): Printing DDC gathered Modelines:
[  4539.330] (II) fglrx(0): Modeline "1440x900"x0.0  106.50  1440 1520 1672 1904  900 903 909 934 +hsync +vsync (55.9 kHz eP)
////
//// (idem)
[  4539.330] (II) fglrx(0): Modeline "1440x900"x0.0  136.75  1440 1536 1688 1936  900 903 909 942 -hsync +vsync (70.6 kHz e)
[  4539.330] (II) fglrx(0): User Preference Output CRT1 using refresh rate 60.0 Hz.
[  4539.335] (II) fglrx(0): EDID vendor "HSD", prod id 7211
[  4539.335] (II) fglrx(0): Using hsync ranges from config file
[  4539.335] (II) fglrx(0): Using vrefresh ranges from config file
[  4539.335] (II) fglrx(0): Printing DDC gathered Modelines:
[  4539.335] (II) fglrx(0): Modeline "1440x900"x0.0  106.50  1440 1520 1672 1904  900 903 909 934 +hsync +vsync (55.9 kHz eP)
////
////
//// (idem)
[  4539.335] (II) fglrx(0): Modeline "1440x900"x0.0  136.75  1440 1536 1688 1936  900 903 909 942 -hsync +vsync (70.6 kHz e)
[  4539.335] (II) fglrx(0): User Preference Output CRT1 using refresh rate 60.0 Hz.
Perso je pense que les drivers AMD linux ne gèrent tout simplement pas bien ma carte au niveau des effets 3D et que j'ai plus qu'à attendre une hypothétique mise à jour qui me permettra de jouer sous linux. Mais si quelqu'un a une autre théorie ou si quelqu'un a une carte r9 270X tournant avec les pilotes AMD sous linux je suis preneur ^^

Si vous voulez d'autres logs n'hésitez pas à demander. Par contre indiquez-moi juste où les trouver car vu le peu de log présent dans /var/log par rapport à une debian je me dis qu'il doit y en avoir ailleurs.

Merci :)

Re: [Catalyst] Serveur X plante

Publié : jeu. 27 févr. 2014, 02:17
par antynea
bonjour,

Sans pouvoir t'aider, mais juste en prenant quelques minutes :

https://aur.archlinux.org/packages/cata ... mments=all

Depuis les drivers 14.xxx, voir antérieur, le server X, crash....

Personnellement je tourne toujours sur les drivers 13.11, aucun crash répertorié à première vue.

Peut-être devrais-tu investiguer plus en profondeur de ce côté là.

Aimablement,
Anty

Re: [Catalyst] Serveur X plante

Publié : jeu. 27 févr. 2014, 07:00
par fate
Merci pour l'info, je verrai ce soir pour downgrader xorg-server et installer la version stable des drivers (et croiser les doigts ^^)

Re: [Catalyst] Serveur X plante

Publié : jeu. 27 févr. 2014, 19:53
par antynea
tu es libre penseurs de tes actions, je ne faisais que t'informer....
Edit: si quelqu'un de plus compétent que moi passe par ici, libre à lui de nous informer et de nous diriger sur la bonne voie
Ainsi soit-il :)

Re: [Catalyst] Serveur X plante

Publié : ven. 28 févr. 2014, 21:47
par fate
J'ai installé les drivers stable (13.12) et comme je m'en doutais (pour avoir testé les drivers stable sous debian) j'ai exactement les même problèmes. Est-ce que quelqu'un sur ce forum possède une R9 270X par le plus grand des hasards ?
Fuseau horaire sur UTC+02:00
Page 1 sur 1

Développé par phpBB® Forum Software © phpBB Limited

Traduction française officielle © Qiaeru