Je suis nouveau sur ArchLinux, j'ai migré depuis Fedora 10, que j'aime beaucoup, mais qui selon mois, ne supporte pas assez bien KDE. Tout fonctionne a peu près, même ma Creative X-Fi! J'ai par contre des soucis avec ma carte graphique. L'activation du pilote "radeon" m'empêche de lire des vidéos. En effet, dès que j'agrandis la video avec mplayer, ça saccade et devient inregardable. VLC me lance même une fête séparée avec affichage X11, super saccadé.
Comment puis-je activer l'overlay dans les pilotes libre (Merci AMD
).Code : Tout sélectionner
Linux version 2.6.29-ARCH (root@T-POWA-LX) (gcc version 4.4.0 (GCC) ) #1 SMP PREEMPT Wed May 20 06:42:43 UTC 2009
Command line: root=/dev/disk/by-uuid/61a8c7b9-52be-4e75-8735-f445e048a55a ro vga=795 nomodeset
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000bffb0000 (usable)
BIOS-e820: 00000000bffb0000 - 00000000bffbe000 (ACPI data)
BIOS-e820: 00000000bffbe000 - 00000000bffe0000 (ACPI NVS)
BIOS-e820: 00000000bffe0000 - 00000000c0000000 (reserved)
BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
DMI 2.3 present.
AMI BIOS detected: BIOS may corrupt low RAM, working around it.
last_pfn = 0xbffb0 max_arch_pfn = 0x100000000
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Scanning 0 areas for low memory corruption
modified physical RAM map:
modified: 0000000000000000 - 0000000000010000 (reserved)
modified: 0000000000010000 - 000000000009fc00 (usable)
modified: 000000000009fc00 - 00000000000a0000 (reserved)
modified: 00000000000e0000 - 0000000000100000 (reserved)
modified: 0000000000100000 - 00000000bffb0000 (usable)
modified: 00000000bffb0000 - 00000000bffbe000 (ACPI data)
modified: 00000000bffbe000 - 00000000bffe0000 (ACPI NVS)
modified: 00000000bffe0000 - 00000000c0000000 (reserved)
modified: 00000000ff780000 - 0000000100000000 (reserved)
init_memory_mapping: 0000000000000000-00000000bffb0000
0000000000 - 00bfe00000 page 2M
00bfe00000 - 00bffb0000 page 4k
kernel direct mapping tables up to bffb0000 @ 10000-15000
last_map_addr: bffb0000 end: bffb0000
RAMDISK: 37f36000 - 37fef1cd
ACPI: RSDP 000FB1E0, 0014 (r0 ACPIAM)
ACPI: RSDT BFFB0000, 0034 (r1 A_M_I_ OEMRSDT 12000809 MSFT 97)
ACPI: FACP BFFB0200, 0084 (r2 A_M_I_ OEMFACP 12000809 MSFT 97)
FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4)
ACPI: DSDT BFFB0430, 5ADB (r1 A0387 A0387001 1 INTL 2002026)
ACPI: FACS BFFBE000, 0040
ACPI: APIC BFFB0390, 005C (r1 A_M_I_ OEMAPIC 12000809 MSFT 97)
ACPI: MCFG BFFB03F0, 003C (r1 A_M_I_ OEMMCFG 12000809 MSFT 97)
ACPI: OEMB BFFBE040, 006B (r1 A_M_I_ AMI_OEM 12000809 MSFT 97)
ACPI: Local APIC address 0xfee00000
(6 early reservations) ==> bootmem [0000000000 - 00bffb0000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#2 [0000200000 - 000076fb50] TEXT DATA BSS ==> [0000200000 - 000076fb50]
#3 [0037f36000 - 0037fef1cd] RAMDISK ==> [0037f36000 - 0037fef1cd]
#4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
#5 [0000010000 - 0000013000] PGTABLE ==> [0000010000 - 0000013000]
found SMP MP-table at [ffff8800000ff780] 000ff780
[ffffe20000000000-ffffe200029fffff] PMD -> [ffff880001200000-ffff880003bfffff] on node 0
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x00100000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x000bffb0
On node 0 totalpages: 786239
DMA zone: 56 pages used for memmap
DMA zone: 1495 pages reserved
DMA zone: 2432 pages, LIFO batch:0
DMA32 zone: 10695 pages used for memmap
DMA32 zone: 771561 pages, LIFO batch:31
Detected use of extended apic ids on hypertransport bus
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at c4000000 (gap: c0000000:3f780000)
NR_CPUS:16 nr_cpumask_bits:16 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Allocating 53248 bytes of per cpu data
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 773993
Kernel command line: root=/dev/disk/by-uuid/61a8c7b9-52be-4e75-8735-f445e048a55a ro vga=795 nomodeset
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Fast TSC calibration using PIT
Detected 2004.957 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Checking aperture...
No AGP bridge found
Node 0: aperture @ 30a0000000 size 32 MB
Aperture beyond 4GB. Ignoring.
Memory: 3088476k/3145408k available (2783k kernel code, 452k absent, 55764k reserved, 1209k data, 380k init)
SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Calibrating delay loop (skipped), value calculated using timer frequency.. 4011.99 BogoMIPS (lpj=6683190)
Security Framework initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
tseg: 0000000000
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
ACPI: Core revision 20081204
ACPI: Checking initramfs for custom DSDT
Setting APIC routing to flat
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 01
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4010.85 BogoMIPS (lpj=6681373)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 01
Brought up 2 CPUs
Total of 2 processors activated (8021.85 BogoMIPS).
net_namespace: 1824 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
node 0 link 0: io port [1000, ffffff]
TOM: 00000000c0000000 aka 3072M
node 0 link 0: mmio [e0000000, efffffff]
node 0 link 0: mmio [c0000000, dfffffff]
node 0 link 0: mmio [a0000, bffff]
node 0 link 0: mmio [c0000000, ffffffff]
bus: [00,ff] on node 0 link 0
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [c0000000, fcffffffff]
bus: 00 index 2 mmio: [a0000, bffff]
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: Not using MMCONFIG.
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
PCI: Using MMCONFIG at e0000000 - efffffff
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:1c.0: reg 10 32bit mmio: [0xc5efc000-0xc5efcfff]
pci 0000:00:1c.1: reg 10 32bit mmio: [0xc5efd000-0xc5efdfff]
pci 0000:00:1c.2: reg 10 32bit mmio: [0xc5efe000-0xc5efefff]
pci 0000:00:1c.3: reg 10 32bit mmio: [0xc5effc00-0xc5effcff]
pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.3: PME# disabled
pci 0000:00:1e.1: quirk: region 4000-403f claimed by ali7101 ACPI
pci 0000:00:1f.0: reg 20 io port: [0xff00-0xff0f]
pci 0000:00:1f.1: reg 10 io port: [0xc800-0xc807]
pci 0000:00:1f.1: reg 14 io port: [0xc400-0xc403]
pci 0000:00:1f.1: reg 18 io port: [0xc000-0xc007]
pci 0000:00:1f.1: reg 1c io port: [0xb800-0xb803]
pci 0000:00:1f.1: reg 20 io port: [0xb400-0xb40f]
pci 0000:00:1f.1: reg 24 32bit mmio: [0xc5eff800-0xc5effbff]
pci 0000:00:1f.1: PME# supported from D3hot
pci 0000:00:1f.1: PME# disabled
pci 0000:01:00.0: reg 10 64bit mmio: [0xd0000000-0xdfffffff]
pci 0000:01:00.0: reg 18 64bit mmio: [0xc5fe0000-0xc5feffff]
pci 0000:01:00.0: reg 20 io port: [0xd000-0xd0ff]
pci 0000:01:00.0: reg 30 32bit mmio: [0xc5fc0000-0xc5fdffff]
pci 0000:01:00.0: supports D1 D2
pci 0000:01:00.1: reg 10 64bit mmio: [0xc5ff0000-0xc5ffffff]
pci 0000:01:00.1: supports D1 D2
pci 0000:00:02.0: bridge io port: [0xd000-0xdfff]
pci 0000:00:02.0: bridge 32bit mmio: [0xc5f00000-0xc5ffffff]
pci 0000:00:02.0: bridge 32bit mmio pref: [0xd0000000-0xdfffffff]
pci 0000:02:11.0: reg 10 io port: [0xe800-0xe81f]
pci 0000:02:11.0: reg 14 64bit mmio: [0xcee00000-0xceffffff]
pci 0000:02:11.0: reg 1c 64bit mmio: [0xc8000000-0xcbffffff]
pci 0000:02:11.0: supports D1 D2
pci 0000:02:12.0: reg 10 32bit mmio: [0xc6000000-0xc6ffffff]
pci 0000:02:12.1: reg 10 32bit mmio: [0xc7000000-0xc7ffffff]
pci 0000:02:12.2: reg 10 32bit mmio: [0xcc000000-0xccffffff]
pci 0000:02:12.4: reg 10 32bit mmio: [0xcd000000-0xcdffffff]
pci 0000:02:13.0: reg 10 32bit mmio: [0xcedff800-0xcedfffff]
pci 0000:02:13.0: reg 14 32bit mmio: [0xcedf8000-0xcedfbfff]
pci 0000:02:13.0: supports D1 D2
pci 0000:02:13.0: PME# supported from D0 D1 D2 D3hot
pci 0000:02:13.0: PME# disabled
pci 0000:02:14.0: reg 10 32bit mmio: [0xcedf4000-0xcedf7fff]
pci 0000:02:14.0: reg 14 io port: [0xe400-0xe4ff]
pci 0000:02:14.0: reg 30 32bit mmio: [0xcedc0000-0xceddffff]
pci 0000:02:14.0: supports D1 D2
pci 0000:02:14.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:14.0: PME# disabled
pci 0000:00:1a.0: bridge io port: [0xe000-0xefff]
pci 0000:00:1a.0: bridge 32bit mmio: [0xc6000000-0xceffffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE2P._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 12 14 *15), disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15), disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15), disabled.
ACPI: PCI Interrupt Link [LNKP] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI Warning (tbutils-0242): Incorrect checksum in table [OEMB] - E8, should be BA [20081204]
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 17 devices
ACPI: ACPI bus type pnp unregistered
system 00:09: ioport range 0x28d-0x28e has been reserved
system 00:09: ioport range 0x480-0x48f has been reserved
system 00:09: ioport range 0x4d0-0x4d1 has been reserved
system 00:09: ioport range 0x4000-0x40bf could not be reserved
system 00:09: ioport range 0x40c0-0x40df has been reserved
system 00:09: ioport range 0x900-0x91f has been reserved
system 00:09: iomem range 0xfff80000-0xffffffff has been reserved
system 00:09: iomem range 0xffb00000-0xffbfffff has been reserved
system 00:09: iomem range 0xff6fe000-0xff6fefff has been reserved
system 00:09: iomem range 0xff6ff000-0xff6fffff has been reserved
system 00:09: iomem range 0xff780000-0xff7fffff has been reserved
system 00:0c: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0c: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:0e: ioport range 0xc00-0xc0f has been reserved
system 00:0e: ioport range 0xd00-0xd0f has been reserved
system 00:0e: ioport range 0xa20-0xa2f has been reserved
system 00:0e: ioport range 0xa30-0xa3f has been reserved
system 00:0f: iomem range 0xe0000000-0xefffffff has been reserved
system 00:10: iomem range 0x0-0x9ffff could not be reserved
system 00:10: iomem range 0xc0000-0xcffff has been reserved
system 00:10: iomem range 0xe0000-0xfffff could not be reserved
system 00:10: iomem range 0x100000-0xbfffffff could not be reserved
system 00:10: iomem range 0xfff80000-0xffffffff has been reserved
pci 0000:00:02.0: PCI bridge, secondary bus 0000:01
pci 0000:00:02.0: IO window: 0xd000-0xdfff
pci 0000:00:02.0: MEM window: 0xc5f00000-0xc5ffffff
pci 0000:00:02.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
pci 0000:00:1a.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1a.0: IO window: 0xe000-0xefff
pci 0000:00:1a.0: MEM window: 0xc6000000-0xceffffff
Switched to high resolution mode on CPU 0
pci 0000:00:1a.0: PREFETCH window: disabled
pci 0000:00:02.0: setting latency timer to 64
pci 0000:00:1a.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:01: resource 0 io: [0xd000-0xdfff]
pci_bus 0000:01: resource 1 mem: [0xc5f00000-0xc5ffffff]
pci_bus 0000:01: resource 2 mem: [0xd0000000-0xdfffffff]
pci_bus 0000:01: resource 3 mem: [0x0-0x0]
pci_bus 0000:02: resource 0 io: [0xe000-0xefff]
pci_bus 0000:02: resource 1 mem: [0xc6000000-0xceffffff]
pci_bus 0000:02: resource 2 mem: [0x0-0x0]
pci_bus 0000:02: resource 3 mem: [0x0-0x0]
NET: Registered protocol family 2
Switched to high resolution mode on CPU 1
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs... done
Freeing initrd memory: 740k freed
Scanning for low memory corruption every 60 seconds
audit: initializing netlink socket (disabled)
type=2000 audit(1243289321.326:1): initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
msgmni has been set to 6035
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:00.0: MSI quirk detected; MSI disabled
pci 0000:01:00.0: Boot video device
pcieport-driver 0000:00:02.0: setting latency timer to 64
aer 0000:00:02.0:pcie01: AER service couldn't init device: no _OSC support
vesafb: framebuffer at 0xd0000000, mapped to 0xffffc20010100000, using 10240k, total 16384k
vesafb: mode is 1280x1024x32, linelength=5120, pages=2
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
Console: switching to colour frame buffer device 160x64
fb0: VESA VGA frame buffer device
Linux agpgart interface v0.103
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
input: Macintosh mouse button emulation as /devices/virtual/input/input0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
registered taskstats version 1
Freeing unused kernel memory: 380k freed
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
SCSI subsystem initialized
libata version 3.00 loaded.
pata_ali 0000:00:1f.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
scsi0 : pata_ali
scsi1 : pata_ali
ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14
ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15
ata1.00: ATAPI: HL-DT-ST GCE-8480B, 1.06, max UDMA/33
ata1.00: WARNING: ATAPI DMA disabled for reliablity issues. It can be enabled
ata1.00: WARNING: via pata_ali.atapi_dma modparam or corresponding sysfs node.
ata1.00: configured for UDMA/33
isa bounce pool size: 16 pages
scsi 0:0:0:0: CD-ROM HL-DT-ST CD-RW GCE-8480B 1.06 PQ: 0 ANSI: 5
ata2.00: ATAPI: TSSTcorp CDDVDW SH-S202N, SB02, max UDMA/66
ata2.00: WARNING: ATAPI DMA disabled for reliablity issues. It can be enabled
ata2.00: WARNING: via pata_ali.atapi_dma modparam or corresponding sysfs node.
ata2.00: configured for UDMA/66
scsi 1:0:0:0: CD-ROM TSSTcorp CDDVDW SH-S202N SB02 PQ: 0 ANSI: 5
ahci 0000:00:1f.1: version 3.0
ahci 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.1: AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl IDE mode
ahci 0000:00:1f.1: flags: ncq sntf ilck pm led clo pmp pio slum part
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata3: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 19
ata4: SATA max UDMA/133 irq_stat 0x00400040 irq 19
ata5: SATA max UDMA/133 irq_stat 0x00400040, connection status changed
ata6: SATA max UDMA/133 abar m1024@0xc5eff800 port 0xc5effa80 irq 19
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-7: MAXTOR STM3250820AS, 3.AAE, max UDMA/133
ata3.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata3.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA MAXTOR STM325082 3.AA PQ: 0 ANSI: 5
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATA-7: HDT722525DLA380, V44OA9BA, max UDMA/133
ata4.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata4.00: configured for UDMA/133
scsi 3:0:0:0: Direct-Access ATA HDT722525DLA380 V44O PQ: 0 ANSI: 5
ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata5.00: ATA-7: MAXTOR STM3250310AS, 3.AAC, max UDMA/133
ata5.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata5.00: configured for UDMA/133
scsi 4:0:0:0: Direct-Access ATA MAXTOR STM325031 3.AA PQ: 0 ANSI: 5
ata6: SATA link down (SStatus 0 SControl 300)
Driver 'sd' needs updating - please use bus_type methods
sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
Driver 'sr' needs updating - please use bus_type methods
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
Uniform CD-ROM driver Revision: 3.20
sr 0:0:0:0: Attached scsi CD-ROM sr0
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
sda1
sr 1:0:0:0: Attached scsi CD-ROM sr1
sd 2:0:0:0: [sda] Attached SCSI disk
sd 3:0:0:0: [sdb] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:0:0:0: [sdb] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 3:0:0:0: [sdb] Attached SCSI disk
sd 4:0:0:0: [sdc] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
sd 4:0:0:0: [sdc] Write Protect is off
sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 4:0:0:0: [sdc] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
sd 4:0:0:0: [sdc] Write Protect is off
sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1 sdc2 sdc3 sdc4 < sdc5 sdc6 sdc7 sdc8 sdc9 >
sd 4:0:0:0: [sdc] Attached SCSI disk
EXT4-fs: barriers enabled
EXT4-fs: delayed allocation enabled
kjournald2 starting: pid 658, dev sdc3:8, commit interval 5 seconds
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs: mounted filesystem sdc3 with ordered data mode
rtc_cmos 00:02: RTC can wake from S4
rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, 114 bytes nvram
udev: starting version 141
CTALSA 0000:02:11.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
fuse init (API version 7.11)
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
ACPI: Power Button (CM) [PWRB]
processor ACPI_CPU:00: registered as cooling_device0
ACPI: Processor [CPU1] (supports 8 throttling states)
processor ACPI_CPU:01: registered as cooling_device1
IT8712 SuperIO detected.
parport_pc 00:06: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
sr 0:0:0:0: Attached scsi generic sg0 type 5
sr 1:0:0:0: Attached scsi generic sg1 type 5
sd 2:0:0:0: Attached scsi generic sg2 type 0
sd 3:0:0:0: Attached scsi generic sg3 type 0
sd 4:0:0:0: Attached scsi generic sg4 type 0
gameport: NS558 PnP Gameport is pnp00:07/gameport0, io 0x201, speed 581kHz
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
sr 0:0:0:0: [sr0] Result: hostbyte=0x00 driverbyte=0x08
sr 0:0:0:0: [sr0] Sense Key : 0x5 [current]
sr 0:0:0:0: [sr0] ASC=0x21 ASCQ=0x0
end_request: I/O error, dev sr0, sector 0
Buffer I/O error on device sr0, logical block 0
sr 0:0:0:0: [sr0] Result: hostbyte=0x00 driverbyte=0x08
sr 0:0:0:0: [sr0] Sense Key : 0x5 [current]
sr 0:0:0:0: [sr0] ASC=0x21 ASCQ=0x0
end_request: I/O error, dev sr0, sector 0
Buffer I/O error on device sr0, logical block 0
input: PC Speaker as /devices/platform/pcspkr/input/input4
Linux video capture interface: v2.00
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1c.3: PCI INT D -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1c.3: EHCI Host Controller
ehci_hcd 0000:00:1c.3: new USB bus registered, assigned bus number 1
Error: Driver 'pcspkr' is already registered, aborting...
ehci_hcd 0000:00:1c.3: debug port 1
ehci_hcd 0000:00:1c.3: irq 23, io mem 0xc5effc00
ehci_hcd 0000:00:1c.3: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
skge 0000:02:14.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
skge 1.13 addr 0xcedf4000 irq 21 chip Yukon-Lite rev 9
skge eth0: addr 00:15:f2:d3:c7:13
lp0: using parport0 (interrupt-driven).
ali15x3_smbus 0000:00:1e.1: ALI15X3_smb region uninitialized - upgrade BIOS or use force_addr=0xaddr
ali15x3_smbus 0000:00:1e.1: ALI15X3 not detected, module not inserted.
ali1535_smbus 0000:00:1e.1: ALI1535_smb region uninitialized - upgrade BIOS?
ali1535_smbus 0000:00:1e.1: ALI1535 not detected, module not inserted.
ppdev: user-space parallel port driver
ohci1394 0000:02:13.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
alim7101_wdt: Steve Hill <steve@navaho.co.uk>.
alim7101_wdt: ALi 1543 South-Bridge not present - WDT not set
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=[cedff800-cedfffff] Max Packet=[2048] IR/IT contexts=[4/8]
cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
cx8800 0000:02:12.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
cx88[0]: subsystem: 0070:9402, board: Hauppauge WinTV-HVR1100 DVB-T/Hybrid [card=40,autodetected], frontend(s): 1
cx88[0]: TV tuner type 63, Radio tuner type -1
cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:1c.0: OHCI Host Controller
ohci_hcd 0000:00:1c.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:1c.0: irq 17, io mem 0xc5efc000
usb 1-4: new high speed USB device using ehci_hcd and address 3
cx2388x alsa driver version 0.0.6 loaded
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ohci_hcd 0000:00:1c.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:1c.1: OHCI Host Controller
ohci_hcd 0000:00:1c.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:1c.1: irq 18, io mem 0xc5efd000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
ohci_hcd 0000:00:1c.2: PCI INT C -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:1c.2: OHCI Host Controller
ohci_hcd 0000:00:1c.2: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:1c.2: irq 19, io mem 0xc5efe000
tuner' 0-0043: chip found @ 0x86 (cx88[0])
tda9887 0-0043: creating new instance
tda9887 0-0043: tda988[5/6/7] found
tuner' 0-0061: chip found @ 0xc2 (cx88[0])
tuner' 0-0063: chip found @ 0xc6 (cx88[0])
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 3 ports detected
tveeprom 0-0050: Hauppauge model 94009, rev C2A0, serial# 208333
tveeprom 0-0050: MAC address is 00-0D-FE-03-2D-CD
tveeprom 0-0050: tuner model is Philips FMD1216ME (idx 100, type 63)
tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4)
tveeprom 0-0050: audio processor is CX882 (idx 33)
tveeprom 0-0050: decoder processor is CX882 (idx 25)
tveeprom 0-0050: has radio, has IR receiver, has no IR transmitter
cx88[0]: hauppauge eeprom: model=94009
usb 1-4: configuration #1 chosen from 1 choice
tuner-simple 0-0061: creating new instance
tuner-simple 0-0061: type set to 63 (Philips FMD1216ME MK3 Hybrid Tuner)
input: cx88 IR (Hauppauge WinTV-HVR110 as /devices/pci0000:00/0000:00:1a.0/0000:02:12.0/input/input5
cx88[0]/0: found at 0000:02:12.0, rev: 5, irq: 19, latency: 64, mmio: 0xc6000000
IRQ 19/cx88[0]: IRQF_DISABLED is not guaranteed on shared IRQs
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
cx88[0]/0: registered device radio0
cx88[0]/2: cx2388x 8802 Driver Manager
cx88-mpeg driver manager 0000:02:12.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19
cx88[0]/2: found at 0000:02:12.2, rev: 5, irq: 19, latency: 64, mmio: 0xcc000000
IRQ 19/cx88[0]: IRQF_DISABLED is not guaranteed on shared IRQs
cx88_audio 0000:02:12.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
IRQ 19/cx88[0]: IRQF_DISABLED is not guaranteed on shared IRQs
cx88[0]/1: CX88x/0: ALSA support for cx2388x boards
logips2pp: Detected unknown logitech mouse model 127
cx88/2: cx2388x dvb driver version 0.0.6 loaded
cx88/2: registering cx8802 driver, type: dvb access: shared
cx88[0]/2: subsystem: 0070:9402, board: Hauppauge WinTV-HVR1100 DVB-T/Hybrid [card=40]
cx88[0]/2: cx2388x based DVB/ATSC card
cx8802_alloc_frontends() allocating 1 frontend(s)
usb 1-6: new high speed USB device using ehci_hcd and address 4
gspca: main v2.4.0 registered
gspca: probing 06f8:3003
ov534: sccb status 0x07, attempt 1/5
ov534: sccb_reg_read failed 1
ov534: sccb status 0x07, attempt 1/5
ov534: sccb_reg_read failed 2
ov534: sccb status 0x07, attempt 1/5
ov534: sccb_reg_read failed 1
ov534: sccb status 0x07, attempt 1/5
ov534: sccb_reg_read failed 2
ov534: sensor is ovffff
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
tuner-simple 0-0061: attaching existing instance
tuner-simple 0-0061: type set to 63 (Philips FMD1216ME MK3 Hybrid Tuner)
DVB: registering new adapter (cx88[0])
DVB: registering adapter 0 frontend 2072725714 (Conexant CX22702 DVB-T)...
ov534: sccb status 0x07, attempt 1/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: sccb status 0x07, attempt 1/5
ov534: sccb status 0x07, attempt 2/5
ov534: sccb_reg_write failed
ov534: frame_rate: 30
gspca: probe ok
gspca: probing 06f8:3003
gspca: probing 06f8:3003
usbcore: registered new interface driver ov534
ov534: registered
3:2:1: cannot get freq at ep 0x84
usbcore: registered new interface driver snd-usb-audio
usb 1-6: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi6 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb 2-1: new full speed USB device using ohci_hcd and address 2
input: ImExPS/2 Logitech Explorer Mouse as /devices/platform/i8042/serio1/input/input6
usb 2-1: configuration #1 chosen from 1 choice
Bluetooth: Core ver 2.14
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: Generic Bluetooth USB driver ver 0.4
usbcore: registered new interface driver btusb
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d80000941ccc]
EXT4 FS on sdc3, internal journal on sdc3:8
EXT4-fs: barriers enabled
kjournald2 starting: pid 2281, dev sdc6:8, commit interval 5 seconds
EXT4 FS on sdc6, internal journal on sdc6:8
EXT4-fs: delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs: mounted filesystem sdc6 with ordered data mode
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdc2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
EXT4-fs: barriers enabled
kjournald2 starting: pid 2292, dev sdc8:8, commit interval 5 seconds
EXT4 FS on sdc8, internal journal on sdc8:8
EXT4-fs: delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs: mounted filesystem sdc8 with ordered data mode
EXT4-fs: barriers enabled
kjournald2 starting: pid 2293, dev sdc9:8, commit interval 5 seconds
EXT4 FS on sdc9, internal journal on sdc9:8
EXT4-fs: delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs: mounted filesystem sdc9 with ordered data mode
EXT4-fs: barriers enabled
kjournald2 starting: pid 2294, dev sdc5:8, commit interval 5 seconds
EXT4 FS on sdc5, internal journal on sdc5:8
EXT4-fs: delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs: mounted filesystem sdc5 with ordered data mode
Adding 2996080k swap on /dev/sdc7. Priority:-1 extents:1 across:2996080k
scsi 6:0:0:0: Direct-Access Maxtor 6 L200P0 BAH4 PQ: 0 ANSI: 0
sd 6:0:0:0: [sdd] 398297088 512-byte hardware sectors: (203 GB/189 GiB)
sd 6:0:0:0: [sdd] Write Protect is off
sd 6:0:0:0: [sdd] Mode Sense: 03 00 00 00
sd 6:0:0:0: [sdd] Assuming drive cache: write through
sd 6:0:0:0: [sdd] 398297088 512-byte hardware sectors: (203 GB/189 GiB)
sd 6:0:0:0: [sdd] Write Protect is off
sd 6:0:0:0: [sdd] Mode Sense: 03 00 00 00
sd 6:0:0:0: [sdd] Assuming drive cache: write through
sdd:<6>skge eth0: enabling interface
sdd1
sd 6:0:0:0: [sdd] Attached SCSI disk
sd 6:0:0:0: Attached scsi generic sg5 type 0
usb-storage: device scan complete
skge eth0: Link is up at 100 Mbps, full duplex, flow control both
3:2:1: cannot get freq at ep 0x84
3:2:1: cannot get freq at ep 0x84
Bluetooth: L2CAP ver 2.11
Bluetooth: L2CAP socket layer initialized
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bridge firewalling registered
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.10
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
pci 0000:01:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[drm] Initialized drm 1.1.0 20060810
BUG: unable to handle kernel NULL pointer dereference at 0000000000000282
IP: [<ffffffffa04fab23>] drm_init+0x23/0x220 [drm]
PGD bb6d5067 PUD bb6d4067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:02.0/0000:01:00.0/enable
CPU 1
Modules linked in: radeon(+) drm ipv6 rfcomm sco bridge stp llc bnep l2cap ext3 jbd btusb bluetooth usb_storage snd_usb_audio snd_usb_lib snd_hwdep cx22702 gspca_ov534 gspca_main cx88_dvb cx88_vp3054_i2c videobuf_dvb dvb_core tuner_simple tuner_types tda9887 tda8290 tuner psmouse cx88_alsa ohci_hcd cx8802 cx8800 cx88xx serio_raw ohci1394 analog ir_common ppdev i2c_ali1535 i2c_ali15x3 lp skge ehci_hcd i2c_algo_bit v4l2_common videodev v4l1_compat ieee1394 tveeprom i2c_core pcspkr v4l2_compat_ioctl32 btcx_risc videobuf_dma_sg videobuf_core usbcore shpchp pci_hotplug k8temp sg ns558 snd_mpu401 snd_mpu401_uart gameport snd_rawmidi parport_pc parport thermal processor evdev fan button battery ac fuse snd_seq_oss snd_seq_midi_event snd_seq snd_seq_device snd_pcm_oss snd_mixer_oss ctxfi snd_pcm snd_timer snd soundcore snd_page_alloc rtc_cmos rtc_core rtc_lib ext4 mbcache jbd2 crc16 sr_mod sd_mod cdrom pata_acpi ata_generic ahci pata_ali libata scsi_mod
Pid: 3586, comm: modprobe Not tainted 2.6.29-ARCH #1 System Product Name
RIP: 0010:[<ffffffffa04fab23>] [<ffffffffa04fab23>] drm_init+0x23/0x220 [drm]
RSP: 0018:ffff8800bb581eb8 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffffffffa0545760 RCX: 0000000000000000
RDX: ffffffff805b11c0 RSI: 0000000000000282 RDI: ffffffffa0543260
RBP: ffffffffa0069000 R08: 0000000000000000 R09: 0000000000000000
R10: 2222222222222222 R11: 2222222222222222 R12: 0000000000000000
R13: 00000000013fa620 R14: 0000000000000282 R15: 00000000013fa0e8
FS: 00007f520805b6f0(0000) GS:ffff8800bf805a00(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000282 CR3: 00000000bb6d2000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process modprobe (pid: 3586, threadinfo ffff8800bb580000, task ffff8800bddd8000)
Stack:
ffffffffa0543260 ffffffffa0545760 ffffffffa0069000 0000000000000000
00000000013fa620 00000000013fa0d0 00000000013fa0e8 ffffffff8020903b
ffffffff805b11c0 0000000000000282 ffffffff805b11c0 ffffffff8025ded9
Call Trace:
[<ffffffffa0069000>] ? radeon_init+0x0/0x1d [radeon]
[<ffffffff8020903b>] ? _stext+0x3b/0x180
[<ffffffff8025ded9>] ? __blocking_notifier_call_chain+0x69/0x90
[<ffffffff8027017f>] ? sys_init_module+0xaf/0x1f0
[<ffffffff8020c6aa>] ? system_call_fastpath+0x16/0x1b
Code: fb df eb 94 0f 1f 40 00 41 57 41 56 49 89 f6 41 55 41 54 55 53 48 83 ec 08 8b 05 89 71 02 00 48 89 3c 24 85 c0 0f 85 d9 01 00 00 <41> 8b 06 85 c0 0f 84 8c 00 00 00 8b 05 14 71 02 00 45 31 e4 4c
RIP [<ffffffffa04fab23>] drm_init+0x23/0x220 [drm]
RSP <ffff8800bb581eb8>
CR2: 0000000000000282
---[ end trace 94a33d21107180a4 ]---
eth0: no IPv6 routers present
cdrom: This disc doesn't have any tracks I recognize!
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
alg: No test for xts(twofish) (xts(twofish-generic))
NTFS driver 2.1.29 [Flags: R/W MODULE].
NTFS volume version 3.1.
Code : Tout sélectionner
Section "Module"
Load "glx"
Load "dri"
Load "drm"
EndSection
Section "Device"
Identifier "X1650Pro" # your alias
Driver "radeon"
Option "AccelMethod" "exa" # to enable 2D and Xv acceleration on R6XX - default AccelMethod shadowfb
Option "AccelDFS" "1" # mettre "1" si la carte n'est pas une AGP - s'utilise avec EXA
Option "ColorTiling" "on"
Option "EXAVSync" "yes"
Option "DPMS" "true" # gestion de l'énergie de l'écran
Option "DRI" "true"
Option "DMAForXv" "on"
EndSection
Section "ServerFlags"
Option "DontZap" "False"
EndSectionCode : Tout sélectionner
lspci |grep VGA
01:00.0 VGA compatible controller: ATI Technologies Inc RV530LE [Radeon X1600/X1650 PRO]
. Sans xorg.conf, l'affichage dans KDE est bien plus fluide, mais j'ai toujours un problème avec les vidéos...