Je suis actuellement en train d'installer Archlinux sur une carte KEEK-2030 (Atom N270 + Bridge ICH7M).
Après avoir observé des problèmes de FrameRate sur mes webcams, je me suis penché sur le bus PCI et me suis rendu compte que mes Device était reconnu en Full Speed (aussi bien mes Webcam que mes Clefs USB 2.0).
Au niveau du lspci, l'usb est détecté correctement (je pense) :
Code : Tout sélectionner
00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integrated Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1e.2 Multimedia audio controller: Intel Corporation 82801G (ICH7 Family) AC'97 Audio Controller (rev 02)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02)
01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8110SC/8169SC Gigabit Ethernet (rev 10)
Code : Tout sélectionner
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usb 2-2: configuration #1 chosen from 1 choice
usb 2-2: reset full speed USB device using uhci_hcd and address 3
Code : Tout sélectionner
BIOS EBDA/lowmem at: 0009fc00/0009fc00
Linux version 2.6.28-ARCH (root@T-POWA-LX) (gcc version 4.3.3 (GCC) ) #1 SMP PREEMPT Sun Mar 8 10:18:28 UTC 2009
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
NSC Geode by NSC
Cyrix CyrixInstead
Centaur CentaurHauls
Transmeta GenuineTMx86
Transmeta TransmetaCPU
UMC UMC UMC UMC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003f7a0000 (usable)
BIOS-e820: 000000003f7a0000 - 000000003f7ae000 (ACPI data)
BIOS-e820: 000000003f7ae000 - 000000003f7ffaa0 (ACPI NVS)
BIOS-e820: 000000003f7ffaa0 - 000000003f800000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
DMI present.
AMI BIOS detected: BIOS may corrupt low RAM, working it around.
last_pfn = 0x3f7a0 max_arch_pfn = 0x100000
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Scanning 0 areas for low memory corruption
modified physical RAM map:
modified: 0000000000000000 - 0000000000010000 (reserved)
modified: 0000000000010000 - 000000000009fc00 (usable)
modified: 000000000009fc00 - 00000000000a0000 (reserved)
modified: 00000000000e0000 - 0000000000100000 (reserved)
modified: 0000000000100000 - 000000003f7a0000 (usable)
modified: 000000003f7a0000 - 000000003f7ae000 (ACPI data)
modified: 000000003f7ae000 - 000000003f7ffaa0 (ACPI NVS)
modified: 000000003f7ffaa0 - 000000003f800000 (reserved)
modified: 00000000fee00000 - 00000000fee01000 (reserved)
modified: 00000000fff00000 - 0000000100000000 (reserved)
kernel direct mapping tables up to 377fe000 @ 10000-16000
RAMDISK: 3f720000 - 3f78f207
Allocated new RAMDISK: 00012000 - 00081207
Move RAMDISK from 000000003f720000 - 000000003f78f206 to 00012000 - 00081206
ACPI: RSDP 000F97F0, 0014 (r0 ACPIAM)
ACPI: RSDT 3F7A0000, 003C (r1 022309 RSDT1117 20090223 MSFT 97)
ACPI: FACP 3F7A0200, 0084 (r1 022309 FACP1117 20090223 MSFT 97)
ACPI: DSDT 3F7A0430, 4E1B (r1 1ADZU 1ADZU005 5 INTL 20051117)
ACPI: FACS 3F7AE000, 0040
ACPI: APIC 3F7A0390, 005C (r1 022309 APIC1117 20090223 MSFT 97)
ACPI: MCFG 3F7A03F0, 003C (r1 022309 OEMMCFG 20090223 MSFT 97)
ACPI: OEMB 3F7AE040, 0072 (r1 022309 OEMB1117 20090223 MSFT 97)
ACPI: ASF! 3F7AA430, 0075 (r32 LEGEND I865PASF 1 INTL 20051117)
ACPI: SSDT 3F7AEA00, 04F0 (r1 PmRef CpuPm 3000 INTL 20051117)
ACPI: Local APIC address 0xfee00000
127MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 00000000 - 377fe000
bootmap 00082000 - 00088f00
(9 early reservations) ==> bootmem [0000000000 - 00377fe000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0000100000 - 000056cb20] TEXT DATA BSS ==> [0000100000 - 000056cb20]
#4 [000056d000 - 0000570000] INIT_PG_TABLE ==> [000056d000 - 0000570000]
#5 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
#6 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000]
#7 [0000012000 - 0000081207] NEW RAMDISK ==> [0000012000 - 0000081207]
#8 [0000082000 - 0000089000] BOOTMAP ==> [0000082000 - 0000089000]
found SMP MP-table at [c00ff780] 000ff780
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x0003f7a0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x0003f7a0
On node 0 totalpages: 259887
free_area_init_node: node 0, pgdat c0415a00, node_mem_map c1000200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3951 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 256 pages used for memmap
HighMem zone: 32418 pages, LIFO batch:7
Movable zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at 40000000 (gap: 3f800000:bf600000)
PERCPU: Allocating 36864 bytes of per cpu data
NR_CPUS: 16, nr_cpu_ids: 2, nr_node_ids 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 257855
Kernel command line: root=/dev/disk/by-uuid/504a513d-4eee-402c-92e0-34edd7d5124d ro
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Fast TSC calibration using PIT
Detected 1600.027 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Scanning for low memory corruption every 60 seconds
Memory: 1025160k/1040000k available (2281k kernel code, 14032k reserved, 1033k data, 336k init, 130696k highmem)
virtual kernel memory layout:
fixmap : 0xffee8000 - 0xfffff000 (1116 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc0443000 - 0xc0497000 ( 336 kB)
.data : 0xc033a797 - 0xc043cbdc (1033 kB)
.text : 0xc0100000 - 0xc033a797 (2281 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Calibrating delay loop (skipped), value calculated using timer frequency.. 3201.38 BogoMIPS (lpj=5333423)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 24K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
using mwait in idle threads.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20080926
ACPI: Checking initramfs for custom DSDT
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Atom(TM) CPU N270 @ 1.60GHz stepping 02
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3201.14 BogoMIPS (lpj=5333036)
CPU: L1 I cache: 32K, L1 D cache: 24K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Atom(TM) CPU N270 @ 1.60GHz stepping 02
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (6402.53 BogoMIPS).
net_namespace: 768 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 63
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=1
PCI: Using configuration type 1 for base access
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 63
PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
PCI: Using MMCONFIG for extended config space
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:02.0: reg 10 32bit mmio: [0xfea80000-0xfeafffff]
pci 0000:00:02.0: reg 14 io port: [0xdc80-0xdc87]
pci 0000:00:02.0: reg 18 32bit mmio: [0xd0000000-0xdfffffff]
pci 0000:00:02.0: reg 1c 32bit mmio: [0xfea40000-0xfea7ffff]
pci 0000:00:02.1: reg 10 32bit mmio: [0xfe980000-0xfe9fffff]
pci 0000:00:1d.0: reg 20 io port: [0xdc00-0xdc1f]
pci 0000:00:1d.1: reg 20 io port: [0xd880-0xd89f]
pci 0000:00:1d.2: reg 20 io port: [0xd800-0xd81f]
pci 0000:00:1d.3: reg 20 io port: [0xd480-0xd49f]
pci 0000:00:1e.2: reg 10 io port: [0xd000-0xd0ff]
pci 0000:00:1e.2: reg 14 io port: [0xd400-0xd43f]
pci 0000:00:1e.2: reg 18 32bit mmio: [0xfea3bc00-0xfea3bdff]
pci 0000:00:1e.2: reg 1c 32bit mmio: [0xfea3b800-0xfea3b8ff]
pci 0000:00:1e.2: PME# supported from D0 D3hot D3cold
pci 0000:00:1e.2: PME# disabled
pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
pci 0000:00:1f.2: reg 10 io port: [0x00-0x07]
pci 0000:00:1f.2: reg 14 io port: [0x00-0x03]
pci 0000:00:1f.2: reg 18 io port: [0x00-0x07]
pci 0000:00:1f.2: reg 1c io port: [0x00-0x03]
pci 0000:00:1f.2: reg 20 io port: [0xffa0-0xffaf]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f]
pci 0000:01:04.0: reg 10 io port: [0xec00-0xecff]
pci 0000:01:04.0: reg 14 32bit mmio: [0xfebffc00-0xfebffcff]
pci 0000:01:04.0: reg 30 32bit mmio: [0xfebc0000-0xfebdffff]
pci 0000:01:04.0: supports D1 D2
pci 0000:01:04.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:01:04.0: PME# disabled
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge io port: [0xe000-0xefff]
pci 0000:00:1e.0: bridge 32bit mmio: [0xfeb00000-0xfebfffff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 7A, should be B7 [20080926]
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet clockevent registered
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:06: IRQ 4 override to edge, high
pnp 00:07: IRQ 4 override to edge, high
pnp 00:08: IRQ 11 override to edge, high
pnp 00:09: IRQ 11 override to edge, high
pnp: PnP ACPI: found 17 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
system 00:0a: ioport range 0x4d0-0x4d1 has been reserved
system 00:0a: ioport range 0x800-0x87f has been reserved
system 00:0a: ioport range 0x480-0x4bf has been reserved
system 00:0a: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:0a: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:0a: iomem range 0xfed40000-0xfed8ffff has been reserved
system 00:0b: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0b: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:0e: ioport range 0xa00-0xa0f has been reserved
system 00:0e: ioport range 0xa10-0xa1f has been reserved
system 00:0e: ioport range 0xa20-0xa2f has been reserved
system 00:0e: ioport range 0xa30-0xa3f has been reserved
system 00:0f: iomem range 0xe0000000-0xe3ffffff has been reserved
system 00:10: iomem range 0x0-0x9ffff could not be reserved
system 00:10: iomem range 0xc0000-0xcffff could not be reserved
system 00:10: iomem range 0xe0000-0xfffff could not be reserved
system 00:10: iomem range 0x100000-0x3f7fffff could not be reserved
system 00:10: iomem range 0xfed90000-0xffffffff could not be reserved
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01
pci 0000:00:1e.0: IO window: 0xe000-0xefff
pci 0000:00:1e.0: MEM window: 0xfeb00000-0xfebfffff
pci 0000:00:1e.0: PREFETCH window: 0x00000040000000-0x000000400fffff
pci 0000:00:1e.0: setting latency timer to 64
bus: 00 index 0 io port: [0x00-0xffff]
bus: 00 index 1 mmio: [0x000000-0xffffffff]
bus: 01 index 0 io port: [0xe000-0xefff]
bus: 01 index 1 mmio: [0xfeb00000-0xfebfffff]
bus: 01 index 2 mmio: [0x40000000-0x400fffff]
bus: 01 index 3 io port: [0x00-0xffff]
bus: 01 index 4 mmio: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs... done
Freeing initrd memory: 444k freed
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
type=2000 audit(1237893326.383:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1748
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:02.0: Boot video device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A
serial8250: ttyS3 at I/O 0x2e8 (irq = 3) is a 16550A
00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS1 at I/O 0x2f8 (irq = 4) is a 16550A
00:08: ttyS2 at I/O 0x3e8 (irq = 11) is a 16550A
00:09: ttyS3 at I/O 0x2e8 (irq = 11) is a 16550A
input: Macintosh mouse button emulation as /class/input/input0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 336k freed
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
input: AT Translated Set 2 keyboard as /class/input/input1
SCSI subsystem initialized
libata version 3.00 loaded.
ata_piix 0000:00:1f.2: version 2.12
ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
ata_piix 0000:00:1f.2: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
ata1.00: ATA-7: Maxtor 6V080E0, VA111900, max UDMA/133
ata1.00: 160086528 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA Maxtor 6V080E0 VA11 PQ: 0 ANSI: 5
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 160086528 512-byte hardware sectors: (81.9 GB/76.3 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 160086528 512-byte hardware sectors: (81.9 GB/76.3 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
rtc_cmos 00:03: RTC can wake from S4
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, 114 bytes nvram, hpet irqs
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ndiswrapper version 1.54 loaded (smp=yes, preempt=yes)
usbcore: registered new interface driver ndiswrapper
Linux video capture interface: v2.00
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
usbcore: registered new interface driver usbtouchscreen
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
ACPI: SSDT 3F7AE190, 023C (r1 PmRef Cpu0Ist 3000 INTL 20051117)
ACPI: SSDT 3F7AE460, 0594 (r1 PmRef Cpu0Cst 3001 INTL 20051117)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Monitor-Mwait will be used to enter C-3 state
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
processor ACPI_CPU:00: registered as cooling_device0
ACPI: SSDT 3F7AE0C0, 00CC (r1 PmRef Cpu1Ist 3000 INTL 20051117)
ACPI: SSDT 3F7AE3D0, 0085 (r1 PmRef Cpu1Cst 3000 INTL 20051117)
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
processor ACPI_CPU:01: registered as cooling_device1
Marking TSC unstable due to TSC halts in idle
ACPI Warning (nspredef-0858): \_TZ_.THRM._TZD: Return Package type mismatch at index 0 - found Processor, expected Reference [20080926]
ACPI: Expecting a [Reference] package element, found type C
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (55 C)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Linux agpgart interface v0.103
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000dc00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d880
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000d480
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
iTCO_vendor_support: vendor-support=0
agpgart-intel 0000:00:00.0: Intel 945GME Chipset
agpgart-intel 0000:00:00.0: detected 7932K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: Found a ICH7-M or ICH7-U TCO device (Version=2, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
usb 1-2: new full speed USB device using uhci_hcd and address 2
intel_rng: FWH not detected
Intel ICH 0000:00:1e.2: PCI INT A -> GSI 17 (level, low) -> IRQ 17
Intel ICH 0000:00:1e.2: setting latency timer to 64
usb 1-2: configuration #1 chosen from 1 choice
usb 2-1: new low speed USB device using uhci_hcd and address 2
sd 0:0:0:0: Attached scsi generic sg0 type 0
input: PC Speaker as /class/input/input4
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:01:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
r8169 0000:01:04.0: no PCI Express capability
eth0: RTL8169sc/8110sc at 0xf8244c00, 00:50:08:02:ba:07, XID 18000000 IRQ 16
intel8x0_measure_ac97_clock: measured 50256 usecs
intel8x0: clocking to 48000
i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19
input: Video Bus as /class/input/input5
ACPI: Video Device [IGD] (multi-head: yes rom: no post: no)
usb 2-1: configuration #1 chosen from 1 choice
Error: Driver 'pcspkr' is already registered, aborting...
input: eGalax Inc. as /class/input/input6
psmouse serio1: ID: 00 00 3c<6>elantech.c: unexpected magic knock result 0x1a, 0x03, 0x3c.
usb 2-2: new full speed USB device using uhci_hcd and address 3
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usb 2-2: configuration #1 chosen from 1 choice
usb 2-2: reset full speed USB device using uhci_hcd and address 3
input: ImPS/2 Logitech Wheel Mouse as /class/input/input7
ndiswrapper: driver rt73 (Ralink,10/21/2008, 1.03.02.0000) loaded
wlan0: ethernet device 00:0e:8e:1d:a7:c6 using NDIS driver: rt73, version: 0x0, NDIS version: 0x500, vendor: 'IEEE 802.11g Wireless Card.', 148F:2573.F.conf
wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK
scsi 2:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 0 CCS
warning: `syslog-ng' uses 32-bit capabilities (legacy support in use)
sd 2:0:0:0: [sdb] 2015232 512-byte hardware sectors: (1.03 GB/984 MiB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] 2015232 512-byte hardware sectors: (1.03 GB/984 MiB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 2:0:0:0: [sdb] Attached SCSI removable disk
sd 2:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
Merci d'avance pour votre aide,
WinZ.
