Reconnaissance et configuration du matériel / kernel linux
killruana
newbie
Messages : 7 Inscription : ven. 12 sept. 2008, 21:31
Message
par killruana » ven. 12 sept. 2008, 21:42
Bonjour,
j'ai acheté une carte wifi PCMCIA TP-LINK TL-WN310G et qui n'ai pas reconnu :/
J'ai installé les drivers mdwifi et rajouté options ath_pci countrycode=250 dans /etc/modprobe.con
Infos utiles :
Code : Tout sélectionner
[killruana@Wishmaster ~]$ lspci
(...)
02:00.0 Ethernet controller: Atheros Communications Inc. Device 001d (rev 01)
Code : Tout sélectionner
[killruana@Wishmaster ~]$ lspci -v
(...)
02:00.0 Ethernet controller: Atheros Communications Inc. Device 001d (rev 01)
Subsystem: Atheros Communications Inc. Device 1055
Flags: medium devsel, IRQ 5
Memory at 44000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel modules: ath_pci
Code : Tout sélectionner
[killruana@Wishmaster ~]$ lsmod | egrep "ath"
ath_pci 241848 0
wlan 222192 1 ath_pci
ath_hal 250976 1 ath_pci
Code : Tout sélectionner
[killruana@Wishmaster ~]$ dmesg | egrep "(ath|wifi)"
ath_hal: module license 'Proprietary' taints kernel.
ath_pci 0000:02:00.0: enabling device (0000 -> 0002)
ath_pci: HAL doesn't support MAC revision 0xf0
Si quelqu'un à une odée...
Dernière modification par
killruana le sam. 13 sept. 2008, 00:42, modifié 1 fois.
Skunnyk
Maître du Kyudo
Messages : 1137 Inscription : mer. 06 sept. 2006, 21:31
Localisation : IRC
Contact :
Message
par Skunnyk » ven. 12 sept. 2008, 21:55
Hello ,
Elle semble pourtant reconnu d'après les logs.
Un iwconfig et un ifconfig -a ne te donne rien ?
ps: hum, cette carte n'a pas l'air très repandu, tu peux toujours tenter du coté de ndiswrapper si tu ne t'en sors pas :/
killruana
newbie
Messages : 7 Inscription : ven. 12 sept. 2008, 21:31
Message
par killruana » ven. 12 sept. 2008, 22:07
Code : Tout sélectionner
[killruana@Wishmaster ~]$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
[killruana@Wishmaster ~]$ ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:C0:9F:31:C4:27
inet addr:192.168.1.12 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::2c0:9fff:fe31:c427/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:226887 errors:0 dropped:0 overruns:0 frame:0
TX packets:126400 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:329369685 (314.1 Mb) TX bytes:9964518 (9.5 Mb)
Interrupt:4 Base address:0x1800
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:24 errors:0 dropped:0 overruns:0 frame:0
TX packets:24 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1200 (1.1 Kb) TX bytes:1200 (1.1 Kb)
Je l'ai essayé sur d'autres distrib, et elle n'est reconnue/utilisable que sur backtrack 3 :/
Quand à ndiswrapper, j'aimerais eviter si d'autres solutions existent
killruana
newbie
Messages : 7 Inscription : ven. 12 sept. 2008, 21:31
Message
par killruana » ven. 12 sept. 2008, 22:20
Ca marche avec Ndiswrapper.
Faute de mieux, je vais m'en contenter...
Merci quand même
(mais si vous avez une autre solution, ne vous genez pas)
Tebo
Chu Ko Nu
Messages : 368 Inscription : sam. 17 mars 2007, 23:24
Message
par Tebo » ven. 12 sept. 2008, 23:26
Si le chip fait partie de la serie 5xxx
tu peut essayer avec ath5k
Code : Tout sélectionner
modinfo ath5k
filename: /lib/modules/2.6.26-T60/kernel/drivers/net/wireless/ath5k/ath5k.ko
version: 0.5.0 (EXPERIMENTAL)
license: Dual BSD/GPL
description: Support for 5xxx series of Atheros 802.11 wireless LAN cards.
intégrer dans la quenelle depuis le 2.6.25 j'croit, mais bon ..
killruana
newbie
Messages : 7 Inscription : ven. 12 sept. 2008, 21:31
Message
par killruana » ven. 12 sept. 2008, 23:27
J'ai un autre problème, avec netcfg cette fois-çi :
Code : Tout sélectionner
[killruana@Wishmaster ~]$ sudo netcfg2 wlan0.Livebox-2334.static
Password:
> Livebox-2334 is not a valid connection, check spelling or look at examples
mon fichier de config est :
Code : Tout sélectionner
[killruana@Wishmaster ~]$ cat /etc/network.d/wlan0.Livebox-2334.static
CONNECTION="Livebox-2334"
DESCRIPTION="A wep encrypted wireless connection using static ip"
INTERFACE=wlan0
SCAN="yes"
SECURITY="wep"
ESSID="Livebox-2334"
KEY="xxx"
IP="static"
IFOPTS="192.168.1.30 netmask 255.255.255.0 broadcast 192.168.1.255"
GATEWAY="192.168.1.1"
DNS1=192.168.1.1
D'où vient l'erreur ? Je me suis servis des exemples de configuration pourtant :/
Skunnyk
Maître du Kyudo
Messages : 1137 Inscription : mer. 06 sept. 2006, 21:31
Localisation : IRC
Contact :
Message
par Skunnyk » ven. 12 sept. 2008, 23:55
Dans CONNECTION; il faut mettre le type de connexion.
Donc ici ca serait wireless
CONNECTION="wireless"
killruana
newbie
Messages : 7 Inscription : ven. 12 sept. 2008, 21:31
Message
par killruana » sam. 13 sept. 2008, 00:42
Skunnyk a écrit : Dans CONNECTION; il faut mettre le type de connexion.
Donc ici ca serait wireless
CONNECTION="wireless"
Après quelqes essais j'ai trouvé tout seul
Je suis un peu boulet parfois
Mais merci quand meme pour ton aide
titoucha
Daikyu
Messages : 81 Inscription : mar. 02 sept. 2008, 16:58
Localisation : Genève
Message
par titoucha » sam. 13 sept. 2008, 05:32
Et tu as trouvé quoi comme solution, ça m'intéresse.