[carte wifi] Plus possible de se connecter (contourné)

[silmaa]

Bonjour,

J'ai fait une MAJ avant hier (pacman -Syu) et depuis, impossible de me connecter à ma freebox... Le wifi n'a jamais très bien fonctionné avec Arch sur mon PC(pertes de connexion, lenteurs déraisonnables, impossibilités de se connecter etc.), mais là c'est carrément mort.

Voici quelques détails...

Code : Tout sélectionner

#ma carte wifi
lispci -v
09:00.0 Network controller: Intel Corporation Centrino Wireless-N 1030 (rev 34)
	Subsystem: Intel Corporation Centrino Wireless-N 1030 BGN
	Flags: bus master, fast devsel, latency 0, IRQ 53
	Memory at f7a00000 (64-bit, non-prefetchable) [size=8K]
	Capabilities: <access denied>
	Kernel driver in use: iwlagn
	Kernel modules: iwlagn

#mon rc.conf
[...]
interface=wlan0
address=
netmask=
broadcast=
gateway=
[...]
DAEMONS=(dbus networkmanager hwclock syslog-ng hal ivman netfs crond ifplugd cups)

J'ai tenté de me connecté manuelle car je n'avais absolument espérant avoir un message d'erreur quelque part, mais rien :

Code : Tout sélectionner

$ sudo iwlist wlan0 scan
          Cell 03 - Address: 4A:5B:8D:F3:5D:88
                    Channel:11
                    Frequency:2.462 GHz (Channel 11)
                    Quality=66/70  Signal level=-44 dBm  
                    Encryption key:on
                    ESSID:"Freebox"
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s
                              18 Mb/s; 36 Mb/s; 54 Mb/s
                    Bit Rates:6 Mb/s; 12 Mb/s; 24 Mb/s; 48 Mb/s
                    Mode:Master
                    Extra:tsf=0000000165de113d
                    Extra: Last beacon: 46ms ago
                    IE: Unknown: 000946726565626F783236
                    IE: Unknown: 010882848B961224486C
                    IE: Unknown: 03010B
                    IE: Unknown: 2A0104
                    IE: Unknown: 32040C183060
                    IE: Unknown: 2D1A6E1017FFFF000001000000000000000000000000000000000000
                    IE: Unknown: 3D160B070700000000000000000000000000000000000000
                    IE: Unknown: 3E0100
                    IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00
                    IE: Unknown: 7F0101
                    IE: Unknown: DD07000C4300000000
                    IE: Unknown: DD1E00904C336E1017FFFF000001000000000000000000000000000000000000
                    IE: Unknown: DD1A00904C340B070700000000000000000000000000000000000000

$ sudo iwconfig wlan0 mode managed channel 11 key 1456-913A-40 essid Freebox
#et là rien ne se passe, pas un message, rien.
$

Comme c'est venu apres une MAJ, je vous mets aussi le log de pacman un peu élagué parce la la MAJ de LaTeX prend de la place :

Code : Tout sélectionner

[2011-12-26 00:46] Running 'pacman -Syu'
[2011-12-26 00:46] synchronizing package lists
[2011-12-26 00:46] starting full system upgrade
[2011-12-26 01:14] Running 'pacman -Sf filesystem'
[2011-12-26 01:14] upgraded filesystem (2011.10-1 -> 2011.12-2)
[2011-12-26 01:15] Running 'pacman -Syu'
[2011-12-26 01:15] synchronizing package lists
[2011-12-26 01:15] starting full system upgrade
[2011-12-26 01:16] upgraded libldap (2.4.26-5 -> 2.4.28-1)
[2011-12-26 01:16] upgraded unixodbc (2.3.0-2 -> 2.3.1-1)
[2011-12-26 01:16] upgraded apr-util (1.3.12-3 -> 1.3.12-4)
[2011-12-26 01:16] upgraded automake (1.11.1-3 -> 1.11.2-1)
[2011-12-26 01:16] upgraded bluez (4.96-1 -> 4.96-3)
[2011-12-26 01:17] upgraded ca-certificates (20111025-2 -> 20111211-1)
[2011-12-26 01:17] upgraded nss (3.12.11-3 -> 3.13.1-1)
[2011-12-26 01:17] upgraded chromium (15.0.874.121-1 -> 16.0.912.63-1)
[2011-12-26 01:17] Generating locales...
[2011-12-26 01:17]   en_US.UTF-8... done
[2011-12-26 01:17]   en_US.ISO-8859-1... done
[2011-12-26 01:17]   fr_FR.UTF-8... done
[2011-12-26 01:17] Generation complete.
[2011-12-26 01:17] upgraded glibc (2.14.1-2 -> 2.14.1-4)
[2011-12-26 01:17] upgraded sdl (1.2.14-9 -> 1.2.14-10)
[2011-12-26 01:17] upgraded ffmpeg (20111123-1 -> 20111211-1)
[2011-12-26 01:17] upgraded firefox (8.0.1-1 -> 9.0.1-1)
[2011-12-26 01:17] upgraded telepathy-glib (0.16.3-1 -> 0.16.4-1)
[2011-12-26 01:17] upgraded folks (0.6.5-1 -> 0.6.6-1)
[2011-12-26 01:17] upgraded libjpeg-turbo (1.1.1-3 -> 1.1.1-4)
[2011-12-26 01:17] upgraded gdk-pixbuf2 (2.24.0-1 -> 2.24.1-1)
[2011-12-26 01:17] upgraded gmime (2.4.28-1 -> 2.4.29-1)
[2011-12-26 01:17] upgraded libxi (1.4.3-1 -> 1.4.5-1)
[2011-12-26 01:17] upgraded gtk3 (3.2.2-3 -> 3.2.3-1)
[2011-12-26 01:17] upgraded gnome-keyring (3.2.2-1 -> 3.2.2-3)
[2011-12-26 01:17] upgraded gnutls (3.0.8-1 -> 3.0.9-1)
[2011-12-26 01:17] upgraded gtk-xfce-engine (2.9.0-1 -> 2.99.0-1)
[2011-12-26 01:17] upgraded lcms2 (2.2-1 -> 2.3-1)
[2011-12-26 01:17] upgraded imagemagick (6.7.3.8-1 -> 6.7.4.0-1)
[2011-12-26 01:17] upgraded initscripts (2011.11.3-1 -> 2011.12.1-1)
[2011-12-26 01:17] upgraded jack (0.121.3-4 -> 0.121.3-5)
[2011-12-26 01:17] upgraded jre7-openjdk (7.b147_2.0-2 -> 7.b147_2.0-4)
[2011-12-26 01:17] upgraded jdk7-openjdk (7.b147_2.0-2 -> 7.b147_2.0-4)
[2011-12-26 01:17] upgraded strigi (0.7.6-2 -> 0.7.7-1)
[2011-12-26 01:17] upgraded qt (4.7.4-3 -> 4.8.0-2)
[2011-12-26 01:17] upgraded polkit-qt (0.99.0-1 -> 0.103.0-1)
[2011-12-26 01:17] upgraded phonon (1:4.5.1-2 -> 1:4.6.0-1)
[2011-12-26 01:17] upgraded texinfo (4.13a-6 -> 4.13a-7)
[2011-12-26 01:17] installed gperf (3.0.4-4)
[2011-12-26 01:17] installed qtwebkit (2.2.1-1)
[2011-12-26 01:17] upgraded kdelibs (4.7.4-1 -> 4.7.4-2)
[2011-12-26 01:17] upgraded lib32-glibc (2.14.1-2 -> 2.14.1-4)
[2011-12-26 01:17] upgraded lib32-attr (2.4.46-1 -> 2.4.46-2)
[2011-12-26 01:17] upgraded libdrm (2.4.28-1 -> 2.4.29-1)
[2011-12-26 01:17] upgraded lib32-libdrm (2.4.27-2 -> 2.4.29-1)
[2011-12-26 01:17] upgraded lib32-libglapi (7.11.2-1 -> 7.11.2-2)
[2011-12-26 01:17] upgraded lib32-libgl (7.11.2-1 -> 7.11.2-2)
[2011-12-26 01:17] upgraded lib32-libtiff (3.9.4-3 -> 3.9.5-1)
[2011-12-26 01:17] upgraded lib32-libxfixes (4.0.5-3 -> 5.0-1)
[2011-12-26 01:17] upgraded lib32-libxcursor (1.1.11-1 -> 1.1.12-1)
[2011-12-26 01:17] upgraded lib32-libxext (1.2.0-1 -> 1.3.0-1)
[2011-12-26 01:17] upgraded lib32-libxi (1.4.1-1 -> 1.4.5-1)
[2011-12-26 01:17] upgraded lib32-libxrandr (1.3.1-1 -> 1.3.2-1)
[2011-12-26 01:17] upgraded lib32-mesa (7.11.2-1 -> 7.11.2-2)
[2011-12-26 01:17] upgraded pcre (8.20-1 -> 8.21-1)
[2011-12-26 01:17] upgraded lib32-pcre (8.20-1 -> 8.21-1)
[2011-12-26 01:17] upgraded lib32-util-linux (2.19-1 -> 2.20.1-1)
[2011-12-26 01:17] upgraded libdvdnav (4.2.0-1 -> 4.2.0-2)
[2011-12-26 01:18] upgraded libmtp (1.1.0-1 -> 1.1.1-1)
[2011-12-26 01:18] upgraded liboauth (0.9.4-2 -> 0.9.6-1)
[2011-12-26 01:18] upgraded libpurple (2.10.0-3 -> 2.10.1-1)
[2011-12-26 01:18] upgraded redland (1:1.0.15-1 -> 1:1.0.15-2)
[2011-12-26 01:18] upgraded libreoffice-common (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-base (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-calc (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-draw (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-extension-ct2n (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-extension-diagram (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-extension-google-docs (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-extension-hunart (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-extension-nlpsolver (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-extension-numbertext (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-extension-oooblogger (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded poppler (0.18.1-1 -> 0.18.2-1)
[2011-12-26 01:18] upgraded libreoffice-extension-pdfimport (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-extension-presentation-minimizer (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-extension-presenter-screen (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-extension-report-builder (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-extension-scripting-beanshell (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-extension-scripting-javascript (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-extension-scripting-python (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-extension-typo (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-extension-validator (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-extension-watch-window (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-extension-wiki-publisher (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-gnome (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-impress (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-kde4 (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-math (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-sdk (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-sdk-doc (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libreoffice-writer (3.4.4-3 -> 3.4.4-4)
[2011-12-26 01:18] upgraded libtracker-sparql (0.12.8-1 -> 0.12.9-1)
[2011-12-26 01:18] upgraded xfconf (4.8.0-2 -> 4.8.1-1)
[2011-12-26 01:18] upgraded libxfce4ui (4.8.0-3 -> 4.8.1-1)
[2011-12-26 01:18] >>> Updating module dependencies. Please wait ...
[2011-12-26 01:18] >>> Generating initial ramdisk, using mkinitcpio.  Please wait...
[2011-12-26 01:18] ==> Building image from preset: 'default'
[2011-12-26 01:18]   -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux.img
[2011-12-26 01:18] ==> Starting build: 3.1.5-1-ARCH
[2011-12-26 01:18]   -> Parsing hook: [base]
[2011-12-26 01:18]   -> Parsing hook: [udev]
[2011-12-26 01:18]   -> Parsing hook: [autodetect]
[2011-12-26 01:18] WARNING: All config files need .conf: /etc/modprobe.d/modprobe.conf.pacnew, it will be ignored in a future release.
[2011-12-26 01:18]   -> Parsing hook: [pata]
[2011-12-26 01:18]   -> Parsing hook: [scsi]
[2011-12-26 01:18]   -> Parsing hook: [sata]
[2011-12-26 01:18]   -> Parsing hook: [filesystems]
[2011-12-26 01:18]   -> Parsing hook: [usbinput]
[2011-12-26 01:18] ==> Generating module dependencies
[2011-12-26 01:18] ==> Creating gzip initcpio image: /boot/initramfs-linux.img
[2011-12-26 01:18] ==> Image generation successful
[2011-12-26 01:18] ==> Building image from preset: 'fallback'
[2011-12-26 01:18]   -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux-fallback.img -S autodetect
[2011-12-26 01:18] ==> Starting build: 3.1.5-1-ARCH
[2011-12-26 01:18]   -> Parsing hook: [base]
[2011-12-26 01:18]   -> Parsing hook: [udev]
[2011-12-26 01:18]   -> Parsing hook: [pata]
[2011-12-26 01:18]   -> Parsing hook: [scsi]
[2011-12-26 01:18]   -> Parsing hook: [sata]
[2011-12-26 01:18]   -> Parsing hook: [filesystems]
[2011-12-26 01:18]   -> Parsing hook: [usbinput]
[2011-12-26 01:18] ==> Generating module dependencies
[2011-12-26 01:18] ==> Creating gzip initcpio image: /boot/initramfs-linux-fallback.img
[2011-12-26 01:18] ==> Image generation successful
[2011-12-26 01:18] upgraded linux (3.1.4-1 -> 3.1.5-1)
[2011-12-26 01:18] installed libbluray (0.2.1-1)
[2011-12-26 01:18] upgraded mplayer (34344-1 -> 34426-1)
[2011-12-26 01:18] upgraded poppler-glib (0.18.1-1 -> 0.18.2-1)
[2011-12-26 01:18] upgraded pygobject-devel (3.0.2-1 -> 3.0.3-1)
[2011-12-26 01:18] upgraded python2-gobject (3.0.2-1 -> 3.0.3-1)
[2011-12-26 01:18] upgraded redland-storage-virtuoso (1:1.0.15-1 -> 1:1.0.15-2)
[2011-12-26 01:18] upgraded ristretto (0.2.3-1 -> 0.3.0-1)
[2011-12-26 01:18] upgraded seahorse (3.2.2-1 -> 3.2.2-2)
[2011-12-26 01:18] upgraded subversion (1.6.17-7 -> 1.7.2-1)
[...]
[2011-12-26 01:22] upgraded texlive-science (2011.22994-1 -> 2011.24724-1)
[2011-12-26 01:22] -> You can now set custom file descriptor ulimits for Tor in
[2011-12-26 01:22] -> "/etc/conf.d/tor" using the "TOR_MAX_FD" variable.
[2011-12-26 01:22] upgraded tor (0.2.2.34-1 -> 0.2.2.35-1)
[2011-12-26 01:22] upgraded vlc (1.1.12-5 -> 1.1.13-1)
[2011-12-26 01:22] upgraded wine (1.3.34-1 -> 1.3.35-3)
[2011-12-26 01:22] upgraded wxgtk (2.8.12.1-1 -> 2.8.12.1-2)
[2011-12-26 01:22] upgraded xfwm4 (4.8.2-1 -> 4.8.3-1)
[2011-12-26 01:22] upgraded xorg-server-common (1.11.2-2 -> 1.11.3-1)
[2011-12-26 01:22] upgraded xorg-server (1.11.2-2 -> 1.11.3-1)
[2011-12-26 01:22] installed inetutils (1.8-6)
[2011-12-26 01:22] upgraded xorg-xinit (1.3.1-1 -> 1.3.1-2)
[2011-12-26 01:22] upgraded yajl (2.0.2-2 -> 2.0.4-1)

Si j'avais un quelconque message d'erreur quelque part je pourrai chercher un peu, mais là, je vois juste que ça ne se connecte pas... Si vous avez des pistes je vous remercie d'avance.

[FoolEcho]

J'ai tenté de me connecté manuelle

iwconfig ne fait pas de connexion, il configure c'est tout.
dhcpcd wlan0 (pour du DHCP, sinon il faut jouer avec ip pour une adresse fixe) pour tenter de récupérer une adresse IP (éventuellement avec -d pour voir le debug).

[benjarobin]

2 remarques mais qui ne vont pas résoudre ton problème (désolé) :
- Remplace ta ligne par

Code : Tout sélectionner

DAEMONS=(hwclock syslog-ng dbus networkmanager @ivman @crond @cupsd)

Car hal ne devrait plus être utilisé ni installé !
Car ifplugd est redondant avec networkmanager

- Utilisé une clé WEP aujourd'hui est presque de l’inconscience... Utilise du WPA... Tant qu'a faire renomme aussi le ESSID en autre chose que "Freebox"

Une piste mais bien mince test avec d'autre canaux wifi
Sinon essaye de remplacer networkmanager par wicd
Et donne nous ce qui s'affiche dans /var/log/everythings.log quand tu essaye de te connecter

[FoolEcho]

Tant qu'on y est, le service cups est cups[b]d[/b] (erreur de recopie, vu que je ne connais pas la commande lispci ? ).

[JPEC]

C'est la mise à jour du kernel qui pose problème… En revenant sur le 3.1.4 je peux me connecter en wifi alors qu'avec le 3.1.5 c'est impossible !

[silmaa]

@benjarobin : merci pour ces corrections, c'est fait ! Sinon pour la clé WEP, c'est vrai que c'est pas hyper safe mais j'habite à la campagne, mon wifi est peut-être accessible à mon plus proche voisin... qui doit avoisiner les 85 ans, donc ça ne risque pas grand chose.

Voici le /var/log/everything.log :

Code : Tout sélectionner

###### iwconfig wlan0 mode managed channel 11 key 1456913A40 essid Freebox
kernel: [  251.053264] cfg80211: Calling CRDA to update world regulatory domain
kernel: [  299.370120] wlan0: authenticate with 4a:5b:8d:f3:5d:88 (try 1)
kernel: [  299.372563] wlan0: authenticated
kernel: [  299.372819] wlan0: associate with 4a:5b:8d:f3:5d:88 (try 1)
kernel: [  299.376527] wlan0: RX AssocResp from 4a:5b:8d:f3:5d:88 (capab=0x411 status=0 aid=4)
kernel: [  299.376531] wlan0: associated
kernel: [  299.441155] wlan0: disassociating from 4a:5b:8d:f3:5d:88 by local choice (reason=3)
kernel: [  299.459950] wlan0: deauthenticating from 4a:5b:8d:f3:5d:88 by local choice (reason=3)
kernel: [  299.574317] cfg80211: Calling CRDA to update world regulatory domain
###### dhcpd wlan0 
dhcpcd[1318]: version 5.2.12 starting
dhcpcd[1318]: wlan0: waiting for carrier
dhcpcd[1318]: timed out
###### le temps que je réponde, network manager a aussi essayé de se connecter, et il est moins avare de détails :
NetworkManager[757]: <info> Auto-activating connection 'Auto Freebox'.
NetworkManager[757]: <info> Activation (wlan0) starting connection 'Auto Freebox'
NetworkManager[757]: <info> (wlan0): device state change: disconnected -> prepare (reason 'none') [30 40 0]
NetworkManager[757]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
NetworkManager[757]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
NetworkManager[757]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
NetworkManager[757]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
NetworkManager[757]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
NetworkManager[757]: <info> (wlan0): device state change: prepare -> config (reason 'none') [40 50 0]
NetworkManager[757]: <info> Activation (wlan0/wireless): access point 'Auto Freebox' has security, but secrets are required.
NetworkManager[757]: <info> (wlan0): device state change: config -> need-auth (reason 'none') [50 60 0]
NetworkManager[757]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
NetworkManager[757]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
NetworkManager[757]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
NetworkManager[757]: <info> (wlan0): device state change: need-auth -> prepare (reason 'none') [60 40 0]
NetworkManager[757]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
NetworkManager[757]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
NetworkManager[757]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
NetworkManager[757]: <info> (wlan0): device state change: prepare -> config (reason 'none') [40 50 0]
NetworkManager[757]: <info> Activation (wlan0/wireless): connection 'Auto Freebox' has security, and secrets exist.  No new secrets needed.
NetworkManager[757]: <info> Config: added 'ssid' value 'Freebox'
NetworkManager[757]: <info> Config: added 'scan_ssid' value '1'
NetworkManager[757]: <info> Config: added 'key_mgmt' value 'NONE'
NetworkManager[757]: <info> Config: added 'auth_alg' value 'OPEN'
NetworkManager[757]: <info> Config: added 'wep_key0' value '<omitted>'
NetworkManager[757]: <info> Config: added 'wep_tx_keyidx' value '0'
NetworkManager[757]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
NetworkManager[757]: <info> Config: set interface ap_scan to 1
NetworkManager[757]: <info> (wlan0): supplicant interface state: disconnected -> scanning
NetworkManager[757]: <info> (wlan0): supplicant interface state: scanning -> authenticating
kernel: [  580.352227] wlan0: authenticate with 4a:5b:8d:f3:5d:88 (try 1)
kernel: [  580.354544] wlan0: authenticated
kernel: [  580.354800] wlan0: associate with 4a:5b:8d:f3:5d:88 (try 1)
NetworkManager[757]: <info> (wlan0): supplicant interface state: authenticating -> associating
kernel: [  580.363610] wlan0: RX ReassocResp from 4a:5b:8d:f3:5d:88 (capab=0x411 status=0 aid=4)
kernel: [  580.363620] wlan0: associated
NetworkManager[757]: <info> (wlan0): supplicant interface state: associating -> completed
NetworkManager[757]: <info> Activation (wlan0/wireless) Stage 2 of 5 (Device Configure) successful.  Connected to wireless network 'Freebox'.
NetworkManager[757]: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) scheduled.
NetworkManager[757]: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) started...
NetworkManager[757]: <info> (wlan0): device state change: config -> ip-config (reason 'none') [50 70 0]
NetworkManager[757]: <info> Activation (wlan0) Beginning DHCPv4 transaction (timeout in 45 seconds)
NetworkManager[757]: <info> dhcpcd started with pid 1332
NetworkManager[757]: <info> Activation (wlan0) Beginning IP6 addrconf.
NetworkManager[757]: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) complete.
dhcpcd[1332]: version 5.2.12 starting
dhcpcd[1332]: wlan0: broadcasting for a lease
NetworkManager[757]: <info> (wlan0): DHCPv4 state changed nbi -> preinit
kernel: [  590.713824] wlan0: no IPv6 routers present
NetworkManager[757]: <info> (wlan0): IP6 addrconf timed out or failed.
NetworkManager[757]: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Timeout) scheduled...
NetworkManager[757]: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Timeout) started...
NetworkManager[757]: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Timeout) complete.
dhcpcd[1332]: timed out
NetworkManager[757]: <info> (wlan0): DHCPv4 client pid 1332 exited with status 1
NetworkManager[757]: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Timeout) scheduled...
NetworkManager[757]: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Timeout) started...
NetworkManager[757]: <warn> Activation (wlan0/wireless): could not get IP configuration for connection 'Auto Freebox'.
NetworkManager[757]: <info> (wlan0): device state change: ip-config -> need-auth (reason 'none') [70 60 0]
NetworkManager[757]: <info> Activation (wlan0/wireless): asking for new secrets
NetworkManager[757]: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Timeout) complete.
kernel: [  610.379141] wlan0: deauthenticating from 4a:5b:8d:f3:5d:88 by local choice (reason=3)
NetworkManager[757]: <info> (wlan0): supplicant interface state: completed -> disconnected
kernel: [  610.431191] cfg80211: Calling CRDA to update world regulatory domain
NetworkManager[757]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
NetworkManager[757]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
NetworkManager[757]: <info> (wlan0): device state change: need-auth -> prepare (reason 'none') [60 40 0]
NetworkManager[757]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
NetworkManager[757]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
NetworkManager[757]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
NetworkManager[757]: <info> (wlan0): device state change: prepare -> config (reason 'none') [40 50 0]
NetworkManager[757]: <info> Activation (wlan0/wireless): connection 'Auto Freebox' has security, and secrets exist.  No new secrets needed.
NetworkManager[757]: <info> Config: added 'ssid' value 'Freebox'
NetworkManager[757]: <info> Config: added 'scan_ssid' value '1'
NetworkManager[757]: <info> Config: added 'key_mgmt' value 'NONE'
NetworkManager[757]: <info> Config: added 'auth_alg' value 'OPEN'
NetworkManager[757]: <info> Config: added 'wep_key0' value '<omitted>'
NetworkManager[757]: <info> Config: added 'wep_tx_keyidx' value '0'
NetworkManager[757]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
NetworkManager[757]: <info> Config: set interface ap_scan to 1
NetworkManager[757]: <info> (wlan0): supplicant interface state: disconnected -> scanning
NetworkManager[757]: <info> (wlan0): supplicant interface state: scanning -> authenticating
kernel: [  616.621938] wlan0: authenticate with 4a:5b:8d:f3:5d:88 (try 1)
kernel: [  616.624461] wlan0: authenticated
kernel: [  616.624636] wlan0: associate with 4a:5b:8d:f3:5d:88 (try 1)
NetworkManager[757]: <info> (wlan0): supplicant interface state: authenticating -> associating
kernel: [  616.633589] wlan0: RX ReassocResp from 4a:5b:8d:f3:5d:88 (capab=0x411 status=0 aid=4)
kernel: [  616.633595] wlan0: associated
NetworkManager[757]: <info> (wlan0): supplicant interface state: associating -> completed
NetworkManager[757]: <info> Activation (wlan0/wireless) Stage 2 of 5 (Device Configure) successful.  Connected to wireless network 'Freebox'.
NetworkManager[757]: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) scheduled.
NetworkManager[757]: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) started...
NetworkManager[757]: <info> (wlan0): device state change: config -> ip-config (reason 'none') [50 70 0]
NetworkManager[757]: (nm-device.c:1540):dhcp4_start: runtime check failed: (priv->dhcp4_client == NULL)
NetworkManager[757]: <info> Activation (wlan0) Beginning DHCPv4 transaction (timeout in 45 seconds)
NetworkManager[757]: <info> dhcpcd started with pid 1337
NetworkManager[757]: <info> Activation (wlan0) Beginning IP6 addrconf.
NetworkManager[757]: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) complete.
dhcpcd[1337]: version 5.2.12 starting
dhcpcd[1337]: wlan0: broadcasting for a lease
NetworkManager[757]: <info> (wlan0): DHCPv4 state changed nbi -> preinit
kernel: [  627.059681] wlan0: no IPv6 routers present
NetworkManager[757]: <info> (wlan0): IP6 addrconf timed out or failed.
NetworkManager[757]: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Timeout) scheduled...
NetworkManager[757]: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Timeout) started...
NetworkManager[757]: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Timeout) complete.
dhcpcd[1337]: timed out
NetworkManager[757]: <info> (wlan0): DHCPv4 client pid 1337 exited with status 1
NetworkManager[757]: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Timeout) scheduled...
NetworkManager[757]: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Timeout) started...
NetworkManager[757]: <warn> Activation (wlan0/wireless): could not get IP configuration for connection 'Auto Freebox'.
NetworkManager[757]: <info> (wlan0): device state change: ip-config -> need-auth (reason 'none') [70 60 0]
NetworkManager[757]: <info> Activation (wlan0/wireless): asking for new secrets
NetworkManager[757]: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Timeout) complete.
kernel: [  646.810687] wlan0: deauthenticating from 4a:5b:8d:f3:5d:88 by local choice (reason=3)
NetworkManager[757]: <info> (wlan0): supplicant interface state: completed -> disconnected
kernel: [  646.866959] cfg80211: Calling CRDA to update world regulatory domain
NetworkManager[757]: get_secret_flags: assertion `is_secret_prop (setting, secret_name, error)' failed
NetworkManager[757]: get_secret_flags: assertion `is_secret_prop (setting, secret_name, error)' failed
NetworkManager[757]: get_secret_flags: assertion `is_secret_prop (setting, secret_name, error)' failed
NetworkManager[757]: get_secret_flags: assertion `is_secret_prop (setting, secret_name, error)' failed
NetworkManager[757]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
NetworkManager[757]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
NetworkManager[757]: <info> (wlan0): device state change: need-auth -> prepare (reason 'none') [60 40 0]
NetworkManager[757]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
NetworkManager[757]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
NetworkManager[757]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
NetworkManager[757]: <info> (wlan0): device state change: prepare -> config (reason 'none') [40 50 0]
NetworkManager[757]: <info> Activation (wlan0/wireless): connection 'Auto Freebox' has security, and secrets exist.  No new secrets needed.
NetworkManager[757]: <info> Config: added 'ssid' value 'Freebox'
NetworkManager[757]: <info> Config: added 'scan_ssid' value '1'
NetworkManager[757]: <info> Config: added 'key_mgmt' value 'NONE'
NetworkManager[757]: <info> Config: added 'auth_alg' value 'OPEN'
NetworkManager[757]: <info> Config: added 'wep_key0' value '<omitted>'
NetworkManager[757]: <info> Config: added 'wep_tx_keyidx' value '0'
NetworkManager[757]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
NetworkManager[757]: <info> Config: set interface ap_scan to 1
NetworkManager[757]: <info> (wlan0): supplicant interface state: disconnected -> scanning
NetworkManager[757]: <info> (wlan0): supplicant interface state: scanning -> authenticating
kernel: [  784.076687] wlan0: authenticate with 4a:5b:8d:f3:5d:88 (try 1)
kernel: [  784.079287] wlan0: authenticated
kernel: [  784.079516] wlan0: associate with 4a:5b:8d:f3:5d:88 (try 1)
NetworkManager[757]: <info> (wlan0): supplicant interface state: authenticating -> associating
kernel: [  784.088239] wlan0: RX ReassocResp from 4a:5b:8d:f3:5d:88 (capab=0x411 status=0 aid=4)
kernel: [  784.088246] wlan0: associated
NetworkManager[757]: <info> (wlan0): supplicant interface state: associating -> completed
NetworkManager[757]: <info> Activation (wlan0/wireless) Stage 2 of 5 (Device Configure) successful.  Connected to wireless network 'Freebox'.
NetworkManager[757]: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) scheduled.
NetworkManager[757]: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) started...
NetworkManager[757]: <info> (wlan0): device state change: config -> ip-config (reason 'none') [50 70 0]
NetworkManager[757]: (nm-device.c:1540):dhcp4_start: runtime check failed: (priv->dhcp4_client == NULL)
NetworkManager[757]: <info> Activation (wlan0) Beginning DHCPv4 transaction (timeout in 45 seconds)
NetworkManager[757]: <info> dhcpcd started with pid 1345
NetworkManager[757]: <info> Activation (wlan0) Beginning IP6 addrconf.
NetworkManager[757]: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) complete.
dhcpcd[1345]: version 5.2.12 starting
dhcpcd[1345]: wlan0: broadcasting for a lease
NetworkManager[757]: <info> (wlan0): DHCPv4 state changed nbi -> preinit
kernel: [  794.410411] wlan0: no IPv6 routers present
NetworkManager[757]: <info> (wlan0): IP6 addrconf timed out or failed.
NetworkManager[757]: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Timeout) scheduled...
NetworkManager[757]: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Timeout) started...
NetworkManager[757]: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Timeout) complete.
dhcpcd[1345]: timed out
NetworkManager[757]: <info> (wlan0): DHCPv4 client pid 1345 exited with status 1
NetworkManager[757]: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Timeout) scheduled...
NetworkManager[757]: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Timeout) started...
NetworkManager[757]: <warn> Activation (wlan0/wireless): could not get IP configuration for connection 'Auto Freebox'.
NetworkManager[757]: <info> (wlan0): device state change: ip-config -> need-auth (reason 'none') [70 60 0]
NetworkManager[757]: <info> Activation (wlan0/wireless): asking for new secrets
NetworkManager[757]: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Timeout) complete.
kernel: [  814.101839] wlan0: deauthenticating from 4a:5b:8d:f3:5d:88 by local choice (reason=3)
NetworkManager[757]: <info> (wlan0): supplicant interface state: completed -> disconnected
kernel: [  814.177733] cfg80211: Calling CRDA to update world regulatory domain
######### Il bloque toujours hyper longtemps sur cette dernière ligne.

@JPEC : oui mais le noyau n'a pas été mis a jour (cf le log que j'ai posté), du moins il me semble... Sinon comment je fais pour revenir à une ancienne version ???

Merci pour vos réponses en tout cas !

edit : orthographe

[JPEC]

Si tu es en version 3.1.5 « upgraded linux (3.1.4-1 -> 3.1.5-1) ».

Downgrader si tu n'as pas pas vidé le cache de pacman :
sudo pacman -U /var/cache/pacman/pkg/linux-3.1.4* (je suis au boulot donc j'ai pas le chemin exact)
et (si tu as les headers d'installés)
sudo pacman -U /var/cache/pacman/pkg/linux-headers-3.1.4* (je suis au boulot donc j'ai pas le chemin exact)

[silmaa]

J'ai :
linux-3.4.1-1-x86_64.pkg.tar.xz
et linux-api-headers-3.4.1-1-x86_64.pkg.tar.xz

Je fais donc

Code : Tout sélectionner

sudo pacman -U /var/cache/pacman/pkg/linux-3.4.1-1-x86_64.pkg.tar.xz
sudo pacman -U /var/cache/pacman/pkg/linux-api-headers-3.4.1-1-x86_64.pkg.tar.xz

? (je préfère être sûr )

[JPEC]

Oui.
L'option -U permet d'installer un pkg local et non sur le dépôt.
Chez moi ça suffit à résoudre les problèmes de wifi avec une carte Intel 5100.

[benjarobin]

@silmaa Tu me prête ta delorean ? On utilise actuellement la version 3.1.5-1 et JPEC te propose d'essayer la version 3.1.4-1
Donc la commande est : pacman -U /var/cache/pacman/pkg/linux-3.1.4-1-x86_64.pkg.tar.xz /var/cache/pacman/pkg/ linux-headers-3.1.4-1-x86_64.pkg.tar.xz

[silmaa]

YEAAAAAAH !!!!!!! Merci beaucoup à tous, en particulier JPEC ! En revanche il faudra refaire la manip à chaque fois que je fais pacman -Syu (une fois par mois en moyenne)?

@benjarobin : je suis fort déçu de n'avoir pas compris la blague

[benjarobin]

Tu avais apparemment la version 3.4 du kernel linux dans ton cache, donc tu devait utiliser ta delorean pour l'avoir (Retour vers le future le film...)

[JPEC]

YEAAAAAAH !!!!!!! Merci beaucoup à tous, en particulier JPEC ! En revanche il faudra refaire la manip à chaque fois que je fais pacman -Syu (une fois par mois en moyenne)?

@benjarobin : je suis fort déçu de n'avoir pas compris la blague

Non lors du pacman -Syu en appuyant sur m tu peux commenter avec « # » les paquets à ne pas mettre à jour (tant que l'on sera pas en linux 3.2) !

[benjarobin]

Tu confond avec yaourt, mais le mieux c'est de lire le man de pacman qui propose une solution à ceci --ignore

[JPEC]

Oui en fait j'utilise tout le temps yaourt !

[silmaa]

Tu confond avec yaourt, mais le mieux c'est de lire le man de pacman qui propose une solution à ceci --ignore

Merci pour l'astuce

Tu avais apparemment la version 3.4 du kernel linux dans ton cache, donc tu devait utiliser ta delorean pour l'avoir (Retour vers le future le film...)

Wah, je devais avoir 6ans la dernière fois que j'ai vu ce film

[FoolEcho]

Ceci dit Marty, tu devrais faire un retour vers le futur en installant le kernel 3.1.6 de [testing] voir si ça corrige ton problème... ou attendre qu'il passe dans [core] si tu cales.

[silmaa]

Re ! Ça me dit bien de tenter le coup.
J'ai ajouté les dépots dans /etc/rc.conf, mais pacman ne veut pas faire la MAJ car il y a la version 4 de pacman dans testing :

Code : Tout sélectionner

:: Les paquets suivants devraient être mis à jour en premier :
    pacman
:: Voulez-vous annuler l'opération courante et
:: mettre à jour ces paquets maintenant ? [O/n] o

résolution des dépendances...
recherche des conflits entre paquets...
Erreur: la préparation de la transaction a échoué (la satisfaction des dépendances a échoué)
:: package-query: requiert pacman<3.6

J'ai trouvé une réponse ici (mais ça concerne le passage à pacman 3.5) : http://forums.archlinux.fr/topic7810.html. J'ai donc fait la manip, mais sans succès... Voici le log avec --debug :

Code : Tout sélectionner

[...]
debug: config: new section 'testing'
debug: registering sync database 'testing'
debug: config file /etc/pacman.conf, line 63: including /etc/pacman.d/mirrorlist
debug: config: attempting to read file /etc/pacman.d/mirrorlist
debug: adding new server URL to database 'testing': http://mir.archlinux.fr/testing/os/x86_64
debug: adding new server URL to database 'testing': ftp://archlinux.mirrors.ovh.net/archlinux/testing/os/x86_64
debug: adding new server URL to database 'testing': ftp://mir1.archlinux.fr/archlinux/testing/os/x86_64
[la meme chose pour 'core' 'extra' 'community-testing' 'community' 'multilib' et 'archlinuxfr' (sauf que pour archlinuxfr j'ai debug: adding new server URL to database 'archlinuxfr': http://repo.archlinux.fr/x86_64 au lieu de http://mir.archlinux.fr/$repo/os/x86_64]
:: Synchronisation des bases de données de paquets...
debug: database path for tree local set to /var/lib/pacman/local/
debug: local database version 2
debug: no file found matching criteria, starting from scratch
debug: using 'testing.db' for download progress
[...]
debug: ust.mtime: 1325059857 local_time: 0 compare: -1325059857
debug: ust.size: 11550 local_size: 0 compare: -11550
debug: mtimes were different or unavailable, downloading testing.db from beginning
debug: connected to mir.archlinux.fr successfully
téléchargement de testing.db...
debug: no file found matching criteria, starting from scratch
[idem pour les autres dépots, pas de soucis particulier...]
debug: loading package cache for repository 'local'
[s'ensuit une liste gigantesque de "addig 'paquet' to package cache for db 'local', j'ai laissé ceux concernant pacman]
debug: adding 'pacman-mirrorlist' to package cache for db 'local'
debug: adding 'pacman' to package cache for db 'local'
debug: loading package cache for repository 'testing'
debug: database path for tree testing set to /var/lib/pacman/sync/testing.db
debug: opening database archive /var/lib/pacman/sync/testing.db
debug: new version of 'pacman' found (3.5.4-4 => 4.0.1-1)
debug: loading package cache for repository 'core'
debug: database path for tree core set to /var/lib/pacman/sync/core.db
debug: opening database archive /var/lib/pacman/sync/core.db
debug: loading package cache for repository 'extra'
debug: database path for tree extra set to /var/lib/pacman/sync/extra.db
debug: opening database archive /var/lib/pacman/sync/extra.db
debug: loading package cache for repository 'community-testing'
debug: database path for tree community-testing set to /var/lib/pacman/sync/community-testing.db
debug: opening database archive /var/lib/pacman/sync/community-testing.db
debug: loading package cache for repository 'community'
debug: database path for tree community set to /var/lib/pacman/sync/community.db
debug: opening database archive /var/lib/pacman/sync/community.db
debug: loading package cache for repository 'archlinuxfr'
debug: database path for tree archlinuxfr set to /var/lib/pacman/sync/archlinuxfr.db
debug: opening database archive /var/lib/pacman/sync/archlinuxfr.db
:: Les paquets suivants devraient être mis à jour en premier :
    pacman

debug: local database version 2
debug: adding package 'pacman'
debug: adding package pacman-4.0.1-1 to the transaction targets
résolution des dépendances...
debug: resolving target's dependencies
debug: started resolving dependencies
debug: checkdeps: package pacman-4.0.1-1
debug: finished resolving dependencies
debug: started sorting dependencies
debug: sorting dependencies finished
recherche des conflits entre paquets...
debug: looking for conflicts
debug: check targets vs targets
debug: check targets vs targets
debug: check targets vs db and db vs targets
debug: check targets vs db
debug: check db vs targets
debug: checking dependencies
debug: checkdeps: package pacman-4.0.1-1
debug: checkdeps: transaction would break 'pacman<3.6' dependency of 'package-query'
:: package-query: requiert pacman<3.6
debug: unregistering database 'local'
debug: freeing package cache for repository 'local'
debug: unregistering database 'testing'
debug: freeing package cache for repository 'testing'
debug: unregistering database 'core'
debug: freeing package cache for repository 'core'
debug: unregistering database 'extra'
debug: freeing package cache for repository 'extra'
debug: unregistering database 'community-testing'
debug: freeing package cache for repository 'community-testing'
debug: unregistering database 'community'
debug: freeing package cache for repository 'community'
debug: unregistering database 'archlinuxfr'
debug: freeing package cache for repository 'archlinuxfr'
debug: unregistering database 'multilib'

J'ai dû élaguer car le message n'était pas accepté, car trop long.
Bon si c'est trop compliqué je peux aussi attendre un peu ^^

[FoolEcho]

Tu as juste à activer [testing], lancer la synchronisation (pacman -Sy) et enfin installer le kernel (pacman -S linux). Si pacman te demande à passer en 4.0, tu n'as qu'à répondre non, ça ne devrait pas t'empêcher de mettre le kernel à jour (et si le noyau fonctionne, après redémarrage bien spur, tu pourras enlever [testing] et resynchroniser).

Pour une prochaine fois, il y a pastebin pour les longs logs.

[benjarobin]

C'est comme même plus simple de faire :

Code : Tout sélectionner

pacman -U http://mir.archlinux.fr/testing/os/x86_64/linux-3.1.6-1-x86_64.pkg.tar.xz http://mir.archlinux.fr/testing/os/x86_64/linux-headers-3.1.6-1-x86_64.pkg.tar.xz