en fait je les avais déja mis sur le forum:
bon alors:
dans /etc/ppp
j'ai mis mon mot de passe et identifiant dans chap-secrets et dans pap-secrets
ensuite dans /etc/ppp//peers
"monidentifiant"
mru 1492
mtu 1492
noipdefault
defaultroute
usepeerdns
noauth
#ipcp-accept-remote
#ipcp-accept-local
nobsdcomp
nodeflate
nopcomp
novj
novjccomp
noaccomp -am
persist
updetach
pty "/usr/local/sbin/fctStartAdsl -i"
/etc/.rc.conf
#
# /etc/rc.conf - Main Configuration for Arch Linux
#
#
# -----------------------------------------------------------------------
# LOCALIZATION
# -----------------------------------------------------------------------
#
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/unimaps
# USECOLOR: use ANSI color sequences in startup messages
#
LOCALE="fr_FR.UTF-8"
HARDWARECLOCK="localtime"
TIMEZONE="Europe/Paris"
KEYMAP="fr"
CONSOLEFONT="lat9w-16"
CONSOLEMAP="8859-15"
USECOLOR="yes"
CONSOLETRANSLATION="8859-15_to_uni"
#
# -----------------------------------------------------------------------
# HARDWARE
# -----------------------------------------------------------------------
#
# Scan hardware and load required modules at bootup
MOD_AUTOLOAD="yes"
# Module Blacklist - modules in this list will never be loaded by hwdetect
MOD_BLACKLIST=(eagle-usb)
#
# Modules to load at boot-up (in this order)
# - prefix a module with a ! to disable it
#
MODULES=(usbserial usblp usbcore usblp pppoatm ppp_async usbatm
ueagle_atm snd-via82xx)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
#
# -----------------------------------------------------------------------
# NETWORKING
# -----------------------------------------------------------------------
#
HOSTNAME="myhost"
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
#
# Note: to use DHCP, set your interface to be "dhcp" (eth0="dhcp")
#
lo="lo 127.0.0.1"
#eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
#INTERFACES=(lo eth0="dhcp")
#
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
#
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
#
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up
# - prefix an entry with a ! to disable it
#
# Network profiles are found in /etc/network-profiles
#
#NET_PROFILES=(main)
#
# -----------------------------------------------------------------------
# DAEMONS
# -----------------------------------------------------------------------
#
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
#
DAEMONS=(ppp pppd network syslog-ng @cupsd @cups autofs udev alsa
hwd
!hotplug kdm !pcmcia !netfs crond ueagle)
# End of file
et pour lancer la connection au démarrage:
http://forums.archlinux.fr/viewtopic.ph ... highlight=
Ne pas oublier de décompresser les firmwares
http://forum.eagle-usb.org/viewtopic.php?t=4169
et voilou, tu dois avoir à peu pret tout
![Wink :wink:](./images/smilies/icon_e_wink.gif)