Page 1 sur 1
[smartmontools] smartctl ne voie pas plus les températures de sdb et sdd (contourné)
Publié : mar. 25 janv. 2022, 16:36
par ignace72
Bonjour à tous.
smartctl ne voie pas plus les températures de sdb et sdd pourtant, sous Windows 7, leurs capteurs de températures fonctionnent.
J'utilise avec Hddtemp et voilà sa configuration dans /etc/systemd/system/hddtemp.service :
Code : Tout sélectionner
[Unit]
Description=Hard drive temperature monitor daemon
[Service]
ExecStart=/usr/bin/hddtemp --daemon --foreground -n /dev/sda /dev/sdb /dev/sdc /dev/sdd
[Install]
WantedBy=multi-user.target --listen=127.0.0.1
Si quelqu'un peut m'aider.
Merci.
Ignace.
Re: [smartmontools] smartctl ne voie pas plus les températures de sdb et sdd
Publié : mar. 25 janv. 2022, 19:54
par benjarobin
Bonjour,
Qu'est-ce que fait
--listen=127.0.0.1
sur la ligne de
WantedBy=multi-user.target
?
Ce fichier semble assez invalide... La ligne de
ExecStart=
devrait ressemblait plus à cela :
Code : Tout sélectionner
ExecStart=/usr/bin/hddtemp --daemon --foreground --listen=127.0.0.1 /dev/sda /dev/sdb /dev/sdc /dev/sdd
Voir / Lire aussi le wiki
https://wiki.archlinux.org/title/Hddtemp
Sinon que je sache smartctl et hddtemp n'ont aucun lien. Tu as vu ceci où ?
Re: [smartmontools] smartctl ne voie pas plus les températures de sdb et sdd
Publié : mar. 25 janv. 2022, 21:18
par ignace72
Bonsoir, benjarobin.
Ben le lien, c'est que hddtemp lit ce que lui donne smartmontools.
Ignace.
Re: [smartmontools] smartctl ne voie pas plus les températures de sdb et sdd
Publié : mar. 25 janv. 2022, 22:40
par benjarobin
Non, j'ai vérifié le code est cela me semble faux... Ce sont 2 projets complètement indépendant... Les 2 envois des commandes smart, oui, mais le lien s'arrête là.
Je veux bien que tu me prouve le contraire avec lien à l'appui... Mais les dépendances des paquets "prouvent" déjà le contraire...
Re: [smartmontools] smartctl ne voie pas plus les températures de sdb et sdd
Publié : mar. 25 janv. 2022, 22:50
par ignace72
Oui, enfin cela ne résout pas mon problème plutôt que savoir le lien entre smartctl et hddtemp.
Ignace.
Re: [smartmontools] smartctl ne voie pas plus les températures de sdb et sdd
Publié : mar. 25 janv. 2022, 23:31
par benjarobin
Sauf que l'on ne sait pas où est le problème... Tu parles de 2 choses sans lien, et on ne sait pas vraiment quoi pose problème, quelle commande tu as exécuté, ...
Quelle est la commande exacte qui ne te retourne plus la température ? Plus de détail serait appréciable (à part cela ne marche pas...)
Par exemple quelle est la sortie complète (en root) pour chacun de tes disques (même ceux "fonctionnels") de :
Re: [smartmontools] smartctl ne voie pas plus les températures de sdb et sdd
Publié : mer. 26 janv. 2022, 00:51
par ignace72
Ok, ça, je peux faire.
J'ai changé l'ordre des disques, car j'ai eu un problème de partition et j'ai du rajouter un disque.
Donc :
le premier disque :
Code : Tout sélectionner
[ignace@ignace-pc ~]$ sudo smartctl -a /dev/sda
[sudo] Mot de passe de ignace :
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.2-1-MANJARO] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD40EFRX-68WT0N0
Serial Number: WD-WCC4E0976998
LU WWN Device Id: 5 0014ee 209c45bee
Firmware Version: 80.00A80
User Capacity: 4 000 787 030 016 bytes [4,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Wed Jan 26 00:36:47 2022 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (55260) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 552) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x703d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 292
3 Spin_Up_Time 0x0027 176 171 021 Pre-fail Always - 8175
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 172
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 008 008 000 Old_age Always - 67374
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 166
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 106
193 Load_Cycle_Count 0x0032 195 195 000 Old_age Always - 16401
194 Temperature_Celsius 0x0022 112 104 000 Old_age Always - 40
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 9
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 10 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Pour le second disque :
Code : Tout sélectionner
[ignace@ignace-pc ~]$ sudo smartctl -a /dev/sdb
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.2-1-MANJARO] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD80EFAX-68KNBN0
Serial Number: VDH7K8ED
LU WWN Device Id: 5 000cca 0bbd186f0
Firmware Version: 81.00A81
User Capacity: 8 001 563 222 016 bytes [8,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Wed Jan 26 00:38:16 2022 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 87) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 850) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0004 128 128 054 Old_age Offline - 108
3 Spin_Up_Time 0x0007 211 211 024 Pre-fail Always - 461 (Average 311)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 42
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000a 100 100 067 Old_age Always - 0
8 Seek_Time_Performance 0x0004 128 128 020 Old_age Offline - 18
9 Power_On_Hours 0x0012 099 099 000 Old_age Always - 12877
10 Spin_Retry_Count 0x0012 100 100 060 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 42
192 Power-Off_Retract_Count 0x0032 082 082 000 Old_age Always - 22503
193 Load_Cycle_Count 0x0012 082 082 000 Old_age Always - 22503
194 Temperature_Celsius 0x0002 151 151 000 Old_age Always - 43 (Min/Max 25/50)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Pour le troisième disque, attention, celui-là n'a pas de capteur de température :
Code : Tout sélectionner
[ignace@ignace-pc ~]$ sudo smartctl -a /dev/sdc
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.2-1-MANJARO] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital RE4
Device Model: WDC WD5003ABYX-01WERA2
Serial Number: WD-WMAYP7648375
LU WWN Device Id: 5 0014ee 0ae6c34d7
Firmware Version: 01.01S03
User Capacity: 500 107 862 016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Wed Jan 26 00:39:32 2022 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 8160) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 83) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 192 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 144 142 021 Pre-fail Always - 3775
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 164
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 009 009 000 Old_age Always - 67010
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 162
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 104
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 115
194 Temperature_Celsius 0x0022 111 099 000 Old_age Always - 32
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Aborted by host 70% 2 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, r
If Selective self-test is pending on power-up, resume after 0 minute delay.
Pour le quatrième disque :
Code : Tout sélectionner
[ignace@ignace-pc ~]$ sudo smartctl -a /dev/sdd
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.2-1-MANJARO] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Samsung based SSDs
Device Model: Samsung SSD 860 PRO 512GB
Serial Number: S42YNX0R900179V
LU WWN Device Id: 5 002538 e419000e0
Firmware Version: RVM02B6Q
User Capacity: 512 110 190 592 bytes [512 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
TRIM Command: Available, deterministic, zeroed
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Wed Jan 26 00:41:53 2022 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x53) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 85) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 121
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 10
177 Wear_Leveling_Count 0x0013 100 100 000 Pre-fail Always - 0
179 Used_Rsvd_Blk_Cnt_Tot 0x0013 100 100 010 Pre-fail Always - 0
181 Program_Fail_Cnt_Total 0x0032 100 100 010 Old_age Always - 0
182 Erase_Fail_Count_Total 0x0032 100 100 010 Old_age Always - 0
183 Runtime_Bad_Block 0x0013 100 100 010 Pre-fail Always - 0
187 Uncorrectable_Error_Cnt 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0032 068 062 000 Old_age Always - 32
195 ECC_Error_Rate 0x001a 200 200 000 Old_age Always - 0
199 CRC_Error_Count 0x003e 099 099 000 Old_age Always - 12
235 POR_Recovery_Count 0x0012 099 099 000 Old_age Always - 5
241 Total_LBAs_Written 0x0032 099 099 000 Old_age Always - 168054502
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Pour le cinquième disque :
Code : Tout sélectionner
[ignace@ignace-pc ~]$ sudo smartctl -a /dev/sde
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.2-1-MANJARO] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Re
Device Model: WDC WD3000FYYZ-01UL1B2
Serial Number: WD-WCC135RF5UUN
LU WWN Device Id: 5 0014ee 20c7ccfe3
Firmware Version: 01.01K03
User Capacity: 3 000 592 982 016 bytes [3,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Wed Jan 26 00:43:06 2022 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (34320) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 372) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x70bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 145 140 021 Pre-fail Always - 11725
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 136
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 027 027 000 Old_age Always - 53299
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 130
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 76
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 59
194 Temperature_Celsius 0x0022 113 104 000 Old_age Always - 39
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Aborted by host 90% 48466 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Voilà.
Merci pour ton aide.
Ignace.
Re: [smartmontools] smartctl ne voie pas plus les températures de sdb et sdd
Publié : mer. 26 janv. 2022, 08:13
par benjarobin
Donc, tous les disques sans aucune exception (malgré que tu ai indiqué le contraire pour le 3ieme) retournent une température qui semble valide.
Je vais donc reposer la question, comme malheureusement tu n'y as pas répondu :
Quelle est la commande exacte qui ne te retourne plus la température ? Plus de détail serait appréciable (à part cela ne marche pas...)
Re: [smartmontools] smartctl ne voie pas plus les températures de sdb et sdd
Publié : mer. 26 janv. 2022, 10:21
par ignace72
Ha oui, je viens de remarquer que ça refonctionne avec le moniteur de capteurs de XFce.
Pour le quatrième, la commande (sudo smartctl -a /dev/sdd), c'est la même commande que j'avais utilisée pour voir si ça marchait ou pas.
Mais là, au test que je viens encore de refaire, la commande n'indique que « Airflow_Temperature_Cel » :
Code : Tout sélectionner
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 121
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 10
177 Wear_Leveling_Count 0x0013 100 100 000 Pre-fail Always - 0
179 Used_Rsvd_Blk_Cnt_Tot 0x0013 100 100 010 Pre-fail Always - 0
181 Program_Fail_Cnt_Total 0x0032 100 100 010 Old_age Always - 0
182 Erase_Fail_Count_Total 0x0032 100 100 010 Old_age Always - 0
183 Runtime_Bad_Block 0x0013 100 100 010 Pre-fail Always - 0
187 Uncorrectable_Error_Cnt 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0032 068 062 000 Old_age Always - 32
195 ECC_Error_Rate 0x001a 200 200 000 Old_age Always - 0
199 CRC_Error_Count 0x003e 099 099 000 Old_age Always - 12
235 POR_Recovery_Count 0x0012 099 099 000 Old_age Always - 5
241 Total_LBAs_Written 0x0032 099 099 000 Old_age Always - 168054502
Pour l'autre disque dons je n'avais pas la température, j'avais la même sortie. Pourtant, juste avant que j'ouvre le fil, le moniteur de capteurs de XFce ne me proposait que trois disques.
Je n'y comprends rien. Je n'ai rien touché à la configuration de Smartmontools.
Je peux donc mettre le fil en résolu.
Ignace.
Re: [smartmontools] smartctl ne voie pas plus les températures de sdb et sdd (en cours)
Publié : jeu. 27 janv. 2022, 15:59
par ignace72
Bonjour à tous.
Le problème recommence, mais là, j'ai un message d'erreur, j'ai ça comme réponse à la commande sudo smartctl -a /dev/sdd :
Code : Tout sélectionner
[ignace@ignace-pc ~]$ sudo smartctl -a /dev/sdd
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.2-1-MANJARO] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Samsung based SSDs
Device Model: Samsung SSD 860 PRO 512GB
Serial Number: S42YNX0R900179V
Firmware Version: RVM02B6Q
User Capacity: 512 110 190 592 bytes [512 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 (minor revision not indicated)
Local Time is: Thu Jan 27 15:55:14 2022 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x00) Offline data collection not supported.
SMART capabilities: (0x0000) Automatic saving of SMART data is not implemented.
Error logging capability: (0x00) Error logging NOT supported.
No General Purpose Logging support.
SMART Error Log not supported
SMART Self-test Log not supported
Selective Self-tests/Logging not supported
J'ai deux contrôleurs SATA, et je me demande si un ne serait pas en train de lâcher.
Ignace.
Re: [smartmontools] smartctl ne voie pas plus les températures de sdb et sdd (en cours)
Publié : jeu. 27 janv. 2022, 22:42
par ignace72
Bon, j'ai changé de contrôleur SATA et ça me donne :
Code : Tout sélectionner
[ignace@ignace-pc ~]$ sudo smartctl -a /dev/sdc
[sudo] Mot de passe de ignace :
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.2-1-MANJARO] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Samsung based SSDs
Device Model: Samsung SSD 860 PRO 512GB
Serial Number: S42YNX0R900179V
LU WWN Device Id: 5 002538 e419000e0
Firmware Version: RVM02B6Q
User Capacity: 512 110 190 592 bytes [512 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
TRIM Command: Available, deterministic, zeroed
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Thu Jan 27 22:37:33 2022 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x53) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 85) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 166
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 13
177 Wear_Leveling_Count 0x0013 100 100 000 Pre-fail Always - 0
179 Used_Rsvd_Blk_Cnt_Tot 0x0013 100 100 010 Pre-fail Always - 0
181 Program_Fail_Cnt_Total 0x0032 100 100 010 Old_age Always - 0
182 Erase_Fail_Count_Total 0x0032 100 100 010 Old_age Always - 0
183 Runtime_Bad_Block 0x0013 100 100 010 Pre-fail Always - 0
187 Uncorrectable_Error_Cnt 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0032 064 057 000 Old_age Always - 36
195 ECC_Error_Rate 0x001a 200 200 000 Old_age Always - 0
199 CRC_Error_Count 0x003e 099 099 000 Old_age Always - 12
235 POR_Recovery_Count 0x0012 099 099 000 Old_age Always - 5
241 Total_LBAs_Written 0x0032 099 099 000 Old_age Always - 173722812
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
J'ai redémarré sur Windows pour vérifier et le capteur fonctionne.
Ignace.
Re: [smartmontools] smartctl ne voie pas plus les températures de sdb et sdd (en cours)
Publié : ven. 28 janv. 2022, 16:21
par ignace72
Bonjour à tous.
J'ai des nouvelles.
Smartmontools ne me trouve toujours pas la température de mon SSD mais par-contre le module noyau drivetemp me trouve bien les températures de mes quatre disques durs dons le SSD.
Je vais donc laisser tomber la méthode avec Smartmontools et Hddtemp et passer par le module drivetemp.
Ignace.